Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 22 12月, 2010 1 次提交
  3. 21 12月, 2010 29 次提交
  5. 19 12月, 2010 5 次提交
    • S
      omap4: l2x0: Enable early BRESP bit · b89cd71a
      由 Santosh Shilimkar 提交于 
      The AXI protocol specifies that the write response can only
be sent back to an AXI master when the last write data has been
accepted. This optimization enables the PL310 to send the write
response of certain write transactions as soon as the store buffer
accepts the write address. This behavior is not compatible with
the AXI protocol and is disabled by default. You enable this
optimization by setting the Early BRESP Enable bit in the
Auxiliary Control Register (bit [30]).
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NMans Rullgard <mans@mansr.com>
Tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      b89cd71a
    • S
      omap4: l2x0: Set share override bit · b0f20ff9
      由 Santosh Shilimkar 提交于 
      Clearing bit 22 in the PL310 Auxiliary Control register (shared
attribute override enable) has the side effect of transforming Normal
Shared Non-cacheable reads into Cacheable no-allocate reads.

Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      b0f20ff9
    • M
      omap4: l2x0: enable instruction and data prefetching · 11e02640
      由 Mans Rullgard 提交于 
      Enabling L2 prefetching improves performance as shown on Panda
ES2.1 board with mem test, and it has measurable impact on
performances. I think we should consider it, even though it damages
"writes" a bit. (rebased to k.org)
Usually the prefetch is used at both levels together L1 + L2, however,
to enable the CP15 prefetch engines, these are under security, and on
GP devices, we cannot enable it(e.g. on PandaBoard). However, just
enabling PL310 prefetch seems to provide performance improvement,
as shown in the data below (from Ubuntu) and would be a great thing
to pull in.

What prefetch does is enable automatic next line prefetching. With this
enabled, whenever the PL310 receives a cachable read request, it
automatically prefetches the following cache line as well.

Measurement Data:
==
STOCK 10.10 WITHOUT PATCH

========================
~# ./memspeed
size    8388608 8192k 8M
offset  8388608, 0
buffers 0x2aaad000 0x2b2ad000
copy  libc          133 MB/s
copy  Android v5    273 MB/s
copy  Android NEON  235 MB/s
copy  INT32         116 MB/s
copy  ASM ARM       187 MB/s
copy  ASM VLDM 64   204 MB/s
copy  ASM VLDM 128  173 MB/s
copy  ASM VLD1      216 MB/s
read  ASM ARM       286 MB/s
read  ASM VLDM      242 MB/s
read  ASM VLD1      286 MB/s
write libc         1947 MB/s
write ASM ARM      1943 MB/s
write ASM VSTM     1942 MB/s
write ASM VST1     1935 MB/s

10.10 + PATCH
=============
~# ./memspeed
size    8388608 8192k 8M
offset  8388608, 0
buffers 0x2ab17000 0x2b317000
copy  libc          129 MB/s
copy  Android v5    256 MB/s
copy  Android NEON  356 MB/s
copy  INT32         127 MB/s
copy  ASM ARM       321 MB/s
copy  ASM VLDM 64   337 MB/s
copy  ASM VLDM 128  321 MB/s
copy  ASM VLD1      350 MB/s
read  ASM ARM       496 MB/s
read  ASM VLDM      470 MB/s
read  ASM VLD1      488 MB/s
write libc         1701 MB/s
write ASM ARM      1682 MB/s
write ASM VSTM     1693 MB/s
write ASM VST1     1681 MB/s
Signed-off-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      11e02640
    • S
      omap4: l2x0: Construct the AUXCTRL value using defines · 1773e60a
      由 Santosh Shilimkar 提交于 
      This patch removes the hardcoded value of auxctrl value and
construct it using bitfields

Bit 25 is reserved and is always set to 1. Same value
of this bit is retained in this patch
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      1773e60a
    • S
      ARM: l2x0: Add aux control register bitfields · 0aaa6f8f
      由 Santosh Shilimkar 提交于 
      This patch adds the PL310 Auxiliary Control Register bitfields
so that SOC's can use these bit fields to construct the AUXCTRL
value to be passed/programmed instead of hardcoding it.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      0aaa6f8f
  7. 18 12月, 2010 5 次提交
    • T
      Merge branch 'for_2.6.38' of git://gitorious.org/iommu_mailbox/iommu_mailbox... · c7d3e9e8
      由 Tony Lindgren 提交于 
      Merge branch 'for_2.6.38' of git://gitorious.org/iommu_mailbox/iommu_mailbox into devel-iommu-mailbox
      c7d3e9e8
    • A
      omap: remove dead wdt code in plat-omap/devices.c · 6bc56aae
      由 Anand Gadiyar 提交于 
      Commit f2ce6231 (OMAP: WDT: Split OMAP1 and OMAP2PLUS device
registration) removed omap_init_wdt and related structures from
plat-omap/devices.c. However a subsequent commit or merge
seems to have reintroduced these by accident. The caller of
omap_init_wdt was also removed by that commit, and this did
not get restored. So we have the following build warning now:

  CC      arch/arm/plat-omap/devices.o
arch/arm/plat-omap/devices.c:252: warning: 'omap_init_wdt' defined but not used

Fix this by removing this dead code.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      6bc56aae
    • J
      OMAP4: enable smc instruction in new assembler versions · fe297dde
      由 John Rigby 提交于 
      New assemblers need -march=armv7-a+sec on command line or
.arch_extension sec inline to enable use of the smc instruction.

This patch uses as-instr to check the latter to conditionally
enable the former in AFLAGS for files that use smc.

Checked on both old and new binutils to verify that it does
not break old versions.
Signed-off-by: NJohn Rigby <john.rigby@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      fe297dde
    • B
      omap: kill all section mismatch warning for omap2plus_defconfig · 1a6b5923
      由 Bryan Wu 提交于 
      This patch will kill following section mismatch warnings:

WARNING: vmlinux.o(.text+0x24a00): Section mismatch in reference from the function zoom_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function zoom_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because zoom_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.

WARNING: vmlinux.o(.text+0x24bfc): Section mismatch in reference from the function cm_t35_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function cm_t35_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because cm_t35_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.

WARNING: vmlinux.o(.data+0x1d3e0): Section mismatch in reference from the variable h4_config to the (unknown reference) .init.data:(unknown)
The variable h4_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: vmlinux.o(.data+0x1dc08): Section mismatch in reference from the variable sdp2430_config to the (unknown reference) .init.data:(unknown)
The variable sdp2430_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,

WARNING: vmlinux.o(.data+0x1e1d8): Section mismatch in reference from the variable apollon_config to the (unknown reference) .init.data:(unknown)
The variable apollon_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      1a6b5923
    • O
      omap: boards w/ wl12xx should select REGULATOR_FIXED_VOLTAGE · 7c50152f
      由 Ohad Ben-Cohen 提交于 
      Power to the wl12xx wlan device is controlled by a fixed regulator.

Boards that have the wl12xx should select REGULATOR_FIXED_VOLTAGE so
users will not be baffled.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      7c50152f