Update to version 1.2
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.

The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Sky2 driver will oops referencing bad memory if used on
a dual port card.  The problem is accessing past end of
MIB counter space.

Applies for both 2.6.17 and 2.6.16 (with fuzz)
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes the problem of some Dlink cards picking the wrong
driver.  It looks like these cards use Yukon 1 chipset, not Yukon 2.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Transmit buffers are always freed with interrupts enabled (softirq),
so we can just call dev_kfree_skb.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Unicast packets are shown as multicast, real multicast packets are missing.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Typo in last stats patch.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Set version to 1.1
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The hardware has additional error trap interrupt bits.  I have never seen
them trigger, but if they do, it looks like this might be useful.
Signed-off-by: NStephen Hemminger <shemminger@osdl.rog>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch decodes state and revovers from any races in the transmit
timeout and NAPI logic. It should never trigger, but if it does then
do the right thing.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Small whitespace fixes.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add MSI support to sky2 driver.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Change default coalescing parameters slightly, and allow wider
range of values.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Redo the interupt handling of sky2 driver based on the IRQ mangement
documentation. All interrupts are handled by the device0 NAPI poll
routine.

Don't need to adjust interrupt mask in IRQ context, done only when
changing device under RTNL. Therefore don't need hwlock anymore.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove wake on lan support for now. It doesn't work right, and I
don't have a machine with working suspend/resume to test or fix it.
It will be re-enabled later.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Yukon EC/rev0 (A1) chipset requires a bunch of workarounds. I copied these
from sk98lin.  But since they never got tested and add more cruft to the code;
any attempt at using driver as is on this version will probably fail.

It looks like this was a early engineering sample chip revision, if it ever shows
up on a real system. Produce an error message.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Turn on truncation to prevent getting choked by frames larger than expected.
Without this fix, driver hangs after receiving an oversize packet.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Avoid premature transmit ring full conditions.
Force a transmit status interrupt if transmit ring gets nearly full
and after a TSO send.

Allow more entries in transmit ring to be used if dma_addr is 32 bits
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Don't use sky2 to seed random pool beacause the network packet arrival time
will not be truly random due to NAPI and interrupt mitigation.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Remove Message Signaled Interrupt support (for 2.6.16).
MSI is inherently edge-triggered and that is incompatiable (without more
work) with NAPI.

In future, will replace with smarter lockless-IRQ handling like
tg3.c
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to avoid race in updating IRQ mask.  This can probably be replaced
smarter use of the interrupt control registers (if/when chipset
docs are available).
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

To avoid problems with PCI config access without ACPI (or busted ACPI tables),
use the device's window into PCI config space.

I know this probably will upset the purists, but I would rather have users
than ACPI testers. It also generates less code.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Need to force a transmit coalesce timer restart after processing
transmit packets. Otherwise, can get transmit status after last
update and chip doesn't send the next one.

Can go with the chip defaults for coalescing timers, except for
Tx timer which needs to be bigger.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Need to restart the interrupt coalescing timer after clearing the interrupt,
to avoid races with interrupt timer and processing.

Patch from Carl-Daniel Halfinger
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Don't allow coalescing values to be bigger than the transmit ring.
Since if you set them that big, the interrupt never happens and driver
livelocks.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Add more complete setup code for Yukon EC_U chipset.
Based on matching code in 8.31 code in SysKonnect vendor driver.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Users report problems w/ auto-negotiation disabled and the link set
to 100/Half or 10/Half.  Problems range from poor performance to no
link at all.

The current sky2 code does not set things properly on link up if
autonegotiation is disabled.  Plus it does not contemplate a 10Mbit
setting at all.  This patch corrects that.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Increase version, and get rid of out-dated comment.
Speed setting has worked for quite a while.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This hardware supports Message Signaled interrupts.
When setting up, use software interrupt to check for bad hardware.

Signed-off-by: Stephen Hemminger <shemminger @osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The sky2 interrupt can be used to add entropy.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Move the interrupt clear to before processing, this avoids a
possible races with status delaying.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Using the sky2 driver with bonding can result in oopses related to
reinitializing the PHY when the MAC address is changed (which bonding
is wont to do).  This patch changes sky2_set_mac_address to take less
drastic measures.

This is analagous to the skge patch here:

	http://lkml.org/lkml/2005/9/29/399

which fixed the issue here:

	http://bugzilla.kernel.org/show_bug.cgi?id=5271Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This fixes setting rx_coalesce_usecs_irq via ethtool in sky2.
The write was directed to the wrong register.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NCarl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

There were bugs in mmconfig access to PCI space, up to and
include 2.6.16-rc1. These prevented the sky2 driver from being
able to clear PCI express errors.

This patch makes the driver check (during probe), for errors
in PCI config access and fail.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix suspend/resume for sky2. The status ring was getting reallocated
and a bunch of other mistakes. Also, check return from power_state
on resume.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NJeff Garzik <jgarzik@pobox.com>