There is a second mouse sharing the same vendor strings but different IDs.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This mouse keeps disconnecting in runlevel 3. It needs the ALWAYS_POLL quirk.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The report descriptor for the HOLTEK USB ID 04d9:a0c2 (ETEKCITY Scroll
T-140 Gaming Mouse) is set to a very large amount of consumer usages
(2^16), exceeding HID_MAX_USAGES. Added id, bindings and comments for
the mouse, added to hid_have_special_driver, and reduced the usage and
logical maximums to 0x2fff, consistent with the other mice in the
category. Tested on the hardware.
Signed-off-by: NJohn C. DeSilva <desilvjo@umich.edu>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Enable the always-poll quirk for Elan Touchscreens found on some recent
Samsung laptops.

Without this quirk the device keeps disconnecting from the bus (and is
re-enumerated) unless opened (and kept open, should an input event
occur).

Note that while the device can be run-time suspended, the autosuspend
timeout must be high enough to allow the device to be polled at least
once before being suspended. Specifically, using autosuspend_delay_ms=0
will still cause the device to disconnect on input events.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch adds a seperate hid-penmount driver to work
around an issue with the HID report descriptor. The
descriptor does not contain the ContactID usage and as
result the touchscreen is represented as normal mouse
to the system.

This driver maps the button 0 emitted by the touchscreen
to BTN_TOUCH. This makes it possible to use touch events
in userspace.
Signed-off-by: NChristian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Ignore Jabra GN9350E HID interface. USB audio is working nicely, but
registering as HID blocks USB mouse buttons. Since special userspace programs
are needed we will avoid attaching usbhid drivers in general.
Signed-off-by: NPatrick Plattes <patrick@erdbeere.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This device generates ABS_Z and ABS_RX events instead of ABS_X and
ABS_Y.
Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add support for both ThinkPad Compact Bluetooth Keyboard with
TrackPoint and ThinkPad Compact USB Keyboard with TrackPoint.
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Reviewed-by: NAntonio Ospite <ao2@ao2.it>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Use word "tablet" in identifiers and comments instead of referring to specific
Huion tablet model name, as the product ID is used by at least several tablet
models.
Signed-off-by: NNikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

I am using a USB keyborad that give me "usb_submit_urb(ctrl) failed: -1" error
when I plugin it.  and I need to wait for 10s for this device to be ready.

By adding this quirks, the usb keyborad is usable right after plugin
Signed-off-by: NWangzhao Cai <microcaicai@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This device generates ABS_Z and ABS_RX events instead of ABS_X and
ABS_Y.
Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This driver adds support for USB controlled led panels that exists in
MSI GT683R laptop
Signed-off-by: NJanne Kanniainen <janne.kanniainen@gmail.com>
Reviewed-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

These device needs to be added to the quirks list with HID_QUIRK_NOGET,
otherwise they will reset upon receiving the get input report requests.
Signed-off-by: NJohn Sung <penmount.touch@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Added STM sensor hub new device id. Also added this new device
in HID_SENSOR_HUB_ENUM_QUIRK to fix report descriptors.
These devices uses old FW which uses logical 0 as minimum.
In these, HID reports are not using proper collection classes.
So we need to fix report descriptors,for such devices. This
will not have any impact, if the FW uses logical 1 as minimum.
Signed-off-by: NArchana Patni <archana.patni@intel.com>
Signed-off-by: NSubramony Sesha <subramony.sesha@intel.com>
Reviewed-by: NSrinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The device which identifies itself as a "USB Keykoard" (no typo) with VID:PID
1a2c:0023 does not seem to be handling the reports initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the kernel
when connected, and a delay before its initialization.  This patch adds the
quirk for this device, which causes the delay to disappear.

[jkosina@suse.cz: remove superfluous comment and fix ordering]
Signed-off-by: NDaniel Kamil Kozar <dkk089@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add the Microsoft Surface Pro 2 Type/Touch and default device hardware ID's
Set report quirk for the device in hid-sensor-hub
Signed-off-by: NReyad Attiyat <reyad.attiyat@gmail.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Some saitek mice implement a tristate button (for switching button mappings in
the original driver) by keeping one of three (non-physical)
buttons constantly pressed.

This breaks X and probably other userspace software.

This patch implements a quirk for the R.A.T.7 and M.M.O.7, tracking the mode
and generating presses of a single button if it changes.  Also the missing
release event is generated instantly.
Signed-off-by: NHarald Brinkmann <hbrinkmann@braincalibration.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The sensor hub in Lenovo Yogas needs the enumeration quirk.  I've been running
the patch for over a month with no problems, whereas the unpatched drivers
reliably mis-initialized the sensors.
Signed-off-by: NPeter F. Patel-Schneider <pfpschneider@gmail.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This touchpad seriously dislikes init reports, not only timeing out, but
also refusing to work after this.

Cc: stable@vger.kernel.org
Reported-and-tested-by: NVincent Fortier <th0ma7@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

They need to have the class SERIAL.

Note: it is a Win 7 panel, not Win 8 certified.
Signed-off-by: NTomas Sokorai <tsokorai@gmail.com>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This reverts commit 117309c5.

The MS Surface Pro 2 has an USB composite device with 3 interfaces
- interface 0 - sensor hub
- interface 1 - wacom digitizer
- interface 2 - the keyboard cover, if one is attached
This USB composite device changes it product id dependent on if and which
keyboard cover is attached. Adding the covers to hid_have_special_driver
prevents loading the right hid drivers for the other two interfaces, all 3
get loaded with hid-microsoft. We don't even need hid-microsoft for the
keyboards. We have to revert this to load the right hid modules for each
interface.

CC: stable@vger.kernel.org # kernel 3.14 only
Signed-off-by: NDerya <derya.kiran@yahoo.de>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Just like some of the other laptops/tablets on the market with ultrabook
sensors, the ThinkPad Helix's sensor hub requires a special quirk in
order for it to power on properly. Without it the sensors are detected
by the kernel and set up as usual, but they won't output any data. This
will also fix the sensors on any other laptops with the same model of
sensor hub.
Signed-off-by: NStephen Chandler Paul <thatslyude@gmail.com>
Acked-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The ANTON Touch Pad is a device which can switch from a multitouch
touchpad to a mouse. It thus presents several generic collections which
are currently ignored by hid-multitouch. Enable them by not ignoring
them in mt_input_mapping.
Adding also a suffix for them depending on their application.
Reported-by: NEdel Maks <edelmaks@gmail.com>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch adds support for the Silicon Labs CP2112 "Single-Chip HID USB to
SMBus Master Bridge."

This is a HID device driver which registers as an i2c adapter and gpiochip to
expose these functions of the CP2112. The customizable USB descriptor fields
are exposed as sysfs attributes.  The SMBus byte-read, byte-data-read/write,
and word-data-read transfer modes have been tested by talking to an i2c
sensor.  The GPIO functions and USB descriptor field programming have also
been tested.
Signed-off-by: NDavid Barksdale <dbarksdale@uplogix.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Added STM sensor hub vendor id in HID_SENSOR_HUB_ENUM_QUIRK to
fix report descriptors. These devices uses old FW which uses
logical 0 as minimum. In these, HID reports are not using proper
collection classes. So we need to fix report descriptors,for
such devices. This will not have any impact, if the FW uses
logical 1 as minimum.

We look for usage id for "power and report state", and modify
logical minimum value to 1.

This is a follow-up patch to commit id 875e36f8.
Signed-off-by: NArchana Patni <archana.patni@linux.intel.com>
Reviewed-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The "Webmail Notifier" is a USB controlled LED that appears as a HID
device. When trying to change the LED via hidraw it returns malformed
reports. As "usbled" supports it, we blacklist it in usbhid.
Signed-off-by: NChristian Vogel <vogelchr@vogel.cx>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add Apple wireless keyboard 2011 JIS model (05ac:0257).
Signed-off-by: NHuei-Horng Yo <hiroshi@ghostsinthelab.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The Microsoft Office keyboard has a scrollwheel as well as some special keys
above the keypad which are handled through the custom MS usage page, this
commit adds support for these.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This is a Win7 device which does not work correctly with the default
settings (not the previous default BT).
However, the quirk ALWAYS_TRUE makes it working like a charm.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The Microsoft Surface Type/Touch cover 2 devices have the flag HID_DG_CONTACTID
in their reports.This causes the device to bind to the hid-multitouch driver,
which doesn't handle generic keyboard/mouse input events.  The patch adds
the hardware id's of the device to hid-microsoft and to the HID special
driver array, which makes the device get handled by hid-generic/hid-input
properly.

Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=64811Singed-off-by: NReyad Attiyat <reyad.attiyat@gmail.com>
Reviewed-by: Benjamin Tissoires<benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

There is timeout error during initialization:
kernel: [   11.733104] hid-multitouch 0003:1870:0110.0001: usb_submit_urb(ctrl) failed: -1
kernel: [   11.734093] hid-multitouch 0003:1870:0110.0001: timeout initializing reports

Adding quirk HID_QUIRK_NO_INIT_REPORTS can solve the problem.
Signed-off-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Added support of RITMIX ROM-316 mouse to hid-holtek-mouse workaround module
Signed-off-by: NAlexey Kharlamov <derlafff@ya.ru>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This addresses regression caused by commit id "751d17e2"
 iio: hid-sensors: Fix power and report state.
This commit removed a quirk, to change the enumeration base
to 1 from 0 based on an CONFIG paramter. There was objection to
add more changes under this quirk, instead suggested to add an
HID quirk. But there is no easy way to add HID qurik as the
reports are not properly using collection class.

The solution was to use logical minimum, which is a correct way.
There were changes done in firmware to address this.

Unfortunately some devices, still use old FW and can't be upgraded
to newer version on Linux devices as there is no FW upgrade tool
available for Linux devices. So we need to fix report descriptors,
for such devices. This will not have any impact, if the FW uses
logical 1 as minimum.

In this patch we look for usage id for "power and report state", and
modify logical minimum value to 1.

Background on enum:
In the original HID sensor hub firmwares all Named array enums were
to 0-based. But the most recent hub implemented as 1-based,
because of the implementation by one of the major OS vendor.
Using logical minimum for the field as the base of enum. So we add
logical minimum to the selector values before setting those fields.
Some sensor hub FWs already changed logical minimum from 0 to 1
to reflect this and hope every other vendor will follow.
There is no easy way to add a common HID quirk for NAry elements,
even if the standard specifies these field as NAry, the collection
used to describe selectors is still just "logical".
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Adds the Dualshock 4 to the HID device list and enables force-feedback.

Adds a Dualshock 4 specific worker function since the Dualshock 4 needs a
different report than the Sixaxis.

The right motor in the Dualshock 4 is variable so the full rumble value
is now passed to the worker function and clamped there if necessary.
Signed-off-by: NFrank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The Si4713 development board contains a Si4713 FM transmitter chip
and is handled by the radio-usb-si4713 driver.
The board reports itself as (10c4:8244) Cygnal Integrated Products, Inc.
and misidentifies itself as a HID device in its USB interface descriptor.
This patch ignores this device as an HID device and hence loads the custom driver.
Signed-off-by: NDinesh Ram <dinesh.ram@cern.ch>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NEduardo Valentin <edubezval@gmail.com>
Acked-by: NEduardo Valentin <edubezval@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

[jkosina@suse.cz: refresh to apply after SIS quirk merging]
Signed-off-by: NEmanuel Krenz <emanuelkrenz@web.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

I have two Logitech Dual Action gamepads, both have same Vendor/Device id pair.
Newest gamepad (A) can switch between old mode (HID) and XBox gamepad emulation
mode. Old gamepad (B) can only work in HID mode.  In HID mode gamepad A sends
many EPIPE errors during initialization and was disconnected immediately after
connect  to usb port. It works fine in Win and Mac. After adding NOGET quirk in
driver, it was working properly.  Gamepad B works fine before and after
changes. I tested both gamepads with 3.8.0 and 3.11.6 kernels  with modified
driver. Follow patch can apply for current git kernel version. I can send pcap
log from usb bus with both gamepads or any other additional information if it
is needed
Signed-off-by: NVitaly Katraew <zawullon@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add Synaptics HD touchscreen(06cb:1ac3) to no init report quirk
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add Synaptics HD touchscreen(06cb:0ac3) to no init report quirk.
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

USB_VENDOR_ID_SIS and USB_VENDOR_ID_SIS2_TOUCH are identical,
so refine the code and merge the quirks.
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>