There are some corner cases where the driver could get stuck with a full
tid queue that is paused, leading to a software tx queue hang.

Since the tx queueing rework, pausing per-tid queues on aggregation
session setup is no longer necessary. The driver will assign sequence
numbers to buffered frames when a new session is established, in order
to get the correct starting sequence number.

mac80211 prevents new frames from entering the queue during setup.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the amount of noise fluctuates strongly, low immunity settings
can sometimes disrupt signal detection on AR913x chips. When that
happens, no OFDM/CCK errors are reported anymore, and ANI tunes the
radio to the lowest immunity settings.
Usually rx/tx fails as well in that case.

To fix this, keep noise immunity settings at or above ANI default level,
which will keep radio parameters at or above INI values.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for the AR9462 chip

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3007 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NMohammed Habibulla <moch@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When we're performing reauthentication (in order to elevate the
security level from an unauthenticated key to an authenticated one) we
do not need to issue any encryption command once authentication
completes. Since the trigger for the encryption HCI command is the
ENCRYPT_PEND flag this flag should not be set in this scenario.
Instead, the REAUTH_PEND flag takes care of all necessary steps for
reauthentication.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Commit 1c2e0041 introduced an event handler for the encryption key
refresh complete event with the intent of fixing some LE/SMP cases.
However, this event is shared with BR/EDR and there we actually want to
act only on the auth_complete event (which comes after the key refresh).

If we do not do this we may trigger an L2CAP Connect Request too early
and cause the remote side to return a security block error.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

This reverts commit d2bee8fb.

Enabling autosuspend for Intel Bluetooth devices has been shown to not
work reliable. It does work for some people with certain combinations
of USB host controllers, but for others it puts the device to sleep and
it will not wake up for any event.

These events can be important ones like HCI Inquiry Complete or HCI
Connection Request. The events will arrive as soon as you poke the
device with a new command, but that is not something we can do in
these cases.

Initially there were patches to the xHCI USB controller that fixed
this for some people, but not for all. This could be well a problem
somewhere in the USB subsystem or in the USB host controllers or
just plain a hardware issue somewhere. At this moment we just do
not know and the only safe action is to revert this patch.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: Tedd Ho-Jeong An <tedd.an@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

brcmfmac has been broken on my cubietruck with a BCM43362:

brcmfmac: brcmf_chip_recognition: found AXI chip: BCM43362, rev=1
brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0:
        Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d

since commit 53036261: "brcmfmac: update core reset and disable routines".

The problem is that since this commit brcmf_chip_ai_resetcore no longer sets
BCMA_IOCTL itself before bringing the core out of reset, instead relying on
brcmf_chip_ai_coredisable to do so. But brcmf_chip_ai_coredisable is a nop
of the chip is already in reset. This patch modifies brcmf_chip_ai_coredisable
to always set BCMA_IOCTL even if the core is already in reset.

This fixes brcmfmac hanging in firmware loading on my board.

Cc: stable@vger.kernel.org # v3.14
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: move sc_flags to ath_common" moved setting
ATH_OP_INVALID flag below ieee80211_register_hw. This is causing
the flag never being cleared randomly as the drv_start is called
prior to setting flag. Fix this by setting the flag prior to
register_hw.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement a recv budget so that in cases of high traffic we still allow other
taskets to get processed.

Without this, we can encounter a host of issues during high wireless traffic
reception depending on system load including rcu stall's detected (ARM),
soft lockups, failure to service critical tasks such as watchdog resets,
and triggering of the tx stuck tasklet.

The same thing was proposed previously by Ben:
 http://www.spinics.net/lists/linux-wireless/msg112891.html

The only difference here is that I make sure only processed packets are counted
in the budget by checking at the end of the rx loop.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a flush is requested, make sure to clear the descriptor once we've
processed it.

This resolves a hang that will occur if all RX descriptors are full when a
flush is requested.
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

static code analysis from cppcheck reports:

[drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:322]:
  (error) Uninitialized variable: packet_beacon

packet_beacon is not initialized and hence packet_beacon
contains garbage from the stack, so set it to false.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Cc: Stable <stable@vger.kernel.org> [3.10+]
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Let's formalize what must have been blatantly clear from my level
of activity is the past year(s).
I simply do not have time for this anymore.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When disable beaconing we clear register with beacon and newer set it
back, what make we stop send beacons infinitely.

Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes when command timeout occurs due to a firmware or
hardware bug, there may be some synchronous commands in command
queue. These commands are never downloaded to firmware causing
hung task warnings. This patch replaces wait_event_interruptible
call with wait_event_interruptible_timeout to fix the issue.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During extended scan, SCAN report event is always followed by
command response. Sometimes It is observed that command response
is processed before SCAN report which leads to a crash, because
current command node is cleared while handling the response.
This patch makes sure that driver's main thread gives priority
to events over command responses.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMaithili Hinge <maithili@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some fields are missing from the event mailbox
struct definitions, which cause issues when
trying to handle some events.

Add the missing fields in order to align the
struct size (without adding actual support
for the new fields).
Reported-and-tested-by: NImre Kaloz <kaloz@openwrt.org>
Cc: stable@vger.kernel.org # 3.14+
Fixes: 028e7243 ("wl18xx: move to new firmware (wl18xx-fw-3.bin)")
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a potential memory leak in the error path of function
rsi_send_auto_rate_request(). In case memory allocation for array
'selected_rates' fails, the error path exits and leaves the previously
allocated skb in place. Detected by Coverity: CID 1195575.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This array is used in debug string to display cw1200_link_status
defined in drivers/net/wireless/cw1200/cw1200.h.

Add missing strings for CW1200_LINK_RESET and CW1200_LINK_RESET_REMAP.
Signed-off-by: NFrederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes the firmware sends a dummy packet event while we are in PLT
mode.  This doesn't make sense, it's a firmware bug.  Fix this by
ignoring dummy packet events when we're PLT mode.
Reported-by: NYegor Yefremov <yegorslists@googlemail.com>
Reported-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a potential memory leak in function rsi_set_channel() that is used to
program channel changes. The channel check block for the frequency bands
directly exits the function in case of an error, thus leaving an already
allocated skb unreferenced. Move the checks above allocating the skb.
Detected by Coverity: CID 1195576.
Signed-off-by: NChristian Engelmayer <cengelma@gmx.at>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/rsi/rsi_91x_core.c: In function ‘rsi_core_determine_hal_queue’:
drivers/net/wireless/rsi/rsi_91x_core.c:91: warning: ‘ii’ may be used uninitialized in this function
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few entries were wrong and this caused throughput issues.

Cc: <stable@vger.kernel.org> [3.13+]
Fixes: dac94da8 ("iwlwifi: mvm: new BT Coex API")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The per rate stats should be cleared when aggregation state changes
to avoid making rate scale decisions based on throughput figures which
were collected prior to the aggregation state change and are now stale.
While at it make sure any clearing of the per rate stats will get logged.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Don't search columns which are unlikely to succeed as previous
columns searched with less aggressive modulation failed.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow switching back to legacy Tx columns so we'll stop doing
HT/VHT in case we're far from the AP. Stop active aggregation when
making a deciding to stay in a legacy column.
Despite having low legacy rates in the LQ table lower entries
it doesn't help much in case we're doing aggregations as the
aggregation was being transmitted in the initial rate of the table.

This should help traffic stalls when far from the AP.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

After being idle for a long time (>5sec) the rs statistics
will be stale so we prefer to reset rs and start from legacy
rates again. This gives better results when the attenuation
increased signficantly (e.g. we got further from the AP) and
after a while we start Tx
Note that the first Tx after the idle period will still go out
in the old modulation and rate but this seemed a simpler approach
compared to adding a timer or modifying mac80211 for this.
The negative impact is negligble as we'll recover quickly.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Change the down/upscale decision logic a bit to be based
on different success ratio thresholds. This fixes the implementation
compared to the rate scale algorithm which was planned to yield
optimal results. Also fix a case where a lower rate wasn't explored
despite being a potential for better throughput.
While at it rewrite rs_get_rate_action to be more clear and clean.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The selection of the max expected throughput for a column
didn't take into account the maximal allowed rate for the current
peer. This can cause unnecessary switches during the search cycle
to columns which have no chance of beating the current throughput.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It was missing.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This will allow to load the new firmware.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add 2 new HW IDs for the 7265 series.

Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

I forgot to send the new Look Up Table to the firmware and
I also forgot to free the command which is kzalloc'ed.
This code is relevant for 7265 device only.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

mimo_delim was always set to 0 instead of pointing to
the first SISO entry after MIMO rates.
This can cause keep transmitting in MIMO even when we shouldn't.
For example when the peer is requesting static SMPS.

Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If we have no beacon data before association, delay smart FIFO
enablement until after we have this data.

Not doing so can cause association failures in extremely silent
environments (usually only a shielded box/room) as beacon RX is
not sent to the host immediately, and then the association time
event ends without the host receiving any beacon even though it
was on the air - it's just stuck on the FIFO.

Cc: <stable@vger.kernel.org> [3.14]
Fixes: 1f3b0ff8 ("iwlwifi: mvm: Add Smart FIFO support")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull misc kbuild changes from Michal Marek:
 "Here is the non-critical part of kbuild:
   - One bogus coccinelle check removed, one check fixed not to suggest
     the obsolete PTR_RET macro
   - scripts/tags.sh does not index the generated *.mod.c files
   - new objdiff tool to list differences between two versions of an
     object file
   - A fix for scripts/bootgraph.pl"

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  scripts/coccinelle: Use PTR_ERR_OR_ZERO
  scripts/bootgraph.pl: Add graphic header
  scripts: objdiff: detect object code changes between two commits
  Coccicheck: Remove memcpy to struct assignment test
  scripts/tags.sh: Ignore *.mod.c

This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.

When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.

This function aborts them with DID_SOFT_ERROR.

If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.

The result is that disk returning QUEUE FULL causes request failures.

The error was reproduced on 53c895 with COMPAQ BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags.  The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags.  The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 8f619b54 ("powerpc/ppc64: Do not turn AIL (reloc-on
interrupts) too early") added code to set the AIL bit in the LPCR
without checking whether the kernel is running in hypervisor mode.  The
result is that when the kernel is running as a guest (i.e., under
PowerKVM or PowerVM), the processor takes a privileged instruction
interrupt at that point, causing a panic.  The visible result is that
the kernel hangs after printing "returning from prom_init".

This fixes it by checking for hypervisor mode being available before
setting LPCR.  If we are not in hypervisor mode, we enable relocation-on
interrupts later in pSeries_setup_arch using the H_SET_MODE hcall.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>