Every path that ends up at do_sparc64_fault() must install a valid
FAULT_CODE_* bitmask in the per-thread fault code byte.

Two paths leading to the label winfix_trampoline (which expects the
FAULT_CODE_* mask in register %g4) were not doing so:

1) For pre-hypervisor TLB protection violation traps, if we took
   the 'winfix_trampoline' path we wouldn't have %g4 initialized
   with the FAULT_CODE_* value yet.  Resulting in using the
   TLB_TAG_ACCESS register address value instead.

2) In the TSB miss path, when we notice that we are going to use a
   hugepage mapping, but we haven't allocated the hugepage TSB yet, we
   still have to take the window fixup case into consideration and
   in that particular path we leave %g4 not setup properly.

Errors on this sort were largely invisible previously, but after
commit 4ccb9272 ("sparc64: sun4v TLB
error power off events") we now have a fault_code mask bit
(FAULT_CODE_BAD_RA) that triggers due to this bug.

FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS
(see #1 above) and thus we get seemingly random bus errors triggered
for user processes.

Fixes: 4ccb9272 ("sparc64: sun4v TLB error power off events")
Reported-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Move all files from sparc64/kernel/ to sparc/kernel
  - rename as appropriate
o Update sparc/Makefile to the changes
o Update sparc/kernel/Makefile to include the sparc64 files

NOTE: This commit changes link order on sparc64!

Link order had to change for either of sparc32 and sparc64.
And assuming sparc64 see more testing than sparc32 change link
order on sparc64 where issues will be caught faster.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sequence to move over to the Linux trap tables from
the firmware ones needs to be more air tight.  It turns
out that to be %100 safe we do need to be able to translate
OBP mappings in our TLB miss handlers early.

In order not to eat up a lot of kernel image memory with
static page tables, just use the translations array in
the OBP TLB miss handlers.  That solves the bulk of the
problem.

Furthermore, to make sure the OBP TLB miss path will work
even before the fixed MMU globals are loaded, explicitly
load %g1 to TLB_SFSR at the beginning of the i-TLB and
d-TLB miss handlers.

To ease the OBP TLB miss walking of the prom_trans[] array,
we sort it then delete all of the non-OBP entries in there
(for example, there are entries for the kernel image itself
which we're not interested in at all).

We also save about 32K of kernel image size with this change.
Not a bad side effect :-)

There are still some reasons why trampoline.S can't use the
setup_trap_table() yet.  The most noteworthy are:

1) OBP boots secondary processors with non-bias'd stack for
   some reason.  This is easily fixed by using a small bootup
   stack in the kernel image explicitly for this purpose.

2) Doing a firmware call via the normal C call prom_set_trap_table()
   goes through the whole OBP enter/exit sequence that saves and
   restores OBP and Linux kernel state in the MMUs.  This path
   unfortunately does a "flush %g6" while loading up the OBP locked
   TLB entries for the firmware call.

   If we setup the %g6 in the trampoline.S code properly, that
   is in the PAGE_OFFSET linear mapping, but we're not on the
   kernel trap table yet so those addresses won't translate properly.

   One idea is to do a by-hand firmware call like we do in the
   early bootup code and elsewhere here in trampoline.S  But this
   fails as well, as aparently the secondary processors are not
   booted with OBP's special locked TLB entries loaded.  These
   are necessary for the firwmare to processes TLB misses correctly
   up until the point where we take over the trap table.

This does need to be resolved at some point.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!