BUG_ONs doesn't help anything except for stop the system from
running. If it occurs, it implies we should deploy proper error
handling for that. So this patch is gonna discard these meaningless
BUG_ONs and deploy error handling if needed.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When initializing sdio card, we get struct mmc_card
from mmc_alloc_card which allocates it by kzalloc. So we
don't need another memset while reading cccr.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

While in sdhci_execute_tuning() the choice whether or not to enable the
tuning is done on the actual timing, in the mmc_sdio_init_uhs_card() the
check is done on the capability of the card.

This difference is causing some issues with some SDIO cards in DDR50
mode where the CDM19 is wrongly issued.

With this patch we modify the check in both
mmc_(sd|sdio)_init_uhs_card() functions to take the proper decision
only according to the actual timing specification.

Cc: stable@vger.kernel.org
Signed-off-by: NCarlo Caione <carlo@endlessm.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The 'ocr' parameter passed to mmc_set_signal_voltage()
defines the power-on voltage used when power cycling
after a failure to set the voltage.  However, in the
case of mmc_sdio_init_card(), the value passed has the
R4_18V_PRESENT flag set which is not valid for power-on
and results in an invalid vdd.  Fix by passing the card's
ocr value which does not have the flag.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.

Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.

To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>

As mmc_claim_host() invokes pm_runtime_get_sync() for the mmc host device,
it's important that the host is kept claimed for *all* accesses to it via
the host_ops callbacks.

In some code paths for SDIO, particularly related to the PM support,
mmc_power_off|up() is invoked without keeping the host claimed. Let's fix
these.

Moreover, mmc_start|stop_host() also invokes mmc_power_off|up() without
claiming the host, let's fix these as well.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NKishon Vijay Abraham I <kishon@ti.com>

In preparation for adding drive strength support
for eMMC, add drive_strength to struct mmc_card
to record the card drive strength for UHS-I modes
and HS200 / HS400. For eMMC this will be needed
when switching between HS200 and HS400.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Make a new function out of common code used for drive
strength selection.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In preparation for supporting also eMMC drive strength,
add the 'card' as a parameter so that the callback can
distinguish different types of cards if necessary.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Card drive strength selection uses a callback to
which a mask of supported drive strengths is passed.
Currently, the bits are checked against the values
in the SD specifications. That is not necessary
because the callback will anyway match the mask
against a valid value. Simplify by taking the mask
as is but still ensuring that the default mandatory
value (type B) is always supported.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Initialization of UHS-I modes for SD and SDIO cards
employs a callback to allow the host driver to
choose a drive strength value. Currently that
assumes the card drive strength and host driver
type must be the same value. Change to let the
callback make that decision and return both the
card drive strength and host driver type.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enable re-tuning when tuning is executed and
disable re-tuning when card is no longer initialized.

In the case of SDIO suspend, the card can keep power.
In that case, re-tuning need not be disabled, but, if
a re-tuning timer is being used, ensure it is disabled
and assume that re-tuning will be needed upon resume
since it is not known how long the suspend will last.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some drivers schedule automatic hw resets. An example is mwifiex,
which schedules a card reset if the command handler between driver
and card firmware becomes out of sync
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Every call to sdio_enable_4bit_bus is followed (on success) by a call
to mmc_set_bus_width().

To simplify the code, include those calls directly in
sdio_enable_4bit_bus().
Signed-off-by: NNeilBrown <neil@brown.name>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For each MMC, SD and SDIO there is code that
holds the clock, calls ops->execute_tuning, and
releases the clock. Simplify the code a bit by
providing a separate function to do that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_sdio_power_restore() calls
	mmc_send_if_cond(host, host->card->ocr);

	ret = mmc_send_io_op_cond(host, 0, NULL);

between mmc_go_idle() and mmc_sdio_init_card().
mmc_sdio_resume() needs to as well, else my libertas sdio wifi
device doesn't resume properly from suspend.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As we are restoring power to a known card, it makes sense to use
the 'ocr' value known for the card rather than the generic one
for the host interface.
This matches the use of card->ocr passed to mmc_power_up in
mmc_sdio_runtime_resume  (just before mmc_sdio_power_restore is
called), and the value passed to mmc_sdio_init_card() a little
later in mmc_sdio_power_restore().
Suggested-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Use the much more common pr_warn instead of pr_warning.

Other miscellanea:

o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

781e989c ("mmc: sdhci: convert to new SDIO IRQ handling") and
bf3b5ec6 ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151

In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <chris@printf.net>
Signed-off-by: NFu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Timing mode identifier has same role and can take the place
of speed mode. This change removes all related speed mode.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <chris@printf.net>

The sdio func device is added to the driver model after the card
device.

This means the sdio func device will be suspend before the card device
and thus resumed after. The consequence are the mmc core don't
explicity need to protect itself from receiving sdio requests in
suspended state. Instead that can be handled from the sdio bus, which
is thus invokes the PM callbacks instead of old dummy function.

In the case were the sdio func driver don't implement the PM callbacks
the mmc core will in the early phase of system suspend, remove the
card from the driver model and thus power off it.

Cc: Aaron Lu <aaron.lu@intel.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Reviewed-by: NAaron Lu <aaron.lu@intel.com>
Tested-by: Nxiaoming wang <xiaoming.wang@intel.com>
Tested-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: NChris Ball <chris@printf.net>

Since mmc_select_voltage now only gets called from the attach sequence,
it makes sense to move the out of spec validations of the card ocr into
this function.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

According to eMMC/SD/SDIO specs, the VDD (VCC) voltage level must be
maintained during the initialization sequence. If we want/need to tune
the voltage level, a complete power cycle of the card must be executed.

Most host drivers conforms to the specifications by only allowing to
change VDD voltage level at the MMC_POWER_UP state, but some also cares
about MMC_POWER_ON state, which they should'nt. This patch will not
break those drivers, but they could clean up code to better reflect
what is expected from the protocol layer.

A big re-work of the mmc_select_voltage function is done to only change
VDD voltage level if the host supports MMC_CAP2_FULL_PWR_CYCLE.
Otherwise only validation of the host and card ocr mask will be done.

A very nice side-effect of this patch is that we now don't need to
reset the negotiated ocr mask at the mmc_power_off function, since now
it will actually reflect the present voltage level, which safely can be
used at the next power up and re-initialization. Moreover, we then only
need to execute mmc_select_voltage from the attach sequence.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The negotiated ocr mask is directly related to the card. Once a card
gets removed, the mask shall be dropped. By moving the cache of the ocr
mask from the host struct to the card struct we have accomplished this.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

At several places in mmc_sdio_init_card function the cached mask in
host->ocr were being updated. To simplify code, we make use of an
local ocr parameter instead.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The retry and fallback mechanism when failing to switch to 1.8V
signaling voltage is handled by the SDIO card init function. Thus we
can remove the duplicated old code from the attach function.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This is yet another step of restructure code to be able to fixup the
setup of the negotiated ocr mask.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

As a step to fixup the setup of the negotiated ocr mask, we need the
mmc_power_up|cycle functions to take the ocr as a parameter.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

By moving code from the mmc_suspend|resume_host down into each
.suspend|resume bus_ops callback, we get a more flexible solution.

Some nice side effects are that we get a better understanding of each
bus_ops suspend|resume sequence and the common code don't have to take
care of specific corner cases, especially for the SDIO case.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch moves the validation for all the suspend prerequisites to be
done at SUSPEND_PREPARE notification. Previously in the SDIO case parts
of the validation was done from mmc_suspend_host.

This patch invents a new pre_suspend bus_ops callback and implements it
for SDIO. Returning an error code from it, will mean at SUSPEND_PREPARE
notification, the card will be removed before proceeding with the
suspend sequence.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SDIO is the only protocol that uses runtime pm for the card device
right now. To provide the option for sd and mmc to use runtime pm as
well the bus_ops callback are extended with two new functions. One for
runtime_suspend and one for runtime_resume.

This patch will also implement the callbacks for SDIO to make sure
existing functionality is maintained. It also prepares to move
away from using the mmc_power_restore_host API, since it is not
needed when using runtime PM.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Only execute tuning for sd and sdio devices that are using
SDR50 or SDR104.

Make sure clock is hold during tuning for sdio devices.
Signed-off-by: NFredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Acked-by: NJohan Rudholm <jrudholm@gmail.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put_noidle in such case.
Signed-off-by: NLiu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: NLi Fei <fei.li@intel.com>
Acked-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

When switching SD and SDIO cards from 3.3V to 1.8V signal levels, the
clock should be gated for 5 ms during the step. After enabling the
clock, the host should wait for at least 1 ms before checking for
failure. Failure by the card to switch is indicated by dat[0:3] being
pulled low. The host should check for this condition and power-cycle
the card if failure is indicated.

Add a retry mechanism for the SDIO case.

If the voltage switch fails repeatedly, give up and continue the
initialization using the original voltage.

This patch places a couple of requirements on the host driver:

 1) mmc_set_ios with ios.clock = 0 must gate the clock
 2) mmc_power_off must actually cut the power to the card
 3) The card_busy host_ops member must be implemented

if these requirements are not fulfilled, the 1.8V signal voltage switch
will still be attempted but may not be successful.
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: NKevin Liu <kliu5@marvell.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

Allow callers to access the start_signal_voltage_switch host_ops
member without going through any cmd11 logic. This is mostly a
preparation for the following signal voltage switch patch.

Also, reset ios.signal_voltage to its original value if
start_signal_voltage_switch fails.
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

When SDIO3.0 card is detected, incorrect bus speed mode
is printed as part of card detection print in kernel logs.

This change fixes it so that user won't be confused by
looking at incorrect card detection message in logs.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Tested-by: NJackey Shen <Jackey.Shen@amd.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

According to UHS-I initialization sequence for SDIO 3.0 cards,
the host must set bit[24] (S18R) of OCR register during OCR
handshake to know whether the SDIO card is capable of doing
1.8V I/O.
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

If SDIO keep power flag (MMC_PM_KEEP_POWER) is not set, card would
be reinitialized during resume but as we are not resetting
(CMD52 reset) the SDIO card during this reinitialization, card may
fail to respond back to subsequent commands (CMD5 etc...).

This change resets the card before the reinitialization of card
during resume.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

When SDIO3.0 card is detected, incorrect bus speed mode
is printed as part of card detection print in kernel logs.

This change fixes it so that user won't be confused by
looking at incorrect card detection message in logs.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Tested-by: NJackey Shen <Jackey.Shen@amd.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

According to UHS-I initialization sequence for SDIO 3.0 cards,
the host must set bit[24] (S18R) of OCR register during OCR
handshake to know whether the SDIO card is capable of doing
1.8V I/O.
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>