mmc: core: Collect common code for card ocr validation

Since mmc_select_voltage now only gets called from the attach sequence,
it makes sense to move the out of spec validations of the card ocr into
this function.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

drivers/mmc/core/core.c

@@ -1357,6 +1357,16 @@ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
 {
 	int bit;
 
+	/*
+	 * Sanity check the voltages that the card claims to
+	 * support.
+	 */
+	if (ocr & 0x7F) {
+		dev_warn(mmc_dev(host),
+		"card claims to support voltages below defined range\n");
+		ocr &= ~0x7F;
+	}
+
 	ocr &= host->ocr_avail;
 	if (!ocr) {
 		dev_warn(mmc_dev(host), "no support for card's volts\n");

drivers/mmc/core/mmc.c

@@ -1666,17 +1666,6 @@ int mmc_attach_mmc(struct mmc_host *host)
 			goto err;
 	}
 
-	/*
-	 * Sanity check the voltages that the card claims to
-	 * support.
-	 */
-	if (ocr & 0x7F) {
-		pr_warning("%s: card claims to support voltages "
-		       "below the defined range. These will be ignored.\n",
-		       mmc_hostname(host));
-		ocr &= ~0x7F;
-	}
-
 	rocr = mmc_select_voltage(host, ocr);
 
 	/*

drivers/mmc/core/sd.c

@@ -1231,25 +1231,6 @@ int mmc_attach_sd(struct mmc_host *host)
 			goto err;
 	}
 
-	/*
-	 * Sanity check the voltages that the card claims to
-	 * support.
-	 */
-	if (ocr & 0x7F) {
-		pr_warning("%s: card claims to support voltages "
-		       "below the defined range. These will be ignored.\n",
-		       mmc_hostname(host));
-		ocr &= ~0x7F;
-	}
-
-	if ((ocr & MMC_VDD_165_195) &&
-	    !(host->ocr_avail_sd & MMC_VDD_165_195)) {
-		pr_warning("%s: SD card claims to support the "
-		       "incompletely defined 'low voltage range'. This "
-		       "will be ignored.\n", mmc_hostname(host));
-		ocr &= ~MMC_VDD_165_195;
-	}
-
 	rocr = mmc_select_voltage(host, ocr);
 
 	/*

drivers/mmc/core/sdio.c

@@ -1133,16 +1133,6 @@ int mmc_attach_sdio(struct mmc_host *host)
 	if (host->ocr_avail_sdio)
 		host->ocr_avail = host->ocr_avail_sdio;
 
-	/*
-	 * Sanity check the voltages that the card claims to
-	 * support.
-	 */
-	if (ocr & 0x7F) {
-		pr_warning("%s: card claims to support voltages "
-		       "below the defined range. These will be ignored.\n",
-		       mmc_hostname(host));
-		ocr &= ~0x7F;
-	}
 
 	rocr = mmc_select_voltage(host, ocr);