Since these boards can boot out of NAND, make sure we give u-boot its
own partition by default to avoid clobbering it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Now that the driver for the Blackfin on-chip NFC no longer uses/respects
the page_size from the platform resources (figures out the needs on the
fly), drop it from the platform resources.  This fixes some build errors
since the defines no longer exists.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

These boards all have the GPIO VRSEL hooked up as an active high.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This lets us support the new BF527-EZKIT V2.1 via platform resources
tweaks only.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This lets people easily select the UART/SPORT consoles for early printk
while leveraging the pins declared in the boards file.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Rather than keeping the pins in the actual driver and worrying about a
mess of Kconfig options, declare all the desired pin resources in the
boards file.  This lets people easily select the specific pins/ports for
the normal emulated UART as well as GPIOs for CTS/RTS.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Rather than keeping the pins in the actual driver and worrying about a
mess of Kconfig options, declare all the desired pin resources in the
boards file.  This lets people easily select the specific pins/ports for
the normal UART as well as GPIOs for CTS/RTS.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The simple-gpio has been replaced by the gpio sysfs interface, so drop the
unused simple-gpio resources from all Blackfin boards.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Bill Gatliff & David Brownell pointed out we were missing some
copyrights, and licensing terms in some of the files in
./arch/blackfin, so this fixes things, and cleans them up.

It also removes:
 - verbose GPL text(refer to the top level ./COPYING file)
 - file names (you are looking at the file)
 - bug url (it's in the ./MAINTAINERS file)
 - "or later" on GPL-2, when we did not have that right

It also allows some Blackfin-specific assembly files to be under a BSD
like license (for people to use them outside of Linux).
Signed-off-by: NRobin Getz <robin.getz@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

These hardware devices are dead and the drivers never cleaned up/merged,
so punt the useless board resource info.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The "TWI_KEYPAD" driver was renamed to "INPUT_PCF8574", so update the
defines in the board resources accordingly.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The sed used to rename the bfin-twi-lcd only replaced the first instance
rather than all which led to the resources not being enabled when the
driver was built as a module.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The BF526-EZBRD has a SST SPI flash on it, not a ST Micro.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The Blackfin SPI driver can be driven by an IRQ now, so declare it in
the board resources.
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Try to keep the naming conventions consistent, so:
	SPI_ADC_BF533 -> BFIN_SPI_ADC
	TWI_LCD       -> BFIN_TWI_LCD
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Blackfin arch: add platform device bfin_mii-bus and KSZ8893M switch driver platform resources to board files
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this
already by stubbing things out
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

[Mike Frysinger <vapier.adi@gmail.com>:
 - setup P_DEFAULT_BOOT_SPI_CS  for every arch based on
   the default bootrom behavior and convert all our boards
   to it
 - revert previous anomaly change ... bf51x is not affected
   by anomaly 05000353]
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Blackfin MUSB has 8 endpoints including ep0 and 8 dma channels not 7
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Cc: Graf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NBryan Wu <cooloney@kernel.org>

these are highly board specific, so putting into generic doesnt make much sense
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NRobin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

The dm9000 driver accepts either 2 or 3 resources to describe the platform
devices. The 2 resources case abuses the ioresource mechanism by passing
ioremap()ed memory through the platform device resources. This patch removes
converts boards that were using it to the 3 resources scheme.

CC: Bryan Wu <cooloney@kernel.org>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

AD7877 use SSEL_2 (P9.9) and IRQ_PF8 (P9.14) on BF527

 - populating JP3 to enable STAMP
 - disable SW11.2 to disconnect SSEL_2/PF12 from Rotary NAND
 - disable SW18.1 to disconnect SSEL_2 from MAX1233 touchscreen chip
Signed-off-by: NBryan Wu <cooloney@kernel.org>

I2C_BOARD_INFO() now sets the type field so no need to set it
separatetly.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Bryan Wu <cooloney@kernel.org>

Signed-off-by: NGrace Pan <grace.pan@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

BF527-EZKit features 16MBit M25P16 flash
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

 - JP3 should be installed for STAMP enable
 - IRQ for twi_keypad driver is IRQ_PF8
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

 - add platform device resources in board files
 - add new bfin_sir.h to each machines
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>