There've been reports [1] about the sysem bell causing a hard
lockup.  My machine was affected as well: any speaker output hung
the machine completely, nothing in the logs, no magic sysrq,
etc., looked like a hardware problem.  Had a closer look on the
issue, and it turned out that the pcspkr module is responsible.
The cause is the bad setup of Timer 2 in the i8253 controller,
which probably hangs the whole PIT controller.

Intel datasheets [2] state that the timer registers are in an
undefined state after reset and they need to be programmed before
enabling the timer. (And enabling without programming the
frequency first doesn't make sense anyway).

I don't know which chipsets are affected (if not all), it also
depends on the BIOS whether it initializes the timer (e.g. to
beep when you start the machine).

The following patch solved the issue on my ICH6 notebook,
couldn't test it with any others, but should be safe to apply.

[1]
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/146151
https://bugs.launchpad.net/ubuntu/+bug/270790
http://ubuntuforums.org/showthread.php?t=227693
http://bugs.gentoo.org/show_bug.cgi?id=222583
https://bugzilla.redhat.com/show_bug.cgi?id=454225

[2]
http://www.intel.com/assets/pdf/datasheet/252516.pdf
http://www.intel.com/assets/pdf/datasheet/301473.pdf
http://www.intel.com/design/chipsets/datashts/29065503.pdfSigned-off-by: NZoltan Devai <zdevai@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The usbtouchscreen module implements a driver for the TSC-10 DM USB
touchscreen controllers, but assumes a 2-byte response for the
CMD_RESET and CMD_RATE commands, when they can be only a single byte
when no EEPROM is connected.

The driver worked with an earlier controller revision, but new
revisions of the controller fail.

It seems the problem is that the early controller had the
SEL4/EEPROM-CS pin high, but the new controller has it down, making
the response different.

Without the fix, the controller would answer the single byte 0x06
(ACK), making the init fail with -ENODEV because buf[1] is 0xFF (as
initialized before).

As the single byte is the only thing we need to check it was ok, there
is no need to verify the second byte.

The [0x15 0x01] case is the NAK [0x15] response for when there is no
data in the EEPROM [bit-0 of second byte set], so I let that be, as I
don't have any controller with an EEPROM.

With this patch, both the earlier and latest controller work the same.

Note: This was previously submited as BUG #11961 [1] on the bugzilla
tracker, but rebased to version 2.6.27.4 and with unnecessary comments
and printk's removed.

[1] http://bugzilla.kernel.org/show_bug.cgi?id=11961Signed-off-by: NNuno Lucas <ntlucas@gmail.com>
Acked-by: NDaniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

There is no reason to limit the GPIO rows to 6 for OMAP2.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The GPIO interrupts are disabled several times after the first key press.
No need to disable - again - the interrupts in the omap_kp_scan_keypad
function on OMAP2.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The appletouch driver has grown up from supporting only a couple of
touchpads into supporting many touchpads, which can have different
number of sensors, different aspect ratios etc.

This patch cleans up the current driver code and makes it easy to
support the features of each different touchpad.

As a side effect, this patch also modifies the 'Y' multiplication factor
of the 'geyser3' and 'geyser4' touchpads (found on Core Duo and Core2
Duo MacBook and MacBook Pro laptops) in order to make the touchpad
output match the aspect ratio of the touchpad (Y factor changed from 43
to 64).

[dtor@mail.ru: make atp_info constant]
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This patch adds a flag to gpio-key driver to turn on the input subsystems
auto repeat feature if needed.
Signed-off-by: NDominic Curran <dcurran@ti.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Review comments were incorporated to improve the driver.

1. Some data was eliminated that was not needed.
2. Renaming of variables for clarity.
3. Removed unneeded type casting.
4. Changed to use dev_err rather than other I/O.
5. Merged together some functions.
6. Added kerneldoc format to functions.
Signed-off-by: NSadanand <sadanan@xilinx.com>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Currently, evdev has working 32bit compatibility and uinput does not. uinput
needs the input_event code that evdev uses, so let's refactor it so it can
be shared.

[dtor@mail.ru: add fix for force feedback compat issues]
Signed-off-by: NPhilip Langdale <philipl@overt.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  libata: fix NCQ devices behind port multipliers
  scsi: make sure that scsi_init_shared_tag_map() doesn't overwrite existing map

For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Right now callers have to check whether scsi_host->bqt is already
set up, it's much cleaner to just have scsi_init_shared_tag_map()
does this check on its own.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (33 commits)
  MIPS: lemote/lm2e: Added io_map_base to pci controller
  MIPS: TXx9: Make firmware parameter passing more robust
  MIPS: Markeins: Remove unnecessary define and cleanup comments, etc.
  MIPS: Markeins: Extract ll_emma2rh_* functions
  MIPS: Markeins: Remove runtime debug prints
  MIPS: EMMA: Fold arch/mips/emma/{common,markeins}/irq*.c into markeins/irq.c
  MIPS: EMMA2RH: Remove emma2rh_gpio_irq_base
  MIPS: EMMA2RH: Remove emma2rh_sw_irq_base
  MIPS: EMMA2RH: Remove emma2rh_irq_base global variable
  MIPS: EMMA2RH: Remove emma2rh_sync on read operation
  MIPS: EMMA: Move <asm/emma2rh> to <asm/emma> dir
  MIPS: EMMA: Move arch/mips/emma2rh/ into arch/mips/emma/
  MIPS: EMMA: Kconfig reorganization
  MIPS: Add CONFIG_CPU_R5500 for NEC VR5500 series processors
  MIPS: RB532: Disable the right device
  MIPS: Add support for NXP PNX833x (STB222/5) into linux kernel
  MIPS: TXx9: CONFIG_TOSHIBA_RBTX4939 spelling
  MIPS: Fix KGDB build error
  INPUT: sgi_btns: Add license specification
  MIPS: IP22: ip22-int.c header file weeding.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: fw-sbp2: fix races
  firewire: fw-sbp2: delay first login to avoid retries
  firewire: fw-ohci: initialization failure path fixes
  firewire: fw-ohci: don't leak dma memory on module removal
  firewire: fix struct fw_node memory leak
  firewire: Survive more than 256 bus resets

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: ASoC: Blackfin: update SPORT0 port selector (v2)
  ALSA: hda - Restore default pin configs for realtek codecs
  sound: use a common working email address
  pci: use pci_ioremap_bar() in sound/

Signed-off-by: NZhang Le <r0bertz@gentoo.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When booting Linux on a txx9 board with VxWorks boot loader, it crashes in
prom_getenv(), as VxWorks doesn't pass firmware parameters in a0-a3 (in my
case, the actual leftover values in these registers were 0x80002000,
0x80001fe0, 0x2000, and 0x20).

Make the parsing of argc, argv, and envp a bit more robust by checking if
argc is a number below CKSEG0, and argv/envp point to CKSEG0.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

These functions are completely ineffective.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove runtime db_* macros as we don't need them any more.  In general,
such helpers are useful for initial porting, but once approved, they are
not indispensable.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Current EMMA2RH irq code is mess.  Before cleaning it up, gather them
in one place as a first step.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Let's use immediate value, instead.  This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Let's use immediate value, instead.  This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Let's use immediate value, instead.  This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It's totally a waste of CPU cycles.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We'll put all EMMA related headers there in the future.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

git mv arch/mips/{emma2rh,emma} and fixups Makefiles.  We'll put all NEC
EMMA series based machines there in the future.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

- Move EMMA related stuff into arch/mips/emma/Kconfig
- Create CONFIG_SOC_EMMA* to handle more EMMA SoCs effectively
- Rename CONFIG_MARKEINS into CONFIG_NEC_MARKEINS
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We already have sufficient infrastructure to support VR5500 and VR5500A
series processors.  Here's a Makefile support to make it selectable by
ports, and enable it for NEC EMMA2RH Markeins board.

This patch also fixes a confused target help, and adds 1Gb PageMask bits
supported by VR5500 and its variants.
Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The following patch add support for the NXP PNX833x SOC.  More
specifically it adds support for the STB222/5 variant. It fixes
the vectored interrupt issue.
Signed-off-by: Ndaniel.j.laird <daniel.j.laird@nxp.com>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix a typo in the comment for the TOSHIBA_RBTX4939 config option
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In file included from include/linux/ptrace.h:49,
                 from arch/mips/kernel/kgdb.c:25:
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:123: error: expected declaration specifiers or '...' before '__s64'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:124: error: expected declaration specifiers or '...' before '__s64'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:126: error: expected declaration specifiers or '...' before '__u32'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:127: error: expected declaration specifiers or '...' before '__u32'
make[1]: *** [arch/mips/kernel/kgdb.o] Error 1
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The SGI Volume Button interface driver uses GPL-only symbols
platform_driver_unregister and platform_driver_register, but
lacks license specification. Thus, when compiled as a module,
this driver cannot be installed. This patch fixes this by
adding the MODULE_LICENSE() specification.
Signed-off-by: NDmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The following functions

disable_local1_irq()
disable_local2_irq()
disable_local3_irq()

are needlessly defined global, so make them static. While at it, fix a
whitespace error in the same file.
Signed-off-by: NDmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add smc91x platform device to RBTX4939 board and some hacks for big endian.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add sysfs interface for 7 segment LED and implement access routine for
RBTX4939.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add au1xmmc platform data for PB1200/DB1200 boards and wire up the 2 SD
controllers for them.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch sets the correct interrupt status and level
in order to get the CompactFlash adapter working.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>