This device needs the quirk as well.
Tested-by: NKevin Fenzi <kevin@scrye.com>
Signed-off-by: NAdel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This device needs the quirk as well.
Signed-off-by: NAdel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

There is a second mouse sharing the same vendor strings but different IDs.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This mouse keeps disconnecting in runlevel 3. It needs the ALWAYS_POLL quirk.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Enable the always-poll quirk for Elan Touchscreens found on some recent
Samsung laptops.

Without this quirk the device keeps disconnecting from the bus (and is
re-enumerated) unless opened (and kept open, should an input event
occur).

Note that while the device can be run-time suspended, the autosuspend
timeout must be high enough to allow the device to be polled at least
once before being suspended. Specifically, using autosuspend_delay_ms=0
will still cause the device to disconnect on input events.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This device generates ABS_Z and ABS_RX events instead of ABS_X and
ABS_Y.
Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

I am using a USB keyborad that give me "usb_submit_urb(ctrl) failed: -1" error
when I plugin it.  and I need to wait for 10s for this device to be ready.

By adding this quirks, the usb keyborad is usable right after plugin
Signed-off-by: NWangzhao Cai <microcaicai@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This device generates ABS_Z and ABS_RX events instead of ABS_X and
ABS_Y.
Signed-off-by: NWen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This driver adds support for USB controlled led panels that exists in
MSI GT683R laptop
Signed-off-by: NJanne Kanniainen <janne.kanniainen@gmail.com>
Reviewed-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

These device needs to be added to the quirks list with HID_QUIRK_NOGET,
otherwise they will reset upon receiving the get input report requests.
Signed-off-by: NJohn Sung <penmount.touch@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The device which identifies itself as a "USB Keykoard" (no typo) with VID:PID
1a2c:0023 does not seem to be handling the reports initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the kernel
when connected, and a delay before its initialization.  This patch adds the
quirk for this device, which causes the delay to disappear.

[jkosina@suse.cz: remove superfluous comment and fix ordering]
Signed-off-by: NDaniel Kamil Kozar <dkk089@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This touchpad seriously dislikes init reports, not only timeing out, but
also refusing to work after this.

Cc: stable@vger.kernel.org
Reported-and-tested-by: NVincent Fortier <th0ma7@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

There is timeout error during initialization:
kernel: [   11.733104] hid-multitouch 0003:1870:0110.0001: usb_submit_urb(ctrl) failed: -1
kernel: [   11.734093] hid-multitouch 0003:1870:0110.0001: timeout initializing reports

Adding quirk HID_QUIRK_NO_INIT_REPORTS can solve the problem.
Signed-off-by: NYufeng Shen <miletus@chromium.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

[jkosina@suse.cz: refresh to apply after SIS quirk merging]
Signed-off-by: NEmanuel Krenz <emanuelkrenz@web.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add Synaptics HD touchscreen(06cb:1ac3) to no init report quirk
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add Synaptics HD touchscreen(06cb:0ac3) to no init report quirk.
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

USB_VENDOR_ID_SIS and USB_VENDOR_ID_SIS2_TOUCH are identical,
so refine the code and merge the quirks.
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add support for SiS multitouch panels.
Signed-off-by: NForest Bond <forest.bond@rapidrollout.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

BugLink: http://bugs.launchpad.net/bugs/1180881

This device needs to be added to the quirks list with HID_QUIRK_NO_INIT_REPORTS,
otherwise it causes 10 seconds timeout during report initialization.

[12431.828467] hid-multitouch 0003:0457:1013.0475: usb_submit_urb(ctrl) failed: -1
[12431.828507] hid-multitouch 0003:0457:1013.0475: timeout initializing reports
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

BugLink: http://bugs.launchpad.net/bugs/1180881

Synaptics large touchscreen doesn't support some of the report request
while initializing. The unspoorted request will make the device unreachable,
and will lead to the following usb_submit_urb() function call timeout.
So, add the IDs into HID_QUIRK_NO_INIT_REPORTS quirk.
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The DuoSense touchscreen device causes a 10 second timeout. This fix
removes the delay.
Signed-off-by: NVasily Titskiy <qehgt0@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fix build problem caused by typo introduced by 620ae90e
("HID: usbhid: quirk for MSI GX680R led panel").

Reported-by: fengguang.wu@intel.com
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This keyboard backlight device causes a 10 second delay to boot.  Add it
to the quirk list with HID_QUIRK_NO_INIT_REPORTS.

This fixes Red Hat bugzilla https://bugzilla.redhat.com/show_bug.cgi?id=907221

Cc: stable@vger.kernel.org
Signed-off-by: NJosh Boyer <jwboyer@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This device needs to be added to the quirks list with HID_QUIRK_NO_INIT_REPORTS,
otherwise it causes 10 seconds timeout during report initialization.

This fixes Red Hat bugzilla https://bugzilla.redhat.com/show_bug.cgi?id=806587

Cc: stable@vger.kernel.org
Signed-off-by: NJosh Boyer <jwboyer@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Patch to add the Formosa Industrial Computing, Inc. Infrared Receiver
[IR605A/Q] to hid-ids.h and hid-quirks.c.  This IR receiver causes about a 10
second timeout when the usbhid driver attempts to initialze the device.  Adding
this device to the quirks list with HID_QUIRK_NO_INIT_REPORTS removes the
delay.
Signed-off-by: NNicholas Santos <nicholas.santos@gmail.com>
[jkosina@suse.cz: fix ordering]
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The USB recovery mode present in i.MX23 ROM emulates USB HID.  It needs this
quirk to behave properly.

Even if the official branding of the chip is Freescale i.MX23, I named it
Sigmatel STMP3780 since that's what the chip really is and it even reports
itself as STMP3780.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch adds support to Novatec wireless mouse (device ID 0603:1602).
Fixes bug https://bugzilla.kernel.org/show_bug.cgi?id=47031Signed-off-by: NMarco Biscaro <marcobiscaro2112@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Without this, the device is blocked in dmesg at:
hid-multitouch 0003:25AA:8883.000X: usb_submit_urb(ctrl) failed: -1
hid-multitouch 0003:25AA:8883.000X: timeout initializing reports
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

For some reason, we had two IDs for the QUANTA 3001 touchscreen controller,
one USB_DEVICE_ID_QUANTA_OPTICAL_TOUCH_3001 and one
USB_DEVICE_ID_PIXART_IMAGING_INC_OPTICAL_TOUCH_SCREEN. As this has caused
confusion, remove USB_DEVICE_ID_PIXART_IMAGING_INC_OPTICAL_TOUCH_SCREEN
completely, and fix places where it was used to refer to
USB_DEVICE_ID_QUANTA_OPTICAL_TOUCH_3001.
Signed-off-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch (as1603) adds a NOGET quirk for the Eaton Ellipse MAX UPS
device.  (The USB IDs were already present in hid-ids.h, apparently
under a different name.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NLaurent Bigonville <l.bigonville@edpnet.be>
CC: <stable@vger.kernel.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The USB recovery mode present in i.MX28 ROM emulates USB HID.
It needs this quirk to behave properly.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Chen Peter <B29397@freescale.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Kosina <jkosina@suse.cz>
[jkosina@suse.cz: fix alphabetical ordering]
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The Sennheiser BTD500USB composit device requires the
HID_QUIRK_NOGET flag to be set for working proper. Without the
flag the device crashes during hid intialization.
Signed-off-by: NFrank Kunz <xxxxxmichl@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add support for Waltop Sirius Battery Free Tablet. VisTablet Muse and Princeton
PTB-S1BK are other possible names of this tablet.
Signed-off-by: NNikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Some quanta devices do not like to be polled for reports
descriptors, thus this quirk.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@enac.fr>
Acked-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add support for three KYE tablets: EasyPen i405X, MousePen i608X, EasyPen M610X.
Update Kconfig entry accordingly, remove EXPERT dependency.
Signed-off-by: NNikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch (as1531) adds a NOGET quirk for the Slim+ keyboard marketed
by AIREN.  This keyboard seems to have a lot of bugs; NOGET works
around only one of them.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: Nokias <d.okias@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

CH Fighterstick requires HID_QUIRK_NOGET as many other CH devices do. This
patch adds device id for Fighterstick and adds necessary line to HID quirk
list.
Signed-off-by: NVille Ranki <ville.ranki@iki.fi>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add quirk for the Trio Linker Plus II - the adapter supports several
controllers simultaneously, generating a new HID entry for each connected
device.
Signed-off-by: NIgnaz Forster <ignaz.forster@gmx.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch modifies hid-multitouch driver for supporting PixArt optical touch
screen.  Because of the device does not have to set initial report, we apply
"HID_QUIRK_NO_INIT_REPORTS" quirk and add the device into hid_blacklist[]
Signed-off-by: NAaron Tian <aaron_tian@pixart.com.tw>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>