Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 19 2月, 2012 4 次提交
    • M
      [SCSI] pm8001: deficient responses to IO_XFER_ERROR_BREAK and IO_XFER_OPEN_RETRY_TIMEOUT · 5954d738
      由 Mark Salyzyn 提交于 
      IO_XFER_ERROR_BREAK and IO_XFER_OPEN_RETRY_TIMEOUT are deficient of the
required actions as outlined in the programming manual for the pm8001. Due to
the overlapping code requirements of these recovery responses, we found it
necessary to bundle them together into one patch.

When a break is received during the command phase (ssp_completion), this is a
result of a timeout or interruption on the bus. Logic suggests that we should
retry the command.

When a break is received during the data-phase (ssp_event), the task must be
aborted on the target or it will retain a data-phase lock turning the target
reticent to all future media commands yet will successfully respond to TUR,
INQUIRY and ABORT leading eventually to target failure through several
abort-cycle loops.

The open retry interval is exceedingly short resulting in occasional target
drop-off during expander resets or when targets push-back during bad-block
remapping. Increased effective timeout from 130ms to 1.5 seconds for each try
so as to trigger after the administrative inquiry/tur timeout in the scsi
subsystem to keep error-recovery harmonics to a minimum.

When an open retry timeout event is received, the action required by the
targets is to issue an abort for the outstanding command then logic suggests
we retry the command as this state is usually an indication of a credit block
or busy condition on the target.

We hijacked the pm8001_handle_event work queue handler so that it will handle
task as an argument instead of device for the workers in support of the
deferred handling outlined above.

Moderate to Heavy bad-path testing on a 2.6.32 vintage kernel, compile-testing
on scsi-misc-2.6 kernel ...
Signed-off-by: NMark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
      5954d738
    • M
      [SCSI] pm8001: Add FUNC_GET_EVENTS · d95d0001
      由 Mark Salyzyn 提交于 
      Jack noticed I dropped a patch fragment associated with a flags automatic
variable in mpi_set_phys_g3_with_ssc (ooops) and that the pre-emptive locking
that piggy-backed this patch was not in-fact necessary because of underlying
atomic accesses to the hardware. Here is the updated patch fixing these two
issues.

The pm8001 driver is missing the FUNC_GET_EVENTS handler in the phy control
function. Since the pm8001_bar4_shift function was not designed to be called
at runtime, added locking surrounding the adjustment for all accesses.
Signed-off-by: NMark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
      d95d0001
    • M
      [SCSI] pm8001: fix lockup on phy_control hard reset. · 5c4fb76a
      由 Mark Salyzyn 提交于 
      pm8001_phy_control PHY_FUNC_HARD_RESET locks up on second try via
smp_phy_control because response HW_EVENT_PHY_START_STATUS fails to complete
previous command. The PM8001F_RUN_TIME flag is not treated as a bit, but a
state in all readers, yet once we are operational or in the run time state,
the flags use a bit-set operation.
Signed-off-by: NMark Salyzyn <mark_salyzyn@xyratex.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
      5c4fb76a
    • O
      [SCSI] st: implement PM · 46a243f7
      由 Oliver Neukum 提交于 
      This implements basic power management for SCSI tapes.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Acked-by: NKai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>
      46a243f7
  3. 18 2月, 2012 15 次提交
  5. 13 2月, 2012 1 次提交
  7. 22 1月, 2012 2 次提交
  9. 16 1月, 2012 18 次提交