If a tuning command times out, the card could still be processing it, which
will cause problems for recovery. The eMMC specification says that CMD12
can be used to stop CMD21, so add a function that does that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add definitions relating to Command Queuing.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The only time the driver sleeps expecting to be woken upon the arrival of
a new request, is when the dispatch queue is empty. The only time that it
is known whether the dispatch queue is empty is after NULL is returned
from blk_fetch_request() while under the queue lock.

Recognizing those facts, simplify the synchronization between the queue
thread and the request function. A couple of flags tell the request
function what to do, and the queue lock and barriers associated with
wake-ups ensure synchronization.

The result is simpler and allows the removal of the context_info lock.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NHarjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

I've had it with this code now.

The packed command support is a complex hurdle in the MMC/SD block
layer, around 500+ lines of code which was introduced in 2013 in

commit ce39f9d1 ("mmc: support packed write command for eMMC4.5
devices")
commit abd9ac14 ("mmc: add packed command feature of eMMC4.5")

...and since then it has been rotting. The original author of the
code has disappeared from the community and the mail address is
bouncing.

For the code to be exercised the host must flag that it supports
packed commands, so in mmc_blk_prep_packed_list() which is called for
every single request, the following construction appears:

u8 max_packed_rw = 0;

if ((rq_data_dir(cur) == WRITE) &&
    mmc_host_packed_wr(card->host))
        max_packed_rw = card->ext_csd.max_packed_writes;

if (max_packed_rw == 0)
    goto no_packed;

This has the following logical deductions:

- Only WRITE commands can really be packed, so the solution is
  only half-done: we support packed WRITE but not packed READ.
  The packed command support has not been finalized by supporting
  reads in three years!

- mmc_host_packed_wr() is just a static inline that checks
  host->caps2 & MMC_CAP2_PACKED_WR. The problem with this is
  that NO upstream host sets this capability flag! No driver
  in the kernel is using it, and we can't test it. Packed
  command may be supported in out-of-tree code, but I doubt
  it. I doubt that the code is even working anymore due to
  other refactorings in the MMC block layer, who would
  notice if patches affecting it broke packed commands?
  No one.

- There is no Device Tree binding or code to mark a host as
  supporting packed read or write commands, just this flag
  in caps2, so for sure there are not any DT systems using
  it either.

It has other problems as well: mmc_blk_prep_packed_list() is
speculatively picking requests out of the request queue with
blk_fetch_request() making the MMC/SD stack harder to convert
to the multiqueue block layer. By this we get rid of an
obstacle.

The way I see it this is just cruft littering the MMC/SD
stack.

Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Maya Erez <qca_merez@qca.qualcomm.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The void (*pre_req) callback in the struct mmc_host_ops vtable
is passing an argument "is_first_req" indicating whether this is
the first request or not.

None of the in-kernel users use this parameter: instead, since
they all just do variants of dma_map* they use the DMA cookie
to indicate whether a pre* callback has already been done for
a request when they decide how to handle it.

Delete the parameter from the callback and all users, as it is
just pointless cruft.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch removed the meaningless value. Instead, use the cookie's enum
values for executing correctly.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This is in preparation for restoring saved tuning parameters
when resuming the TMIO driver.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There were several instances of code using the
enum mmc_blk_status by arbitrarily converting it to an int and
throwing it around to different functions. This makes the code
hard to understand to may give rise to strange errors.

Especially the function prototype mmc_start_req() had to be
modified to take a pointer to an enum mmc_blk_status and the
function pointer .err_check() inside struct mmc_async_req
needed to return an enum mmc_blk_status.

In every case: instead of assigning the block layer error code
to an int, use the enum, also change the signature of all
functions actually passing this enum to use the enum.

To make it possible to use the enum everywhere applicable, move
it to <linux/mmc/core.h> so that all code actually using it can
also see it.

An interesting case was encountered in the MMC test code which
did not return a enum mmc_blk_status at all in the .err_check
function supposed to check whether asynchronous requests worked
or not: instead it returned a normal -ERROR or even the test
frameworks internal error codes.

The test code would also pass on enum mmc_blk_status codes as
error codes inside the test code instead of converting them
to the local RESULT_* codes.

I have tried to fix all instances properly and run some tests
on the result.

Cc: Chunyan Zhang <zhang.chunyan@linaro.org>
Cc: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add new helper API mmc_can_gpio_cd for slot-gpio to make
host drivers know whether it supports gpio card detect.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The core uses it for polling. Give drivers a proper define handle this
case like for other response types.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

A host controller driver exposes its capability using caps flag
MMC_CAP_CMD_DURING_TFR. A driver with that capability can accept requests
that are marked mrq->cap_cmd_during_tfr = true. Then the driver informs the
upper layers when the command line is available for further commands by
calling mmc_command_done(). Because of that, the driver will not then
automatically send STOP commands, and it is the responsibility of the upper
layer to send a STOP command if it is required.

For requests submitted through the mmc_wait_for_req() interface, the caller
sets mrq->cap_cmd_during_tfr = true which causes mmc_wait_for_req() in fact
not to wait. The caller can then send commands that do not use the data
lines. Finally the caller can wait for the transfer to complete by calling
mmc_wait_for_req_done() which is now exported.

For requests submitted through the mmc_start_req() interface, the caller
again sets mrq->cap_cmd_during_tfr = true, but mmc_start_req() anyway does
not wait. The caller can then send commands that do not use the data
lines. Finally the caller can wait for the transfer to complete in the
normal way i.e. calling mmc_start_req() again.

Irrespective of how a cap_cmd_during_tfr request is started,
mmc_is_req_done() can be called if the upper layer needs to determine if
the request is done. However the appropriate waiting function (either
mmc_wait_for_req_done() or mmc_start_req()) must still be called.

The implementation consists primarily of a new completion
mrq->cmd_completion which notifies when the command line is available for
further commands. That completion is completed by mmc_command_done().
When there is an ongoing data transfer, calls to mmc_wait_for_req() will
automatically wait on that completion, so the caller does not have to do
anything special.

Note, in the case of errors, the driver may call mmc_request_done() without
calling mmc_command_done() because mmc_request_done() always calls
mmc_command_done().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Dwmmc host controller may in unknown state when entering kernel boot. One
example is when booting from eMMC, bootloader need initialize MMC host
controller into some state so it can read. In order to make sure MMC host
controller in a clean initial state, this reset support is added.

With this patch, a 'resets' property can be added into dw_mmc device
tree node. The hardware logic is: dwmmc host controller IP receives a reset
signal from a 'reset provider' (eg. power management unit). The 'resets'
property points to this reset signal. So, during dwmmc driver probe,
it can use this signal to reset itself.

Refer to [1] for more information.

[1] Documentation/devicetree/bindings/reset/reset.txt
Signed-off-by: NGuodong Xu <guodong.xu@linaro.org>
Signed-off-by: NXinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The SD Status register contains several important fields related to the
SD Card proprietary features.
Those fields may be used by user space applications for vendor specific
usage.
None of those fields are exported today by the driver to user space.
In this patch, we are reading the SD Status register and exporting
(using MMC_DEV_ATTR) the SD Status register to the user space.
Signed-off-by: NUri Yanai <uri.yanai@sandisk.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The driver already supports the bcm4339 chipset but only for the variant
that shares the same modalias as the bcm4335, ie. sdio:c00v02D0d4335.
It turns out that there are also bcm4339 devices out there that have a
more distiguishable modalias sdio:c00v02D0d4339.
Reported-by: NSteve deRosier <derosier@gmail.com>
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Host drivers which needs to valdiate for non-supported MMC
commands and returnn error code for such requests.

To improve and simplify the behaviour, let's invent MMC_CAP2_NO_MMC
which these host drivers can set to tell the mmc core to skip sending MMC
commands during card initialization.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove the quirks flag. (DW_MCI_QUIRK_BROKEN_DTO)
For removing this, enabled the dto_timer by defaults.
It doesn't see any I/O performance degression.
In future, dwmmc controller should not use the quirks flag.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There are host drivers which needs to valdiate for non-supported SD
commands and returnn error code for such requests.

To improve and simplify the behaviour, let's invent MMC_CAP2_NO_SD
which these host drivers can set to tell the mmc core to skip sending SD
commands during card initialization.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Certain Hynix eMMC 4.41 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.

As some of the other features like BKOPs/Cache/Sanitize are dependent on
HPI feature, those features would also get disabled if HPI is disabled.
Signed-off-by: NPratibhasagar V <pratibha@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
[gdavis: Forward port and cleanup]
Signed-off-by: NGeorge G. Davis <george_davis@mentor.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Controllers use data strobe line to latch data from devices
under hs400 mode, but not for cmd line. So since emmc 5.1, JEDEC
introduces enhanced strobe mode for latching cmd response from
emmc devices to host controllers. This new feature is optional,
so it depends both on device's cap and host's cap to decide
whether to use it or not.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NDouglas Anderson <dianders@chromium.org>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch introduce mmc-hs400-enhanced-strobe for platforms
which want to enable enhanced strobe function from DT if the
mmc host controller claims to support enhanced strobe.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: NDouglas Anderson <dianders@chromium.org>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Re-tuning is not possible when switched to the RPMB
partition.  However re-tuning should not be needed
if re-tuning is done immediately before switching,
a small set of operations is done, and then we
immediately switch back to the main partition.

To ensure that re-tuning can't be done for a short
while, add a facility to "pause" re-tuning.

The existing facility to hold / release re-tuning
is used but it also flags re-tuning as needed to cause
re-tuning before the next command (which will be the
switch to RPMB).

We also need to "unpause" in the recovery path, which
is catered for by adding it to mmc_retune_disable().
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This adds support for the 4356-sdio wireless chip.
Signed-off-by: NChristian Daudt <csd@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

A few SH boards include the file but don't make use of it (no named
interrupts). The SDHI code removed support for this feature as well.
So, drop the references and ultimately remove the unneeded file.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NRich Felker <dalias@libc.org>
Acked-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There is no reason to have a public and private header file. Merge them
into a private one, so looking up symbols is less confusing.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

EVENT_XFER_ERROR isn't been used now, so it can be removed.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Try to fix the warning reported by:
scripts/kernel-doc -man -v include/linux/mmc/dw_mmc.h > /dev/null

warning: No description found for parameter 'irq_lock'
warning: No description found for parameter 'stop_abort'
warning: No description found for parameter 'prev_blksz'
warning: No description found for parameter 'timing'
warning: No description found for parameter 'ring_size'
warning: No description found for parameter 'dms'
warning: No description found for parameter 'phy_regs'
warning: No description found for parameter 'fifoth_val'
warning: No description found for parameter 'vqmmc_enabled'
warning: No description found for parameter 'cmd11_timer'
warning: Excess struct/union/enum/typedef member 'card_tasklet'
description in 'dw_mci'
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

While here, refactor the comments so that they are before the
declaration they are referring to.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Based on work by Shinobu Uehara and Ben Dooks. This adds the voltage
switch operation needed for all UHS-I modes, but not the tuning needed
for SDR-104 which will come later.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

dw_mmc already use mmc_of_parse to get "broken-cd" property,
but it considered "broken-cd" to be a quirk in its driver. We
don't need this quirk here, and just take what we need from
mmc->caps.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch removes struct block_settings since
it's never used anywhere.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some of the indentation made the code awful to read. Fix that. Also,
introduce defines instead of magic hex values. Note that this includes
one change: We mask out know 0xff instead of 0x1ff. But 0x100 has always
been the clock enable bit. It doesn't make any sense to set it depending
on the clock calculation. Update copyright notices, too. I'll be working
on those files some more in the future.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It's not set to MMC_DATA_STREAM anywhere.
It seems that it had been used with CMD11/CMD20.
But according to Spec, CMD11/CMD20 are obsolete command.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Removed the unused quirks. These quirks don't used anywhere.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The dw_mmc driver stores the physical address of the MMIO registers
in a pointer, which requires the use of type casts, and is actually
broken if anyone ever has this device on a 32-bit SoC in registers
above 4GB. Gcc warns about this possibility when the driver is built
with ARM LPAE enabled:

mmc/host/dw_mmc.c: In function 'dw_mci_edmac_start_dma':
mmc/host/dw_mmc.c:702:17: warning: cast from pointer to integer of different size
  cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
                 ^
mmc/host/dw_mmc-pltfm.c: In function 'dw_mci_pltfm_register':
mmc/host/dw_mmc-pltfm.c:63:19: warning: cast to pointer from integer of different size
  host->phy_regs = (void *)(regs->start);

This changes the code to use resource_size_t, which gets rid of the
warning, the bug and the useless casts.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch introduce a new MMC_CAP2_NO_SDIO cap used to tell the mmc
core to not send SDIO specific commands.
Signed-off-by: NCarlo Caione <carlo@endlessm.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Instead of checking for "#ifdef" directly in the code, let's invent a pair
of mmc core functions to deal with register/unregister the MMC PM notifier
block. Implement stubs for these functions when CONFIG_PM_SLEEP is unset,
as in that case the PM notifiers isn't used.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.

in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: NChaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK31xx
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This adds logic to the MMC core to set VQMMC.  This is expected to be
called by MMC drivers like dw_mmc as part of (or instead of) their
start_signal_voltage_switch() callback.

A few notes:

* When setting the signal voltage to 3.3V we do our best to make VQMMC
  and VMMC match.  It's been reported that this makes some old cards
  happy since they were tested back in the day before UHS when VQMMC
  and VMMC were provided by the same regulator.  A nice side effect of
  this is that we don't end up on the hairy edge of VQMMC (2.7V),
  which some EEs claim is a little too close to the minimum for
  comfort.
  This is done in two steps. At first we try to find a VQMMC within
  a 0.3V tolerance of VMMC and if this is not supported by the
  supplying regulator we try to find a suitable voltage within the
  whole 2.7V-3.6V area of the spec.

* The two step approach is currently necessary, as the used
  regulator_set_voltage_triplet(min, target, max) uses a simple
  implementation that just tries two basic steps:
	regulator_set_voltage(target, max);
	regulator_set_voltage(min, target);
  So with only one step with 2.7-3.6V borders, if a suitable voltage
  is a bit below VMMC, we would directly get the lowest 2.7V
  which some boards (like Rockchips) don't like at all.

* When setting the signal voltage to 1.8V or 1.2V we aim for that
  specific voltage instead of picking the lowest one in the range.

* We very purposely don't print errors in mmc_regulator_set_vqmmc().
  There are cases where the MMC core will try several different
  voltages and we don't want to pollute the logs.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>