"ret" has already been checked at this point, and we don't need to check
it again.  This was left around from a previous patch 49d750ca
"wl12xx: 1281/1283 support - New radio structs and functions".
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Delete the global wl->vif (and the checks on it),
so multiple vifs could be added.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Enter forced psm when changing fw, in order to make the
sta a bit more disconnection-persistent.
(DPM doesn't know about the incoming recovery, so it
won't enter psm by itself)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wl12xx uses different fw for single-role and multi-role
scenarios (due to lack of space, some of the fw advanced
features are disabled in the multi-role fw).

Add checks on add_interfae and remove_interface in order
to determine whether a fw switch is needed (and initiate
recovery in this case).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

A special PLT firmware is used for calibration.

Add multiple fw support by introducing a new fw_type member,
representing the currently saved fw (the actual fw state
can be determined by wl->state).
Signed-off-by: NGery Kahn <geryk@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Split scan allows the FW to schedule other activities
during a scan which may be a long operation. This is
achieved by setting a trigger TID to ANY_TID and a scan
trigger timeout other than 0. The default one is set to 50ms.
Signed-off-by: NEyal Shapira <eyal@wizey.com>
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Increase max scan IEs to allow big probe-req frames

Report a correct max-length for the scan IEs we can support, according
to the now larger size of the probe-req template.
Signed-off-by: NIdo Reis <idor@ti.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

By allowing hw scan while idle, we no longer
need the redundant ROC/CROC that are done
on idle off/on, which helps simplifying the
state machine of the driver.

This way, we can also allow scanning while
there is an ongoing sched scan (otherwise,
we won't be able to ROC on idle-off)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We have to configure arp filtering only after the role was
started, so move the BSS_CHANGED_ARP_FILTER handling after
the join.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This reverts commit e5e2f24b.

The encryption consideration on auto-arp configuration,
along with a fw fix, seem to resolve the crashes that
occured when auto-arp was enabled, so we can re-enable it now.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When configuring the arp response template,
and encryption is enabled, we should add some
space and set the protected flag bit in the fc.

In order to track the encryption type, set
wlvif->encryption_type when setting an encryption key,
and reconfigure the arp response. Clear this field on
wl1271_join, as keys have to be re-configured
anyway after a join command.

Similarly, track whether QoS is configured.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

For certain WiFi certification tests forcing PS
is necessary. Since DPS is now enabled in the FW
and this can't be achieved by using netlatency
this required a new config option.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Added ability to set different wake up conditions for suspend/resume.
Set default values to wake up every 3 DTIMs while suspended
and every 1 DTIM while resumed
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

new params were added to the coex params.
Add them with default value of 0.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

New FW reports usage of short GI as a rate class index. Check for
this rate and set the IEEE80211_TX_RC_SHORT_GI if used.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

WLVIF_FLAG_PSM turned to WLVIF_FLAG_IN_AUTO_PS which
marks that this vif is in AUTO PS.

WLVIF_FLAG_PSM_REQUESTED is not required as mac80211
calls op_config with CONF_PS after association.

wl12xx_config_vif() handling of CONF_PS was simplified
and cleaned up.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

cleanup 2 unused parameters of wl1271_ps_set_mode
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

FW now supports dynamic PS so we don't need to use mac80211 support.
FW will go to PSM after a specified timeout with no Rx/Tx traffic.
- Changed FW API to include new PS mode (AUTO_MODE) and including timeout parameter
- The default PS mode would be dynamic PS
- Default timeout is 100ms (same as it used to be in mac80211)
- Avoid using mac80211 APIs to disable/enable dynamic PS as we're not
using mac80211 PS control anymore.
- COEX is handled by the FW while in dynamic PS so removed
handling of SOFT_GEMINI
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Removal of PS management code from the driver as PS
is handled by the FW (dynamic PS)
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Update enums/structs to the new fw api.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The ACX_TSF_INFO command now takes role_id as param.
change the struct accordingly, and pass the wlvif
to the wl1271_acx_tsf_info() function.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Use device role for scans when the sta is not
associated.

sched_scan is used only when the sta is
not associated, and thus should use
the dev role (instead of sta role).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The set_template commands now takes the role_id as
parameter.

Usually, we'll use the vif's main role_id.
However, sometimes we'll want to use
wlvif->dev_role_id instead of wlvif->role_id,
so pass the wanted role_id as param.

Update WL127X_FW_NAME/WL128X_FW_NAME.

(This commit starts a series of fw update patches,
and changes the start() callback to return an error
in order to prevent the use of the driver during the
transition. This change will be reverted in the
last patch of series)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

with the new auth/assoc redesign, we get CHANGED_BSSID
indication before CHANGED_ASSOC indication, while our
CHANGED_BSSID handling block assumes we are already
associated.

Fix it by checking we are either in ibss mode, or
already associated.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Fix a copy and paste bug in the MODULE_PARAM_DESC for fwlog.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add support for two MAC addresses.  If the NVS has a valid MAC
address, that takes precedence and we use two sequential address
starting from the one specified.

If the NVS doesn't contain a valid MAC address (ie. if it is set to
00:00:00:00:00:00), we check if the HW PG version in use has the
BD_ADDR written in the fuse ROM.  If it does, we read it and derive
the two subsequent addresses for WLAN.

During production, 3 addresses are reserved per device.  The first for
Bluetooth (burnt in the fuse ROM) and the following two for WLAN.

This patch has some code by Igal and Arik (squashed from internal
patches).
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In order to read the MAC addresses from the fuse ROM, we need to know
the chip ID and the HW PG version.  We need to know the MAC address
during probe, because that's when we register our HW with mac80211.

To prepare for that, this patch reads the chip ID and HW PG version
during probe instead of doing it at boot time.  We power the chip on
briefly in order to do that.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In some cases a race condition can happen if we don't cancel any
pending ELP work before stopping PLT.  With this commit we cancel ELP
work and clear the wl->flags bitmask.  Also clean up the wl elements
after powering off.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The interrupt threaded handler exits immediately if the driver's state
is WL1271_STATE_OFF. As a result, the interrupt status is not read. If
the interrupt is level triggered, it will be fired again.

Fix this by disabling interrupts before setting the state to OFF.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When stopping plt, the chip is powered off before all current work items
are flushed and interrupts are disabled. This might introduce a race in
which the driver tries to communicate with a powered off chip.

Fix this by powering off the device only after interrupts are disabled
and all work items are flushed.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

__wl1271_plt_stop is called from both wl1271_plt_stop and
wl1271_unregister_hw. While wl1271_plt_stop acquires a mutex,
wl1271_unregister_hw does not.

Fix this by calling wl1271_plt_stop instead of __wl1271_plt_stop from
wl1271_unregister_hw.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The sched_scan_(stop|start) ops fails to check for WL1271_STATE_OFF.
This can lead to a race where the driver tries to access the HW
while it's off.

Fix this by checking for WL1271_STATE_OFF before accessing the HW.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current wl1271_dev_notify implementation sets the
new operstate to all associated stations (while only
a specific vif was changed).

Until we'll have a method to get the actual vif from
the given dev, check the current operstate of each vif.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When removing a sta/ibss role, the device role has to
stopped (and disabled) as well.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

dev_role_id only indicates whether the dev role
is enabled, not started (e.g. on IBSS merge,
the device role is enabled, but not started).

Checking for any role in ROC (in order to determine
whether dev role was started) is wrong as well,
especially in multi-vif env.

Check for started dev role only by checking the dev_hlid.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This flag should be set per-vif, rather than globally.

Rename the flag to indicate IN_USE (rather than IDLE), as
in the default configuration (i.e. flag is clear) the vif
should be idle.

Change all the bit operations (and elp conditions) appropriately.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Since the conf_tx callback passes the vif as param,
we must have been added first (and mac80211 verifies it).

Remove the handling of such case.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Implement the change_interface callback by simply removing the
current vif and adding a new one after updating the vif type.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>