Replace the two separate calls for clearing the irqchip's chained handler
and its data with a single irq_set_chained_handler_and_data() call.
Signed-off-by: NMartin Kaiser <martin@kaiser.cx>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The Armada 37xx driver always initializes the IRQ base to 0, hence the
subtraction is a no-op. Remove the subtraction and thereby the last user
of struct gpio_chip's .irq_base field.

Note that this was also actually a bug and only worked because of the
above assumption. If the IRQ base had been dynamically allocated, the
subtraction would've caused the wrong mask to be generated since the
struct irq_data.hwirq field is an index local to the IRQ domain. As a
result, it should now be safe to also allocate this chip's IRQ base
dynamically, unless there are consumers left that refer to the IRQs by
their global number.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

OPEN_DRAIN and OPEN_SOURCE flags only affect the way we drive a GPIO
line, so they only make sense for output mode. Just as we only allow
input mode for event handle requests, don't allow passing open-drain
and open-source flags for any other mode than explicit output.
Signed-off-by: NBartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There's no need to check the validity of handle request flags more
than once, right after copying the data from user. Move the check
out of the for loop and simplify the error path by bailing out before
allocating any resources.
Signed-off-by: NBartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

SPI-attached GPIO controllers typically read out all inputs in one go.
If callers desire the values of multipe inputs, ideally a single readout
should take place to return the desired values.  However the current
driver API only offers a ->get callback but no ->get_multiple (unlike
->set_multiple, which is present).  Thus, to read multiple inputs, a
full readout needs to be performed for every single value (barring
driver-internal caching), which is inefficient.

In fact, the lack of a ->get_multiple callback has been bemoaned
repeatedly by the gpio subsystem maintainer:
http://www.spinics.net/lists/linux-gpio/msg10571.html
http://www.spinics.net/lists/devicetree/msg121734.html

Introduce the missing callback.  Add corresponding consumer functions
such as gpiod_get_array_value().  Amend linehandle_ioctl() to take
advantage of the newly added infrastructure.  Update the documentation.

Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

A common idiom is to assign a value to a bit with:

    if (value)
        set_bit(nr, addr);
    else
        clear_bit(nr, addr);

Likewise common is the one-line expression variant:

    value ? set_bit(nr, addr) : clear_bit(nr, addr);

Commit 9a8ac3ae ("dm mpath: cleanup QUEUE_IF_NO_PATH bit
manipulation by introducing assign_bit()") introduced assign_bit()
to the md subsystem for brevity.

Make it available to others, specifically gpiolib and the upcoming
driver for Maxim MAX3191x industrial serializer chips.

As requested by Peter Zijlstra, change the argument order to reflect
traditional "dst = src" in C, hence "assign_bit(nr, addr, value)".

Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Neil Brown <neilb@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Acked-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLukas Wunner <lukas@wunner.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Some platforms require reset to be released to allow register
access.
Signed-off-by: NAlan Tull <atull@kernel.org>
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>
[Added DT bindings oneliner for standard reset binding]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Use the of_device_get_match_data() helper instead of open coding.
Note that the gpio-rcar driver is used with DT only, so there's always a
valid match.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Currently calls to:
gpiod_direction_output_raw()
gpiod_set_raw_value()
gpiod_set_raw_array_value()
gpiod_set_raw_value_cansleep()
gpiod_set_raw_array_value_cansleep()

Respect that we do not want to invert the value written, but will
still apply special open drain/open source semantics if the line has
an open drain/open source flag.

It also forbids us from driving an output marked as an interrupt
line.

This does not fit with the function name and expected semantics. In
the w1 host driver (for example) we need to handle a line as open drain
but sometimes force it to pull up, which means we should be able to
use the gpiod_set_raw_value() for this, but it currently does not
work.

There are also use cases where users actually want to drive a line
used by an interrupt. This is what they should be expected to use
the *raw* accessors for.

I have looked over the current users of this API and they do not seem
to be using the *raw* accessors with open drain or open source so let's
augment this behaviour before we have users expecting the inconsistent
semantic.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The arbitrarily marking of a function with _ or __ is taking to mean
"perform some inner core of the caller" or something like that. At other
times, this syntax has a totally different meaning.

I don't like this since it is unambious and unhelpful to people reading
the code, so replace it with _commit() suffixes.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This driver implements .alloc() hook, so .map() is not used.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

devm_kasprintf() can fail here and we must check its return value.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

devm_kasprintf() can fail here and we must check its return value.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch supports irq_set_wake for dwapb gpio. It allows GPIOs
to be configured as wakeup sources and wake the system from suspend.
Signed-off-by: NHoan Tran <hotran@apm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since f94277af ("of/platform: Initialise dev->fwnode appropriately"),
of_platform_device_create() already initialises dev->fwnode to that of
the appropriate device_node, so within the driver we shouldn't need to
care whether we probed via DT or ACPI.
Signed-off-by: NRobin Murphy <robin.murphy@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit 5620a0d1 ("firmware: delete in-kernel firmware") removed the
entire firmware directory.  Unfortunately it thereby also removed the
support for built-in firmware.

This restores the ability to build firmware directly into the kernel by
pruning the original Makefile to the necessary minimum.  The default for
EXTRA_FIRMWARE_DIR is now the standard directory /lib/firmware/.

Fixes: 5620a0d1 ("firmware: delete in-kernel firmware")
Signed-off-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: NGreg K-H <gregkh@linuxfoundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.

This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.

Fixes: 65e65ec1 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NAndreas Rammhold <andreas@rammhold.de>
Reported-by: NFlorian Klink <flokli@flokli.de>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default receive buffer size was reduced by recent change
to a value which was appropriate for 10G and Windows Server 2016.
But the value is too small for full performance with 40G on Azure.
Increase the default back to maximum supported by host.

Fixes: 8b532797 ("netvsc: allow controlling send/recv buffer size")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the network interface is kept running during suspend, the net core
may call net_device_ops.ndo_start_xmit() while the Ethernet device is
still suspended, which may lead to a system crash.

E.g. on sh73a0/kzm9g and r8a73a4/ape6evm, the external Ethernet chip is
driven by a PM controlled clock.  If the Ethernet registers are accessed
while the clock is not running, the system will crash with an imprecise
external abort.

As this is a race condition with a small time window, it is not so easy
to trigger at will.  Using pm_test may increase your chances:

    # echo 0 > /sys/module/printk/parameters/console_suspend
    # echo platform > /sys/power/pm_test
    # echo mem > /sys/power/state

To fix this, make sure the network interface is quietened during
suspend.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can enter a deadlock situation because there is no sufficient protection
when ndo_get_stats64() runs in process context to guard against RX or TX NAPI
contexts running in softirq, this can lead to the following lockdep splat and
actual deadlock was experienced as well with an iperf session in the background
and a while loop doing ifconfig + ethtool.

[    5.780350] ================================
[    5.784679] WARNING: inconsistent lock state
[    5.789011] 4.13.0-rc7-02179-g32fae27c725d #70 Not tainted
[    5.794561] --------------------------------
[    5.798890] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[    5.804971] swapper/0/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
[    5.810175]  (&syncp->seq#2){+.?...}, at: [<c0768a28>] bcm_sysport_tx_reclaim+0x30/0x54
[    5.818327] {SOFTIRQ-ON-W} state was registered at:
[    5.823278]   bcm_sysport_get_stats64+0x17c/0x258
[    5.828053]   dev_get_stats+0x38/0xac
[    5.831776]   rtnl_fill_stats+0x30/0x118
[    5.835761]   rtnl_fill_ifinfo+0x538/0xe24
[    5.839921]   rtmsg_ifinfo_build_skb+0x6c/0xd8
[    5.844430]   rtmsg_ifinfo_event.part.5+0x14/0x44
[    5.849201]   rtmsg_ifinfo+0x20/0x28
[    5.852837]   register_netdevice+0x628/0x6b8
[    5.857171]   register_netdev+0x14/0x24
[    5.861051]   bcm_sysport_probe+0x30c/0x438
[    5.865280]   platform_drv_probe+0x50/0xb0
[    5.869418]   driver_probe_device+0x2e8/0x450
[    5.873817]   __driver_attach+0x104/0x120
[    5.877871]   bus_for_each_dev+0x7c/0xc0
[    5.881834]   bus_add_driver+0x1b0/0x270
[    5.885797]   driver_register+0x78/0xf4
[    5.889675]   do_one_initcall+0x54/0x190
[    5.893646]   kernel_init_freeable+0x144/0x1d0
[    5.898135]   kernel_init+0x8/0x110
[    5.901665]   ret_from_fork+0x14/0x2c
[    5.905363] irq event stamp: 24263
[    5.908804] hardirqs last  enabled at (24262): [<c08eecf0>] net_rx_action+0xc4/0x4e4
[    5.916624] hardirqs last disabled at (24263): [<c0a7da00>] _raw_spin_lock_irqsave+0x1c/0x98
[    5.925143] softirqs last  enabled at (24258): [<c022a7fc>] irq_enter+0x84/0x98
[    5.932524] softirqs last disabled at (24259): [<c022a918>] irq_exit+0x108/0x16c
[    5.939985]
[    5.939985] other info that might help us debug this:
[    5.946576]  Possible unsafe locking scenario:
[    5.946576]
[    5.952556]        CPU0
[    5.955031]        ----
[    5.957506]   lock(&syncp->seq#2);
[    5.960955]   <Interrupt>
[    5.963604]     lock(&syncp->seq#2);
[    5.967227]
[    5.967227]  *** DEADLOCK ***
[    5.967227]
[    5.973222] 1 lock held by swapper/0/0:
[    5.977092]  #0:  (&(&ring->lock)->rlock){..-...}, at: [<c0768a18>] bcm_sysport_tx_reclaim+0x20/0x54

So just remove the u64_stats_update_begin()/end() pair in ndo_get_stats64()
since it does not appear to be useful for anything. No inconsistency was
observed with either ifconfig or ethtool, global TX counts equal the sum of
per-queue TX counts on a 32-bit architecture.

Fixes: 10377ba7 ("net: systemport: Support 64bit statistics")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When building an allmodconfig kernel with gcc-4.6, we get a rather
odd warning:

drivers/net/vrf.c: In function ‘vrf_ip6_input_dst’:
drivers/net/vrf.c:964:3: error: initialized field with side-effects overwritten [-Werror]
drivers/net/vrf.c:964:3: error: (near initialization for ‘fl6’) [-Werror]

I have no idea what this warning is even trying to say, but it does
seem like a false positive. Reordering the initialization in to match
the structure definition gets rid of the warning, and might also avoid
whatever gcc thinks is wrong here.

Fixes: 9ff74384 ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.

Semantic patch used to resolve this issue:

@@
expression e,e2; constant c;
statement S;
@@

  e = kzalloc(e2, c);
  if(e == NULL) S
- memset(e, 0, e2);
Signed-off-by: NHimanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: NHimanshu Jha <himanshujha199640@gmail.com>
Acked-by: NSudarsana Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to other Gigabyte laptops, the touchpad on P57 requires a
keyboard reset to detect Elantech touchpad correctly.

BugLink: https://bugs.launchpad.net/bugs/1594214Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This reverts commit 40f11adc.

Jens found that iwlwifi firmware loading failed on a Lenovo X1 Carbon,
gen4:

  iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-8000C-34.ucode failed with error -2
  iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-8000C-33.ucode failed with error -2
  iwlwifi 0000:04:00.0: Direct firmware load for iwlwifi-8000C-32.ucode failed with error -2
  iwlwifi 0000:04:00.0: loaded firmware version 31.532993.0 op_mode iwlmvm
  iwlwifi 0000:04:00.0: Detected Intel(R) Dual Band Wireless AC 8260, REV=0x208
  ...
  iwlwifi 0000:04:00.0: Failed to load firmware chunk!
  iwlwifi 0000:04:00.0: Could not load the [0] uCode section
  iwlwifi 0000:04:00.0: Failed to start INIT ucode: -110
  iwlwifi 0000:04:00.0: Failed to run INIT ucode: -110

He bisected it to 40f11adc ("PCI: Avoid race while enabling upstream
bridges").  Revert that commit to fix the regression.

Link: http://lkml.kernel.org/r/4bcbcbc1-7c79-09f0-5071-bc2f53bf6574@kernel.dk
Fixes: 40f11adc ("PCI: Avoid race while enabling upstream bridges")
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
CC: Srinath Mannam <srinath.mannam@broadcom.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Luca Coelho <luca@coelho.fi>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

tnapi is being initialized and then immediately updated and
hence the initialiation is redundant.  Clean up the warning
by moving the declaration and initialization to the inside
of the for-loop.

Cleans up clang scan-build warning:
warning: Value stored to 'tnapi' during its initialization is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds initial support for the STM32F7 I2C controller.
Signed-off-by: NM'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: NPierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch uses a more generic definition of speed enum for i2c-stm32f4
driver.
Signed-off-by: NM'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: NPierre-Yves MORDRET <pierre-yves.mordret@st.com>
Reviewed-by: NLudovic BARRE <ludovic.barre@st.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

... and __initconst if applicable.

Based on similar work for an older kernel in the Grsecurity patch.

[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJean Delvare <jdelvare@suse.de>

GFP_TEMPORARY was introduced by commit e12ba74d ("Group short-lived
and reclaimable kernel allocations") along with __GFP_RECLAIMABLE.  It's
primary motivation was to allow users to tell that an allocation is
short lived and so the allocator can try to place such allocations close
together and prevent long term fragmentation.  As much as this sounds
like a reasonable semantic it becomes much less clear when to use the
highlevel GFP_TEMPORARY allocation flag.  How long is temporary? Can the
context holding that memory sleep? Can it take locks? It seems there is
no good answer for those questions.

The current implementation of GFP_TEMPORARY is basically GFP_KERNEL |
__GFP_RECLAIMABLE which in itself is tricky because basically none of
the existing caller provide a way to reclaim the allocated memory.  So
this is rather misleading and hard to evaluate for any benefits.

I have checked some random users and none of them has added the flag
with a specific justification.  I suspect most of them just copied from
other existing users and others just thought it might be a good idea to
use without any measuring.  This suggests that GFP_TEMPORARY just
motivates for cargo cult usage without any reasoning.

I believe that our gfp flags are quite complex already and especially
those with highlevel semantic should be clearly defined to prevent from
confusion and abuse.  Therefore I propose dropping GFP_TEMPORARY and
replace all existing users to simply use GFP_KERNEL.  Please note that
SLAB users with shrinkers will still get __GFP_RECLAIMABLE heuristic and
so they will be placed properly for memory fragmentation prevention.

I can see reasons we might want some gfp flag to reflect shorterm
allocations but I propose starting from a clear semantic definition and
only then add users with proper justification.

This was been brought up before LSF this year by Matthew [1] and it
turned out that GFP_TEMPORARY really doesn't have a clear semantic.  It
seems to be a heuristic without any measured advantage for most (if not
all) its current users.  The follow up discussion has revealed that
opinions on what might be temporary allocation differ a lot between
developers.  So rather than trying to tweak existing users into a
semantic which they haven't expected I propose to simply remove the flag
and start from scratch if we really need a semantic for short term
allocations.

[1] http://lkml.kernel.org/r/20170118054945.GD18349@bombadil.infradead.org

[akpm@linux-foundation.org: fix typo]
[akpm@linux-foundation.org: coding-style fixes]
[sfr@canb.auug.org.au: drm/i915: fix up]
  Link: http://lkml.kernel.org/r/20170816144703.378d4f4d@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170728091904.14627-1-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NMel Gorman <mgorman@suse.de>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

gcc-7 points out that a negative port_num value would overflow the
string buffer:

  drivers/infiniband/hw/mlx4/sysfs.c: In function 'mlx4_ib_device_register_sysfs':
  drivers/infiniband/hw/mlx4/sysfs.c:251:16: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
  drivers/infiniband/hw/mlx4/sysfs.c:251:2: note: 'sprintf' output between 2 and 11 bytes into a destination of size 10
  drivers/infiniband/hw/mlx4/sysfs.c:303:17: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
  drivers/infiniband/hw/mlx4/sysfs.c:303:3: note: 'sprintf' output between 2 and 11 bytes into a destination of size 10

While we should be able to assume that port_num is positive here, making
the buffer one byte longer has no downsides and avoids the warning.

Fixes: c1e7e466 ("IB/mlx4: Add iov directory in sysfs under the ib device")
Link: http://lkml.kernel.org/r/20170714120720.906842-23-arnd@arndb.deSigned-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

gcc-4.4.4 has issues with initialization of anonymous unions:

  drivers/media/cec/cec-adap.c: In function 'cec_queue_msg_fh':
  drivers/media/cec/cec-adap.c:184: error: unknown field 'lost_msgs' specified in initializer

work around this.

Fixes: 6b2bbb08 ("media: cec: rework the cec event handling")
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add driver support for the Altera I2C Controller. The I2C
controller is soft IP for use in FPGAs.
Signed-off-by: NThor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The control process (NSP) may take some time to complete its
initialization.  This is not a problem on most servers, but
on very fast-booting machines it may not be ready for operation
when driver probes the device.  There is also a version of the
flash in the wild where NSP tries to train the links as part
of init.  To wait for NSP initialization we should make sure
its resource has already been added to the resource table.
NSP adds itself there as last step of init.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Board state informs us which low-level initialization stages the card
has completed.  We should wait for the card to be fully initialized
before trying to communicate with it, not only before we configure
passing traffic.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not check the flow dissector against a list of allowed
and supported flow key dissectors. This patch introduces such a list and
correctly rejects unsupported flow keys.

Fixes: 43f84b72 ("nfp: add metadata to each flow offload")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NRichard Weinberger <richard@nod.at>

Trivial fix to spelling mistake in ubi_err error message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NRichard Weinberger <richard@nod.at>

In build.c, the following pr_err calls should be terminated with
a new-line to avoid other messages being concatenated onto the end.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NRichard Weinberger <richard@nod.at>

In ubi_attach_mtd_dev() the pr_err() calls should have their
messgaes terminated with a new-line to avoid other messages
being concatenated onto the end.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NRichard Weinberger <richard@nod.at>