Make AIFCLK supply the record paths otherwise record will not work unless
there is a simultaneous playback.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

asoc cache layer can't support this kind of spi registers well.
remove cache support and read/write registers directly
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

dac word len value should left shift before setting
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Acked-by: NBarry Song <21cnbao@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

fix dac word len mask and adc tdm fmt shift value
Signed-off-by: NScott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When the clocking registers are not overriden some of the registers are
not writable.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Cc: stable@kernel.org

sound/soc/codecs/wm8750.c:784:2: warning: missing braces around initializer
sound/soc/codecs/wm8750.c:784:2: warning: (near initialization for ‘wm8750_spi_ids[2].name’)

It's because struct spi_device_id.name is a char array, not a pointer,
while the driver initializes explicitly with 0.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>

This error would have no effect on current silicon revisions, the fall
through case has the same behaviour.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>

As we had no id_table only the driver name would be matched against
meaning that WM8987 devices wouldn't be bound.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Without this, request_irq on subsequent device initialization fails, and
the codec cannot be used.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This closes the small race between a status being read in response to an
interrupt and clearing the interrupt, meaning that if the status changes
between those periods we might not get a reassertion of the interrupt.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Cache handling in this driver is broken. The chip has 16-bit registers, yet the
register numbers also increase by 2 per register, i.e.  there are only
even-numbered registers. The cache in this driver, though, simply increments
register numbers, so it does need some mapping as seen in
sgtl5000_restore_regs(), note the '>> 1':

	snd_soc_write(codec, SGTL5000_CHIP_LINREG_CTRL,
                        cache[SGTL5000_CHIP_LINREG_CTRL >> 1]);

That, of course, won't work with snd_soc_update_bits(). (Thus, we won't even
notice the missing register 0x1c in the default regs which shifted all follwing
registers to wrong values.) Noticed on the MX28EVK where enabling the regulators
simply locked up the chip.

Refactor the routines and use a properly sized default_regs array which matches
the register layout of the underlying chip, i.e. create a truly flat cache.
This also saves some code which should make up for the bigger array a little.
When soc-core will somewhen have another cache type which handles a step size,
this conversion will also ease the transition.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NDong Aisheng <b29396@freescale.com>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

This does not function correctly in all circumstances so disable the
periodic updates unconditionally for stable; a future patch will reenable
where appropriate.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

This closes the small race between a status being read in response to an
interrupt and clearing the interrupt, meaning that if the status changes
between those periods we might not get a reassertion of the interrupt.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Print a hint when the user has a setup where CONFIG_REGULATOR is really
needed to make the driver work.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NDong Aisheng <b29396@freescale.com>
Tested-by: NShawn Guo <shawn.guo@freescale.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The code for registering the internal ldo was present twice. Turn it
into a function instead. Also, inform the user if LDO is used now.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NDong Aisheng <b29396@freescale.com>
Tested-by: NShawn Guo <shawn.guo@freescale.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8994 and WM8958 series of devices have two MICBIAS supplies rather
than one, the current widget actually manages the microphone detection
control register bit (which is managed separately by the relevant API).

Fix this, hooking the relevant supplies up to the MICBIAS1 and MICBIAS2
widgets.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

If DAIs are idle but their clocks are in use for some reason (eg, as
SYSCLK or for accessory detect) then set the clock dividers to the maximum
to reduce slightly the power consumption of the unclocked circuits.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Not only fixes error handling but also some uninitialized variable
warnings.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>

Try the completion before we start the FLL so that if an interrupt was
delayed long enough for us to miss it we don't wait for the completion
it signalled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Don't assume the first fire indicates that we're done.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The WM8983 is a low power, high quality stereo CODEC
designed for portable multimedia applications. Highly flexible
analogue mixing functions enable new application features,
combining hi-fi quality audio with voice communication.
Signed-off-by: NDimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We should spot them anyway on state changes but logging them gives us
better time information about when the misconfiguration happened.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We can have valid but very low clocks in accessory detection modes.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If we have interrupts then wait for the FLL lock interrupt rather than
using dead reckoning when waiting for the FLL to start.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The individual devices should set the flag dcs_done_irq in the hubs
shared data structure to indicate that they will flag the interrupt
by calling wm_hubs_dcs_done().
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This ensures appropriate clocking for bypass paths to speaker and
headphone and direct voice paths on affected revisions.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Chip documentation explicitly requires that the reset values
of reserved register bits are left untouched.  It is possible
there are differences between STA326 and STA328 or future
chip revisions in these bits, and clobbering them might
cause malfunction.
Signed-off-by: NJohannes Stezenbach <js@sig21.net>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The STA32x has a number of preset EQ settings, but also
allows full user control of the biquad filter coeffcients
(when "Automode EQ" is set to "User").
Each biquad has five signed, 24bit, fixed-point coefficients
representing the range -1...1.  The five biquad coefficients
can be uploaded in one atomic operation into on-chip
coefficient RAM.
There are also a few prescale, postscale and mixing
coefficients, in the same numeric format and range
(a negative coefficient inverts phase).

These coefficients are made available as SNDRV_CTL_ELEM_TYPE_BYTES
mixer controls.
Signed-off-by: NJohannes Stezenbach <js@sig21.net>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Future devices will not benefit from this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

mask didn't cover update-data
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The legacy mode has been accidentaly removed by commit:
ASoC: twl6040: add all ABE DAIs

Add back the twl6040-hifi dai.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since the PLL handling has been simplified, and
rebased on 0, there is no longer need for converting
the PLL ID.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Avoid configuring the PLL several times during audio startup.
We can configure the PLL at prepare time with parameters collected
earlier hw_param, and set_dai_sysclk calls.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>