USB 3.0 hubs don't have a port suspend change bit (that bit is now
reserved).  Instead, when a host-initiated resume finishes, the hub sets
the port link state change bit.

When a USB 3.0 device initiates remote wakeup, the parent hubs with
their upstream links in U3 will pass the LFPS up the chain.  The first
hub that has an upstream link in U0 (which may be the roothub) will
reflect that LFPS back down the path to the device.

However, the parent hubs in the resumed path will not set their link
state change bit.  Instead, the device that initiated the resume has to
send an asynchronous "Function Wake" Device Notification up to the host
controller.  Therefore, we need a way to notify the USB core of a device
resume without going through the normal hub URB completion method.

First, make the xHCI roothub act like an external USB 3.0 hub and not
pass up the port link state change bit when a device-initiated resume
finishes.  Introduce a new xHCI bit field, port_remote_wakeup, so that
we can tell the difference between a port coming out of the U3Exit state
(host-initiated resume) and the RExit state (ending state of
device-initiated resume).

Since the USB core can't tell whether a port on a hub has resumed by
looking at the Hub Status buffer, we need to introduce a bitfield,
wakeup_bits, that indicates which ports have resumed.  When the xHCI
driver notices a port finishing a device-initiated resume, we call into
a new USB core function, usb_wakeup_notification(), that will set
the right bit in wakeup_bits, and kick khubd for that hub.

We also call usb_wakeup_notification() when the Function Wake Device
Notification is received by the xHCI driver.  This covers the case where
the link between the roothub and the first-tier hub is in U0, and the
hub reflects the resume signaling back to the device without giving any
indication it has done so until the device sends the Function Wake
notification.

Change the code in khubd that handles the remote wakeup to look at the
state the USB core thinks the device is in, and handle the remote wakeup
if the port's wakeup bit is set.

This patch only takes care of the case where the device is attached
directly to the roothub, or the USB 3.0 hub that is attached to the root
hub is the device sending the Function Wake Device Notification (e.g.
because a new USB device was attached).  The other cases will be covered
in a second patch.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

USB 3.0 hubs have a different remote wakeup policy than USB 2.0 hubs.
USB 2.0 hubs, once they have remote wakeup enabled, will always send
remote wakes when anything changes on a port.

However, USB 3.0 hubs have a per-port remote wake up policy that is off
by default.  The Set Feature remote wake mask can be changed for any
port, enabling remote wakeup for a connect, disconnect, or overcurrent
event, much like EHCI and xHCI host controller "wake on" port status
bits.  The bits are cleared to zero on the initial hub power on, or
after the hub has been reset.

Without this patch, when a USB 3.0 hub gets suspended, it will not send
a remote wakeup on device connect or disconnect.  This would show up to
the user as "dead ports" unless they ran lsusb -v (since newer versions
of lsusb use the sysfs files, rather than sending control transfers).

Change the hub driver's suspend method to enable remote wake up for
disconnect, connect, and overcurrent for all ports on the hub.  Modify
the xHCI driver's roothub code to handle that request, and set the "wake
on" bits in the port status registers accordingly.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Somehow we ended up with duplicate hub feature #defines in ch11.h.
Tatyana Brokhman first created the USB 3.0 hub feature macros in 2.6.38
with commit 0eadcc09 "usb: USB3.0 ch11
definitions".  In 2.6.39, I modified a patch from John Youn that added
similar macros in a different place in the same file, and committed
dbe79bbe "USB 3.0 Hub Changes".

Some of the #defines used different names for the same values.  Others
used exactly the same names with the same values, like these gems:

 #define USB_PORT_FEAT_BH_PORT_RESET     28
...
 #define USB_PORT_FEAT_BH_PORT_RESET            28

According to my very geeky husband (who looked it up in the C99 spec),
it is allowed to have object-like macros with duplicate names as long as
the replacement list is exactly the same.  However, he recalled that
some compilers will give warnings when they find duplicate macros.  It's
probably best to remove the duplicates in the stable tree, so that the
code compiles for everyone.

The macros are now fixed to move the feature requests that are specific
to USB 3.0 hubs into a new section (out of the USB 2.0 hub feature
section), and use the most common macro name.

This patch should be backported to 2.6.39.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Jamey Sharp <jamey@minilop.net>
Cc: stable@vger.kernel.org

Add macro which prints an error message only once if port is used a
console.

Reporting errors in a write path when port is used as a console could
otherwise result in an infinite loop.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Userspace may want to make policy decisions based on whether or not a
given USB device is removable. Add a per-device member and support
for exposing it in sysfs. Information sources to populate it will be
added later.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Setting the task name is done within setup_new_exec() by accessing
bprm->filename. However this happens after flush_old_exec().
This may result in a use after free bug, flush_old_exec() may
"complete" vfork_done, which will wake up the parent which in turn
may free the passed in filename.
To fix this add a new tcomm field in struct linux_binprm which
contains the now early generated task name until it is used.

Fixes this bug on s390:

  Unable to handle kernel pointer dereference at virtual kernel address 0000000039768000
  Process kworker/u:3 (pid: 245, task: 000000003a3dc840, ksp: 0000000039453818)
  Krnl PSW : 0704000180000000 0000000000282e94 (setup_new_exec+0xa0/0x374)
  Call Trace:
  ([<0000000000282e2c>] setup_new_exec+0x38/0x374)
   [<00000000002dd12e>] load_elf_binary+0x402/0x1bf4
   [<0000000000280a42>] search_binary_handler+0x38e/0x5bc
   [<0000000000282b6c>] do_execve_common+0x410/0x514
   [<0000000000282cb6>] do_execve+0x46/0x58
   [<00000000005bce58>] kernel_execve+0x28/0x70
   [<000000000014ba2e>] ____call_usermodehelper+0x102/0x140
   [<00000000005bc8da>] kernel_thread_starter+0x6/0xc
   [<00000000005bc8d4>] kernel_thread_starter+0x0/0xc
  Last Breaking-Event-Address:
   [<00000000002830f0>] setup_new_exec+0x2fc/0x374

  Kernel panic - not syncing: Fatal exception: panic_on_oops
Reported-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Looks like change "PM QoS: Move and rename the implementation files"
merged during the 3.2 development cycle made PM QoS depend on
CONFIG_PM which depends on (PM_SLEEP || PM_RUNTIME).

That breaks CPU C-states with kernels not having these CONFIGs, causing CPUs
to spend time in Polling loop idle instead of going into deep C-states,
consuming way way more power. This is with either acpi idle or intel idle
enabled.

Either CONFIG_PM should be enabled with any pm_qos users or
the !CONFIG_PM pm_qos_request() should return sane defaults not to break
the existing users. Here's is the patch for the latter option.

[rjw: Modified the changelog slightly.]
Signed-off-by: NVenkatesh Pallipadi <venki@google.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Cc: stable@vger.kernel.org

Store the last used mclk configuration for the PLL.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The usb/ch9.h will be installed to /usr/include/linux,
and be used from user space.
But le16_to_cpu() is only defined for kernel code.
Without this patch, user space compile will be broken.
Special thanks to Stefan Becker

Cc: stable@vger.kernel.org # 3.2
Reported-by: NStefan Becker <chemobejk@gmail.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

usb_pipe_usage_descriptor defines the struct which is used to describe
the type of the endpoint in UAS (status/command/data in+out). It will be
used by the UAS gadget, the host code is using a char array for the
access.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The protocol specific structures and defines which are used by UAS are
moved into a header files by this patch so it can be accessed by the UAS
gadget as well.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This fixes the race in process_vm_core found by Oleg (see

  http://article.gmane.org/gmane.linux.kernel/1235667/

for details).

This has been updated since I last sent it as the creation of the new
mm_access() function did almost exactly the same thing as parts of the
previous version of this patch did.

In order to use mm_access() even when /proc isn't enabled, we move it to
kernel/fork.c where other related process mm access functions already
are.
Signed-off-by: NChris Yeoh <yeohc@au1.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The usb/ch9.h will be installed to /usr/include/linux,
and be used from user space.
But le16_to_cpu() is only defined for kernel code.
Without this patch, user space compile will be broken.
Special thanks to Stefan Becker
Reported-by: NStefan Becker <chemobejk@gmail.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes merge conflict resolution breakage introduced by merge
d3712b9d ("Merge tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream").

The commit changed 'mtd_can_have_bb()' function and made it always
return zero, which is incorrect.  Instead, we need it to return whether
the underlying flash device can have bad eraseblocks or not.  UBI needs
this information because it affects how it handles the underlying flash.
E.g., if the underlying flash is NOR, it cannot have bad blocks and any
write or erase error is fatal, and all we can do is to switch to R/O
mode.  We do not need to reserve a pool of good eraseblocks for bad
eraseblocks handling, and so on.

This patch also removes 'mtd_can_have_bb()' invocations from Logfs to
ensure correct Logfs behavior.

I've tested that with this patch UBI works on top of NOR and NAND
flashes emulated by mtdram and nandsim correspondingly.

This patch is based on patch from Linus Torvalds.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: NJörn Engel <joern@logfs.org>
Acked-by: NPrasad Joshi <prasadjoshi.linux@gmail.com>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A struct device parameter is used in the enable and disable callbacks to
distinguish between different gpio_keys devices.

Platforms that don't use these callbacks may not include struct device
at all, as seen on arch/arm/mach-s3c2410/mach-n30.c
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add a flag to allow platforms to specify, whether a DMAC instance supports
the MEMCPY operation. To avoid regressions, preserve the current default.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

MPI_NULL is replaced with normal NULL.
Signed-off-by: NDmitry Kasatkin <dmitry.kasatkin@intel.com>
Reviewed-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NJames Morris <jmorris@namei.org>

Commits 3fe4bae8 and
079c985e broke MTD suspend in 2 ways:

1. When the '->suspend' method is not present, we return -EOPNOTSUPP, but
   the callers of 'mtd_suspend()' expects 0 instead.
2. Checking of the 'mtd' parameter against NULL has been incorrectly removed
   in 'mtd_cls_suspend()'.

This patch fixes the breakages. This has been found, analyzed, reported
and tested by Rafael J. Wysocki <rjw@sisk.pl>.

Note, this patch is not needed in the stable tree because it causes a
regression introduced during the v3.3 merge window.
Reported-by: NRafael J. Wysocki <rjw@sisk.pl>
Tested-by: NRafael J. Wysocki <rjw@sisk.pl>
Tested-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Commit 2aede851

  PM / Hibernate: Freeze kernel threads after preallocating memory

introduced a mechanism by which kernel threads were frozen after
the preallocation of hibernate image memory to avoid problems with
frozen kernel threads not responding to memory freeing requests.
However, it overlooked the s2disk code path in which the
SNAPSHOT_CREATE_IMAGE ioctl was run directly after SNAPSHOT_FREE,
which caused freeze_workqueues_begin() to BUG(), because it saw
that worqueues had been already frozen.

Although in principle this issue might be addressed by removing
the relevant BUG_ON() from freeze_workqueues_begin(), that would
reintroduce the very problem that commit 2aede851
attempted to avoid into that particular code path.  For this reason,
to fix the issue at hand, introduce thaw_kernel_threads() and make
the SNAPSHOT_FREE ioctl execute it.

Special thanks to Srivatsa S. Bhat for detailed analysis of the
problem.
Reported-and-tested-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: stable@kernel.org

This patch fixes the sampling interrupt throttling mechanism.

It was broken in v3.2. Events were not being unthrottled. The
unthrottling mechanism required that events be checked at each
timer tick.

This patch solves this problem and also separates:

  - unthrottling
  - multiplexing
  - frequency-mode period adjustments

Not all of them need to be executed at each timer tick.

This third version of the patch is based on my original patch +
PeterZ proposal (https://lkml.org/lkml/2012/1/7/87).

At each timer tick, for each context:

  - if the current CPU has throttled events, we unthrottle events

  - if context has frequency-based events, we adjust sampling periods

  - if we have reached the jiffies interval, we multiplex (rotate)

We decoupled rotation (multiplexing) from frequency-mode sampling
period adjustments.  They should not necessarily happen at the same
rate. Multiplexing is subject to jiffies_interval (currently at 1
but could be higher once the tunable is exposed via sysfs).

We have grouped frequency-mode adjustment and unthrottling into the
same routine to minimize code duplication. When throttled while in
frequency mode, we scan the events only once.

We have fixed the threshold enforcement code in __perf_event_overflow().
There was a bug whereby it would allow more than the authorized rate
because an increment of hwc->interrupts was not executed at the right
place.

The patch was tested with low sampling limit (2000) and fixed periods,
frequency mode, overcommitted PMU.

On a 2.1GHz AMD CPU:

 $ cat /proc/sys/kernel/perf_event_max_sample_rate
 2000

We set a rate of 3000 samples/sec (2.1GHz/3000 = 700000):

 $ perf record -e cycles,cycles -c 700000  noploop 10
 $ perf report -D | tail -21

 Aggregated stats:
           TOTAL events:      80086
            MMAP events:         88
            COMM events:          2
            EXIT events:          4
        THROTTLE events:      19996
      UNTHROTTLE events:      19996
          SAMPLE events:      40000

 cycles stats:
           TOTAL events:      40006
            MMAP events:          5
            COMM events:          1
            EXIT events:          4
        THROTTLE events:       9998
      UNTHROTTLE events:       9998
          SAMPLE events:      20000

 cycles stats:
           TOTAL events:      39996
        THROTTLE events:       9998
      UNTHROTTLE events:       9998
          SAMPLE events:      20000

For 10s, the cap is 2x2000x10 = 40000 samples.
We get exactly that: 20000 samples/event.
Signed-off-by: NStephane Eranian <eranian@google.com>
Cc: <stable@kernel.org> # v3.2+
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120126160319.GA5655@quadSigned-off-by: NIngo Molnar <mingo@elte.hu>

This patch changes event message behaviour to send only updated records
instead of whole list. This fixes bug on which userspace receives non-actual
data in case multiple events occur in row.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix new kernel-doc warning:

Warning(include/linux/usb.h:1251): No description found for parameter 'num_mapped_sgs'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix new kernel-doc warnings:

Warning(include/linux/device.h:299): No description found for parameter 'name'
Warning(include/linux/device.h:299): No description found for parameter 'subsys'
Warning(include/linux/device.h:299): No description found for parameter 'node'
Warning(include/linux/device.h:299): No description found for parameter 'add_dev'
Warning(include/linux/device.h:299): No description found for parameter 'remove_dev'
Warning(include/linux/device.h:685): No description found for parameter 'id'
Warning(include/linux/device.h:1009): No description found for parameter '__driver'
Warning(include/linux/device.h:1009): No description found for parameter '__register'
Warning(include/linux/device.h:1009): No description found for parameter '__unregister'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The way this driver was added by f0ae849d (usb: Add Intel Langwell USB
OTG Transceiver Driver) never even compiled together with langwell_udc,
and that's the only way for it to be useful.
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: stable@vger.kernel.org # v2.6.31+
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NFelipe Balbi <balbi@ti.com>

so move its include into fs.h inside the __KERNEL__ protection.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix new kernel-doc notation warnings:

Warning(include/linux/sched.h:2094): No description found for parameter 'p'
Warning(include/linux/sched.h:2094): Excess function parameter 'tsk' description in 'is_idle_task'
Warning(kernel/sched/cpupri.c:139): No description found for parameter 'newpri'
Warning(kernel/sched/cpupri.c:139): Excess function parameter 'pri' description in 'cpupri_set'
Warning(kernel/sched/cpupri.c:208): Excess function parameter 'bootmem' description in 'cpupri_init'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc:	Ingo Molnar <mingo@elte.hu>
Cc:	Peter Zijlstra <peterz@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix new kernel-doc warning:

Warning(include/linux/usb.h:1251): No description found for parameter 'num_mapped_sgs'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix new kernel-doc warnings:

Warning(include/linux/device.h:299): No description found for parameter 'name'
Warning(include/linux/device.h:299): No description found for parameter 'subsys'
Warning(include/linux/device.h:299): No description found for parameter 'node'
Warning(include/linux/device.h:299): No description found for parameter 'add_dev'
Warning(include/linux/device.h:299): No description found for parameter 'remove_dev'
Warning(include/linux/device.h:685): No description found for parameter 'id'
Warning(include/linux/device.h:1009): No description found for parameter '__driver'
Warning(include/linux/device.h:1009): No description found for parameter '__register'
Warning(include/linux/device.h:1009): No description found for parameter '__unregister'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit cc39c6a9 ("mm: account skipped entries to avoid looping in
find_get_pages") correctly fixed an infinite loop; but left a problem
that find_get_pages() on shmem would return 0 (appearing to callers to
mean end of tree) when it meets a run of nr_pages swap entries.

The only uses of find_get_pages() on shmem are via pagevec_lookup(),
called from invalidate_mapping_pages(), and from shmctl SHM_UNLOCK's
scan_mapping_unevictable_pages().  The first is already commented, and
not worth worrying about; but the second can leave pages on the
Unevictable list after an unusual sequence of swapping and locking.

Fix that by using shmem_find_get_pages_and_swap() (then ignoring the
swap) instead of pagevec_lookup().

But I don't want to contaminate vmscan.c with shmem internals, nor
shmem.c with LRU locking.  So move scan_mapping_unevictable_pages() into
shmem.c, renaming it shmem_unlock_mapping(); and rename
check_move_unevictable_page() to check_move_unevictable_pages(), looping
down an array of pages, oftentimes under the same lock.

Leave out the "rotate unevictable list" block: that's a leftover from
when this was used for /proc/sys/vm/scan_unevictable_pages, whose flawed
handling involved looking at pages at tail of LRU.

Was there significance to the sequence first ClearPageUnevictable, then
test page_evictable, then SetPageUnevictable here? I think not, we're
under LRU lock, and have no barriers between those.
Signed-off-by: NHugh Dickins <hughd@google.com>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: <stable@vger.kernel.org> [back to 3.1 but will need respins]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kdump only allocates memory for the prstatus ELF note.  For s390x,
besides of prstatus multiple ELF notes for various different register
types are stored.  Therefore the currently allocated memory is not
sufficient.  With this patch the KEXEC_NOTE_BYTES macro can be defined
by architecture code and for s390x it is set to the correct size now.
Signed-off-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sparc64 allmodconfig:

In file included from include/linux/compat.h:15,
                 from /usr/src/25/arch/sparc/include/asm/siginfo.h:19,
                 from include/linux/signal.h:5,
                 from include/linux/sched.h:73,
                 from arch/sparc/kernel/asm-offsets.c:13:
include/linux/fs.h:618: warning: parameter has incomplete type

It seems that my sparc64 compiler (gcc-3.4.5) doesn't like the forward
declaration of enums.

Fix this by moving the "enum migrate_mode" definition into its own header
file.
Acked-by: NMel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andy Isaacson <adi@hexapodia.org>
Cc: Nai Xia <nai.xia@gmail.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It doesn't seem right for the thermal subsystem to export a symbol
named generate_netlink_event. This function is thermal-specific and
its name should reflect that fact. Rename it to
thermal_generate_netlink_event.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NR.Durgadoss <durgadoss.r@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Now that all users of 'struct sysdev' are removed from the kernel, we
can safely remove the .h and .c files for this code, to ensure that no
one accidentally starts to use it again.

Many thanks for Kay who did all the hard work here on making this
happen.

Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is a case in __sk_mem_schedule(), where an allocation
is beyond the maximum, but yet we are allowed to proceed.
It happens under the following condition:

	sk->sk_wmem_queued + size >= sk->sk_sndbuf

The network code won't revert the allocation in this case,
meaning that at some point later it'll try to do it. Since
this is never communicated to the underlying res_counter
code, there is an inbalance in res_counter uncharge operation.

I see two ways of fixing this:

1) storing the information about those allocations somewhere
   in memcg, and then deducting from that first, before
   we start draining the res_counter,
2) providing a slightly different allocation function for
   the res_counter, that matches the original behavior of
   the network code more closely.

I decided to go for #2 here, believing it to be more elegant,
since #1 would require us to do basically that, but in a more
obscure way.
Signed-off-by: NGlauber Costa <glommer@parallels.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
CC: Tejun Heo <tj@kernel.org>
CC: Li Zefan <lizf@cn.fujitsu.com>
CC: Laurent Chavey <chavey@google.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the memcg sock code, we'll need to register allocations
that are temporarily over limit. Let's make sure that margin
is 0 in this case.

I am keeping this as a separate patch, so that if any weirdness
interaction appears in the future, we can now exactly what caused
it.

Suggested by Johannes Weiner
Signed-off-by: NGlauber Costa <glommer@parallels.com>
CC: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
CC: Johannes Weiner <hannes@cmpxchg.org>
CC: Michal Hocko <mhocko@suse.cz>
CC: Tejun Heo <tj@kernel.org>
CC: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correctly implement a loss detection heuristic: New sequences (above
high_seq) sent during the fast recovery are deemed lost when higher
sequences are SACKed.

Current code does not catch these losses, because tcp_mark_head_lost()
does not check packets beyond high_seq. The fix is straight-forward by
checking packets until the highest sacked packet. In addition, all the
FLAG_DATA_LOST logic are in-effective and redundant and can be removed.

Update the loss heuristic comments. The algorithm above is documented
as heuristic B, but it is redundant too because heuristic A already
covers B.

Note that this change only marks some forward-retransmitted packets LOST.
It does NOT forbid TCP performing further CWR on new losses. A potential
follow-up patch under preparation is to perform another CWR on "new"
losses such as
1) sequence above high_seq is lost (by resetting high_seq to snd_nxt)
2) retransmission is lost.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In native mode display all available staticstics.
In SRIOV mode on VF display only SW counters statistics,
in SRIOV mode on hypervisor display SW counters and errors (got from FW)
statistics.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mcp_priv() does unexpected things when passed a void pointer.  Make it
a typed inline function, which ensures that it works correctly in
these cases.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This reverts commit 5dd7bf59.

Conflicts:

	scripts/mod/file2alias.c

This change is wrong on many levels.  First and foremost, it causes a
regression.  On boot on Assabet, which this patch gives a codec id of
'ucb1x00', it gives:

	ucb1x00 ID not found: 1005

0x1005 is a valid ID for the UCB1300 device.

Secondly, this patch is way over the top in terms of complexity.  The
only device which has been seen to be connected with this MCP code is
the UCB1x00 (UCB1200, UCB1300 etc) devices, and they all use the same
driver.  Adding a match table, requiring the codec string to match the
hardware ID read out of the ID register, etc is completely over the top
when we can just read the hardware ID register.