Instead of defining an enumeration with the FW specific values for the
different clock rates, use the actual frequency instead.  Also add a
boolean to specify whether the clock is XTAL or not.

Change all board files to reflect this.
Signed-off-by: NLuciano Coelho <luca@coelho.fi>
[Eliad - small fixes, update board file changes]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
Acked-by: NKalle Valo <kvalo@codeaurora.org>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The platform_quirk element in the platform data was used
to change the way the IRQ is triggered.  When set,
the EDGE_IRQ quirk would change the irqflags used
and treat edge trigger differently from the rest.

Instead of hiding this irq flag setting behind the quirk,
have the board files set the irq_trigger explicitly.

This will allow us to use standard irq DT definitions
later on.
Signed-off-by: NLuciano Coelho <luca@coelho.fi>
[Eliad - rebase, add irq_trigger field and pass it,
update board file changes]
Signed-off-by: NEliad Peller <eliad@wizery.com>
Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
Acked-by: NKalle Valo <kvalo@codeaurora.org>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I upgraded my u-boot and noticed that wl12xx stopped working.
Turns out the kernel is not setting the quirk for the MMC2
copy clock while the eariler bootloader I had was setting it.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This is no longer needed now that 3517 is booting in device tree
only mode.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove ADS7846 touchscreen pdata quirk for CM-T3x CoMs
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add btwilink device for IGEPv2 Rev. F and IGEP COM MODULE Rev. G.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.

Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.

And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the more common pr_warn.

Other miscellanea:

o Realign arguments
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As we have support for this in board-rx51-peripherals.c, let's
add it to the .dts files too.

Note that the reset GPIO will eventually go to the driver.
For now let's just pull it down and skip any further reset
in case the bootloader has configured the MAC address so
NFSroot works.

Also note that after 3430-sdp are using proper GPMC timings
we can remove the tests for smsc,lan91c94 in gpmc.c.
Signed-off-by: NTony Lindgren <tony@atomide.com>

By moving i2c devices to DT we can clean up
i2c_board_info and fix a problem with moving
INTC to irq domain where IRQs can be renumbered
on each boot.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. So mark the
non-const function parameters and structs for OMAP2+ as const, too.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Set internal clock source for MMC2 on tao3530.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Provide pdata-quirks for Am437x processor family.
Signed-off-by: NKeerthy <j-keerthy@ti.com>

Provide pdata-quirks for DRA7 processor family.
Signed-off-by: NNishanth Menon <nm@ti.com>

Provide pdata-quirks for OMAP5 processor family.
Signed-off-by: NNishanth Menon <nm@ti.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for OMAP3 ROM Random Number Generator via
pdata-quirks.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove pdata quirks for the displays on boards that are now supported
properly with DT.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

OMAP5 has the same iommus as OMAP4, so extend the OMAP4
iommu pdata quirks for OMAP5 as well.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP iommu driver performs the reset management for the
iommu instances in processor sub-systems using the omap_device
API which are currently supplied as platform data ops. Use pdata
quirks to maintain the functionality as the OMAP iommu driver
gets converted to use DT nodes, until the reset portions are
decoupled from omap_hwmod/omap_device into a separate reset
driver.

This patch adds the pdata quirks for the reset management of
iommus within the DSP (OMAP3 & OMAP4) and IPU subsystems (OMAP4).
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable the WiLink6 connected to mmc2.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.

Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

sbc-t3x boards features two external USB ports on SB-T35 baseboard.
The baseboardi USB hub reset signal should be de-asserted to make
those ports functional.

sbc-t3517 features additional (assembled on CoM) USB hub which also
requires reset signal handling.

Add quirks code to handle proper reset pulse signal.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for CM-T3517 CoM and SBC-T3517 board.

reused common support for sbc-t3x boards
(omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi):

* SB-T35 baseboard eth
* MMC1, UART3
* HS USB Port 1/2
* I2C1/3
* Heartbit led

Added basic support for:

* MMC1 wp/cd signals
* CM-T3517 Usb Hub
* WL12xx WiFi chip
* Davinci EMAC
* AM35X OTG
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for CM-T3530 CoM and SBC-T3530 board.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Refactor the sbc-t3x device tree as a preparation for additional
(sbc-t3530, sbc-t3517, etc.) boards support.

No functional changes.

The device tree will have the following structure:

omap3-cm-t3x.dtsi
 |
 |<-- omap3-cm-t3x30.dtsi
 |     |
 |     |
 |     |     -----                  -------          ------------
 |     |    | CoM |                | Board |        | Base board |
 |     |     -----                  -------          ------------
 |     |                                            omap3-sb-t35.dtsi
 |     |                                                  |
 |     |<-- omap3-cm-t3730.dts <-- omap3-sbc-t3730.dts -->|
 |     |                                                  |
 |     |<-- omap3-cm-t3530.dts <-- omap3-sbc-t3530.dts -->|
 |                                                        |
 |<-------- omap3-cm-t3517.dts <-- omap3-sbc-t3517.dts -->|
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

After splitting padconf core into two parts to avoid exposing
unaccessable registers, the new padconf core2 domain was left
without a wake-up interrupt.

Fix the issue by passing the shared wake-up interrupt in
platform data like we do for padconf core and wkup domains
already.

Fixes: 3d495383 (ARM: dts: Split omap3 pinmux core device)
Signed-off-by: NTony Lindgren <tony@atomide.com>

Without enabling the workaround for ARM errata 430973 thumb
compiled userland crashes randomly on the Nokia N900.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds support for CompuLab SBC-T3530, also known as cm-t3730:

http://compulab.co.il/products/sbcs/sbc-t3530/

It seems that with the sbc-3xxx mainboard is also used on
SBC-T3517 and SBC-T3730 with just a different CPU module:

http://compulab.co.il/products/sbcs/sbc-t3517/
http://compulab.co.il/products/sbcs/sbc-t3730/

So let's add a common omap3-sb-t35.dtsi and then separate SoC
specific omap3-sbc-t3730.dts, omap3-sbc-t3530.dts and
omap3-sbc-t3517.dts.

I've tested this with SBC-T3730 as that's the only one I have.
At least serial, both Ethernet controllers, MMC, and wl12xx WLAN
work.

Note that WLAN seems to be different for SBC-T3530. And SBC-T3517
may need some changes for the EMAC Ethernet if that's used
instead of the smsc911x.

Cc: devicetree@vger.kernel.org
Cc: Mike Rapoport <mike@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As the emac uses the system control module registers for
reset and interrupts, we need to pass those in the platform
data until we have a separate system control module driver.
Signed-off-by: NTony Lindgren <tony@atomide.com>

As we currently need to support a mix of legacy platform data and
device tree intialized data, let's make sure things keep working
for the TWL GPIOs.

Mostly the issue is caused by the fact that DSS does not yet have
device tree bindings, so we need to rely on the TWL GPIO callback
for setting up things like LCD backlight for some boards.

As of_platform_populate() for the TWL GPIO is called by twl-core
after the I2C bus has been initialized, we cannot pass the auxdata
table from the board init code to twl-core like we used to with
just legacy platform data.

So let's use the omap_device bus hook to patch in the platform
data for TWL GPIO until we have sorted out the issues with the
TWL GPIOs and device tree bindings.

The other option was be to initialize twl core using legacy
platform data, which seems like a step backwards as we're moving
to device tree only initialization.  And we really don't want to
add custom configuration functions to the TWL GPIO driver either
for this.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This allows us to keep things working when booted with
device tree. Note that we still need to initialize most
things with platform data as the drivers are lacking
support for device tree.
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like some boards need to fill in the auxdata before
we call of_platform_populate(). Let's add support for
auxdata quirks like we already have for pdata quirks for
legacy drivers.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like we need to configure the regulators and use the pdata
quirk to make eMMC work with device tree.

It seems that mostly vaux3 is used, and only some earlier revisions
used vmmc2. This has been tested to work on devices where the
system_rev passed by the bootloader has versions 0x0010, 0x2101
and 0x2204.

Cc: devicetree@vger.kernel.org
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NSebastian Reichel <sre@debian.org>
[tony@atomide.com: updated with pinctrl changes and comments from Sebastian]
Signed-off-by: NTony Lindgren <tony@atomide.com>

As the wl12xx bindings are still pending, this way we can
get things working for omap3 evm and zoom platforms.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Now pinctrl-single-omap can handle the wake-up events for us now
as long as the events are configured in the .dts files.

Done in collaboration with Roger Quadros <rogerq@ti.com>.

Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Prakash Manjunathappa <prakash.pm@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For few things we're still going to be needing platform
data for device tree based drivers. Let's set up auxdata
handling and do it in pdata-quirks.c so we have all the
legacy calls in one place.
Reviewed-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

IGEPv2 board has both an DVI and TFP410 video interfaces but
DSS support for DeviceTree has not yet landed in mainline so
is necessary to init the displays using legacy platform code.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Set internal clock source for MMC2 on N950/N9.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Let's use the platform data quirk support for wl12xx
and move the board specific code out of devices.c.
Signed-off-by: NTony Lindgren <tony@atomide.com>