The mpc836x_mds platform has been broken since the commit
6fe32649

  "netdev/phy: Use mdiobus_read() so that proper locks are taken"

which caused the fsl_pq_mdio TBI autoprobe to oops.  The oops
was "fixed" in commit 28d8ea2d

  "fsl_pq_mdio: Clean up tbi address configuration"

by simply removing the the autoscan code, and making tbi nodes
mandatory.  Some of the newer reference platforms were updated
to have tbi nodes in 22066949

  "powerpc: Add TBI PHY node to first MDIO bus"

but the older mpc836x didn't get one and hence was just failing
with -EBUSY as follows:

 fsl-pq_mdio: probe of e0102120.mdio failed with error -16
   ...
 net eth0: Could not attach to PHY
 eth0: Cannot initialize PHY, aborting.

Add a TBI node and use the 1st free address for it.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The Freescale serial port's are pretty much a 16550, however there are
some FSL specific bugs and features.  Add a "fsl,ns16550" compatiable
string to allow code to handle those FSL specific issues.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Simply add power management controller nodes and sleep properties.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add fsl,qe-num-riscs and fsl,qe-num-snums to all the devices trees which
have qe node.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The cell-index property isn't used on PCI nodes and is ill defined.
Remove it for now and if someone comes up with a good reason and
consistent definition for it we can add it back
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

- Update the device tree per QE USB bindings;
- Add timer (FSL GTM) node;
- Add gpio-controller node for BCSR13 bank (GPIOs on that bank
  are used to control the USB transceiver);
- Set up other BCSR registers;
- Configure the QE Par IO.

The work is loosely based on Li Yang's patch[1], which was used
to support peripheral mode only.

[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html

The s-o-b line of the original patch preserved here.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

We don't want to encourage the bogus device_type usage.

The device type isn't used in the code, so we can simply remove it from
the documentation and dts files.

Boards should specify proper compatible entries instead.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.

83xx pci nodes have this change:
    register properties now contain two address length tuples:
	First is the pci bridge register base, this has always been there.
	Second is the config base, this is new.

This is documented in dts-bindings/fsl/83xx-512x-pci.txt

The changes accomplish these things:
    mpc83xx_add_bridge no longer needs to call get_immrbase
    it uses hard coded addresses if the second register value is missing
Signed-off-by: NJohn Rigby <jrigby@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds the localbus node, moves the bcsr node into the
localbus node, and adds the flash node.

Also enable MTD support in the defconfig.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them.  Add same to platform probe code.

This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.

also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd44736: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Added DMA nodes for the elo/elo-plus DMA engines.

Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that
its the same as all the other boards.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

- get rid of `model = "UCC"' in the ucc nodes
  It isn't used anywhere, so remove it. If we'll ever need something
  like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
  Drivers are modified for backward compatibility's sake.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch converts the remaining 83xx boards to the dts-v1 format.
This includes the mpc8313_rdb, mpc832x_mds, mpc8323_rdb, mpc8349emitx,
mpc8349emitxgp and the mpc836x_mds.

The mpc8315_rdb mpc834x_mds, mpc837[789]_*, and sbc8349 were already
dts-v1 and only undergo minor changes for the sake of formatting
consistency across the whole group of boards; i.e.  the idea being
that you can do a "diff -u board_A.dts board_B.dts" and see something
meaningful.

The general rule I've applied is that entries for values normally
parsed by humans are left in decimal (i.e. IRQ, cache size, clock
rates, basic counts and indexes) and all other data (i.e. reg and
ranges, IRQ flags etc.) remain in hex.

I've used dtc to confirm that the output prior to this changeset
matches the output after this changeset is applied for all boards.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Currently there are several dts that don't specify address or size
cells for the muram.  This causes dtc to use default values, one of
which is an address-cells of two, and this breaks the parsing of the
muram ranges, which is assuming an address-cells of one. For example:

Warning (reg_format): "reg" property in
/qe@e0100000/muram@10000/data-only@0 has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 1)

Explicitly setting the address and size cells gets it parsed properly
and gets rid of the four dtc warnings.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Also:
- rename "fsl_spi" to "fsl,spi";
- add and use cell-index property, if found;
- split probing code out of fsl_spi_init, thus we can call
  it for legacy device_type probing and new "compatible" probing.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

device_type property is bogus, thus use proper compatible.

Also change compatible property to "fsl,ucc-mdio".
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".

Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Updates the ucc_geth device driver to check the new rx-clock-name and
tx-clock-name properties first.  If present, it uses the new function
qe_clock_source() to obtain the clock source.  Otherwise, it checks the
deprecated rx-clock and tx-clock properties.

Update the device trees for 832x, 836x, and 8568 to contain the new property
names only.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Added aliases nodes for kurobox, 83xx, 85xx, and 86xx platforms.
This included added labels and cell-index properties for serial and
pci nodes.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* Removed address fields in ethernet nodes
* Removed #address-cells, #size-cells from gianfar nodes
* Added cell-index to gianfar and ucc ethernet nodes
* Added enet[0..3] labels
* Renamed compatible node for gianfar mdio to "fsl,gianfar-mdio"
* Removed device_type = "mdio"

The matching for gianfar mdio still supports the old "mdio"/"gianfar" combo
but it is now considered deprecated.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* Removed device_type = "i2c"
* Added missing second I2C controller on MPC8548 CDS, MPC8544 DS
* Added #address-cells, #size-cells, and cell-index where missing
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Now the rtc class ds1374 driver has been added, remove the old rtc
driver hookup code, add rtc node to device trees, and turn on the
new driver in the defconfigs.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Updated the device trees to have the PCI nodes be at the same level as
the SOC node.  This is to make it so that the SOC nodes children address
space is just on chip registers and not other bus memory as well.

Also, for PCIe nodes added a P2P bridge to handle the virtual P2P bridge
that exists in the PHB.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Removed the following cruft from .dts files:
* 32-bit in cpu node -- doesn't exist in any spec and not used by kernel
* removed built-in (chrp legacy)
* Removed #interrupt-cells in places they don't need to be set
* Fixed ranges on lite5200*
* Removed clock-frequency from i8259 pic node, not sure where this came from
* Removed big-endian from i8259 pic nodes, this was just bogus
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Updated the 83xx & 85xx device tree PCI related compartible property.

Used the following compatible properties:
	PCI     "fsl,mpc8349-pci"
	PCI     "fsl,mpc8540-pci"
	PCI-X:  "fsl,mpc8540-pcix"
	PCIe:   "fsl,mpc8548-pcie"
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

For the 83xx, 85xx, and 86xx device trees, add a "local-mac-address" property
to every Ethernet node that didn't have one.  Add a comment indicating that
the "address" and/or "mac-address" properties are deprecated in DTS files
and will be removed at a later time.  Change all MAC address properties to
have a zero MAC address value.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

phy-connection-type now supersedes the interface property.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The #cpus property is unused and undocumented and is therefore
being removed.
Signed-off-by: NStuart Yoder <stuart.yoder@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The MPC836x PB board is really just one part of the MPC836x MDS.  We currently
name all other PB boards as MDS.  Removed all references to PB and replaced
with MDS.  Additionally renamed the .dts to match the defconfig (mpc836x_mds*).
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

* Fixed up top level compatible property for all boards
* Removed explicit linux,phandle usage. Use references and labels now
* Fixed interrupt sense attribute, some interrupts were marked edge, that are level
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The 'linux,boot-cpu' property is obsolete, so remove it from all of the DTS
files and from booting-without-of.txt.  The boot CPU is actually defined in
the device tree header, and U-Boot sets that field.  The device tree compiler
also complains if the property exists.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NStuart Yoder <stuart.yoder@freescale.com>
Acked-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add MPC8360EMDS default device-tree source file
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NJiang Bo <Tanya.jiang@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>