- 02 4月, 2009 4 次提交
-
-
由 Ramkrishna Vepa 提交于
This patch takes care of Initialization and configuration steps of Neterion Inc's X3100 Series 10GbE PCIe I/O Virtualized Server Adapter. - Device Initialization. - Verification and setting of device config parameters. - Allocation of Tx FIFO and Rx Ring descriptors (DTR). - APIs to get various type of hw stats - APIs to configure RTS (Receive Traffic Steering) - Changes in this submission - - Include vmalloc header without which a compilation error occured on sparc64, ppc64 and IA64 plaforms. - Fixed compilation warning in register_poll, write32_upper, write32_lower and the special write64 functions on ppc64. - General cleanup - removed redundant includes and defines. - Changes in previous submissions - - Add readq/writeq implementation for the driver for 32 bit systems - reported by Dave Miller. - Incorporated following comments from Ben Hutchings - Start a comment with "/**" to make it a kernel-doc comment. - Use prefix, "__vxge" in front of hw functions to make them globally unique. - Fixed unnecessary clearing members of *channel just before freeing - Use backslashes only for macro definitions and not in multi-line statements. - Used pci_find_capability instead of redefining it. - Used device and revision ids that are already in pdev - no need to read them again. - Used pci_save_state() and pci_restore_state() around resets. - Used udelay and mdelay directly instead of wrapper. - In __vxge_hw_device_register_poll() reset i to 0 after the microsecond delay loop to commence the millisecond delay loop. - Corrected spelling "sapper" - should be "swapper" - Remove too much vertical whitespace. - Replaced magic numbers with appropriate macros - Incorporated following comments from Andi Kleen [andi@firstfloor.org] - Reduced the arguments in functions or refactored them into smaller functions. - Allocate page sized memories used in slow path with vmalloc. - Use asserts where necessary. - Use macros instead of magic numbers. - Use the pci layer code instead of defining own functions - Remove driver wrappers such as xge_hw_device_private_set(). - Fixed sparse warnings. Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com> Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com> Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ramkrishna Vepa 提交于
- Complete Register map details of Neterion Inc's X3100 Series 10GbE PCIe I/O Virtualized Server Adapter. - No change from previous submission. - Changes in previous submissions - - Incorporated following comments from Ben Hutchings - Use original macros for endian checks - Remove VXGE_OS_PLATFORM_* macros as they are unused. - Converted multiple bVALX macros into single with additional width parameter and renamed it to vxge_bVALn. - Using __packed instead of pragma pack(1) - Added a comment of the use of a hw swapper so driver code is portable (does not have to change the byte order for register access as well as dma operations) on different ENDIAN platforms. - Using the <linux/pci_regs.h> definitions instead of redefing them. - Using the PCI capabilities registers in <linux/pci_regs.h> instead of redefing them. Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com> Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com> Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ramkrishna Vepa 提交于
- update to Maintainer list of S2IO 10GbE drivers (xframe/vxge). Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com> Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com> Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ramkrishna Vepa 提交于
- vxge driver help text file. - No change from previous submission. - Changes in previous submissions - Removed the performance tuning section with instructions to disable time stamps and change sysctl settings - Reported by Dave Miller General clean up. - Removed tx/rx_pause, exec_mode, tx_steering_type, rx_steering_type, gro, intr_type, rx & tx max_indicate_pkts and exec_mode loadable parameters. The driver default settings work well in most if not all cases. Another patch to configure these parameters with ethtool will be released in the future - Reported by Stephen Hemminger. - Incorporated following fixes based on comments from Ben Hutchings Removed references to earlier kernel versions. Removed sections that are similar for all drivers - Load/Unload Identifying the adapter/interface Boot time configuration Removed loadable parameter - NAPI - Napi is always enabled. rx_steering_type & ring_blocks - The driver default settings work well in most if not all cases. Another patch to configure these parameters with ethtool will be released in the future. Removed ethtool support section - No need to duplicate ethtool docs here. Removed Known Issue on SUSE 9 - Doesn't apply when using a current kernel. Removed Common Problems section - These don't apply to in-tree modules. Removed Available Downloads section - Not sure this belongs in-tree. Removed Copyright information - This notice doesn't belong in the kernel. Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com> Signed-off-by: NRastapur Santosh <santosh.rastapur@neterion.com> Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 4月, 2009 5 次提交
-
-
由 Ben Hutchings 提交于
If we use a shared legacy IRQ then our interrupt handler may be called as soon as it is registered even though IRQs are disabled on the NIC. Now that the legacy interrupt handler also checks for event delivery, it may decide to schedule polling in this case. Ensure that the NAPI context is valid but disabled at this point. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wei Yongjun 提交于
Remove pointless conditional before kfree(). Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Rami Rosen 提交于
Signed-off-by: NRami Rosen <ramirose@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Heiko Carstens 提交于
Let driver depend on HAS_IOMEM to avoid build breakage on s390: CC drivers/net/ethoc.o drivers/net/ethoc.c: In function 'ethoc_read': drivers/net/ethoc.c:221: error: implicit declaration of function 'ioread32' drivers/net/ethoc.c: In function 'ethoc_write': drivers/net/ethoc.c:226: error: implicit declaration of function 'iowrite32' drivers/net/ethoc.c: In function 'ethoc_rx': drivers/net/ethoc.c:405: error: implicit declaration of function 'memcpy_fromio' drivers/net/ethoc.c: In function 'ethoc_start_xmit': drivers/net/ethoc.c:828: error: implicit declaration of function 'memcpy_toio' Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Acked-by: NThierry Reding <thierry.reding@avionic-design.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 3月, 2009 5 次提交
-
-
由 Jaswinder Singh Rajput 提交于
Added osi_load_firmware() instead of copying same thing twice Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
-
由 Jaswinder Singh Rajput 提交于
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
-
由 Jaswinder Singh Rajput 提交于
Added predef variable in add_mcs() to support predefined mcs data Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
-
由 Alexander Beregalov 提交于
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Pablo Neira Ayuso 提交于
This patch fixes a dependency with IPv6: ERROR: "__ipv6_addr_type" [net/netfilter/xt_cluster.ko] undefined! This patch adds a function that checks if the higher bits of the address is 0xFF to identify a multicast address, instead of adding a dependency due to __ipv6_addr_type(). I came up with this idea after Patrick McHardy pointed possible problems with runtime module dependencies. Reported-by: NSteven Noonan <steven@uplinklabs.net> Reported-by: NRandy Dunlap <randy.dunlap@oracle.com> Reported-by: NCyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 3月, 2009 26 次提交
-
-
由 David S. Miller 提交于
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
We can't put 'mdio' until after we've used it in the fsl_pq_mdio_bus_name() call. Also fix error return values. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
We can't put 'mdio' until after we've used it in the fsl_pq_mdio_bus_name() call. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Harvey Harrison 提交于
All users have been removed. Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Harvey Harrison 提交于
Allows for the removal of byteswapping in some places and the removal of HIPQUAD (replaced by %pI4). Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Harvey Harrison 提交于
dcc_ip is treated as a host-endian value in the first printk, but the second printk uses %pI4 which expects a be32. This will cause a mismatch between the debug statement and the warning statement. Treat as a be32 throughout and avoid some byteswapping during some comparisions, and allow another user of HIPQUAD to bite the dust. Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Beregalov 提交于
drivers/net/hamradio/dmascc.c:587: error: 'struct net_device' has no member named 'set_mac_address' Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Herbert Xu 提交于
When GRO/frag_list support was added to GSO, I made an error which broke the support for segmenting linear GSO packets (GSO packets are normally non-linear in the payload). These days most of these packets are constructed by the tun driver, which prefers to allocate linear memory if possible. This is fixed in the latest kernel, but for 2.6.29 and earlier it is still the norm. Therefore this bug causes failures with GSO when used with tun in 2.6.29. Reported-by: NJames Huang <jamesclhuang@gmail.com> Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Randy Dunlap 提交于
Add missing struct field to fix kernel-doc warning: Warning(include/linux/skbuff.h:182): No description found for parameter 'flags' Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Beregalov 提交于
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://jdelvare.pck.nerim.net/jdelvare-2.6由 Linus Torvalds 提交于
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: i2c-core: Some style cleanups i2c-piix4: Add support for the Broadcom HT1100 chipset i2c-piix4: Add support to SB800 SMBus changes i2c-pca-platform: Use defaults if no platform_data given i2c-algo-pca: Use timeout for checking the state machine i2c-algo-pca: Rework waiting for a free bus i2c-algo-pca: Add PCA9665 support i2c: Adapt debug macros for KERN_* constants i2c-davinci: Fix timeout handling i2c: Adapter timeout is in jiffies i2c: Set a default timeout value for all adapters i2c: Add missing KERN_* constants to printks i2c-algo-pcf: Handle timeout correctly i2c-algo-pcf: Style cleanups eeprom/at24: Remove EXPERIMENTAL i2c-nforce2: Add support for MCP67, MCP73, MCP78S and MCP79 i2c: Clarify which clients are auto-removed i2c: Let checkpatch shout on users of the legacy model i2c: Document the different ways to instantiate i2c devices
-
由 Linus Torvalds 提交于
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits) [ARM] 5435/1: fix compile warning in sanity_check_meminfo() [ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx [ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0 [ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins imxfb: Fix TFT mode i.MX21/27: remove ifdef CONFIG_FB_IMX imxfb: add clock support mxc: add arch_reset() function clkdev: add possibility to get a clock based on the device name i.MX1: remove fb support from mach-imx [ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined Gemini: Add support for Teltonika RUT100 Gemini: gpiolib based GPIO support v2 MAINTAINERS: add myself as Gemini architecture maintainer ARM: Add Gemini architecture v3 [ARM] OMAP: Fix compile for omap2_init_common_hw() MAINTAINERS: Add myself as Faraday ARM core variant maintainer ARM: Add support for FA526 v2 [ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h [ARM] collie: fix two minor formatting nits ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arjan/linux-2.6-async-for-30由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/arjan/linux-2.6-async-for-30: fastboot: remove duplicate unpack_to_rootfs() ide/net: flip the order of SATA and network init async: remove the temporary (2.6.29) "async is off by default" code Fix up conflicts in init/initramfs.c manually
-
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: Blackfin arch: be less noisy when gets a gpio conflict after kernel has booted Blackfin arch: add RSI's definitions to bf514 and bf516 Blackfin arch: add link-time asserts to make sure on-chip regions dont overflow Blackfin arch: sport spi needs 6 gpio pins Blackfin arch: add sport-spi related resource stuff to board file Blackfin arch: Blacklist Hibernate (PM_SUSPEND_MEM) on BF561 as well Blackfin arch: Privide BF537-STAMP platform data of ADP5520 Multifunction driver Blackfin arch: enable the platfrom PATA driver with CF Cards Blackfin arch: clean up sports header file Blackfin arch: convert BF5{18,27,48}_FAMILY to CONFIG_BF{51,52,54}x Blackfin arch: bf51x processors also have 8 timers Blackfin arch: add a check to make sure only Blackfin GPIOs may generate IRQs Blackfin arch: update default kernel configuration Blackfin arch: include linux headers that this one uses definitions from fro sport drivers
-
由 Linus Torvalds 提交于
Merge branch 'percpu-cpumask-x86-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'percpu-cpumask-x86-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (682 commits) percpu: fix spurious alignment WARN in legacy SMP percpu allocator percpu: generalize embedding first chunk setup helper percpu: more flexibility for @dyn_size of pcpu_setup_first_chunk() percpu: make x86 addr <-> pcpu ptr conversion macros generic linker script: define __per_cpu_load on all SMP capable archs x86: UV: remove uv_flush_tlb_others() WARN_ON percpu: finer grained locking to break deadlock and allow atomic free percpu: move fully free chunk reclamation into a work percpu: move chunk area map extension out of area allocation percpu: replace pcpu_realloc() with pcpu_mem_alloc() and pcpu_mem_free() x86, percpu: setup reserved percpu area for x86_64 percpu, module: implement reserved allocation and use it for module percpu variables percpu: add an indirection ptr for chunk page map access x86: make embedding percpu allocator return excessive free space percpu: use negative for auto for pcpu_setup_first_chunk() arguments percpu: improve first chunk initial area map handling percpu: cosmetic renames in pcpu_setup_first_chunk() percpu: clean up percpu constants x86: un-__init fill_pud/pmd/pte x86: remove vestigial fix_ioremap prototypes ... Manually merge conflicts in arch/ia64/kernel/irq_ia64.c
-
由 Zhenwen Xu 提交于
Some lines over 80. The printk(KERN_ERR ... ) should be dev_err. And some blankspace should be deleted. Signed-off-by: NZhenwen Xu <helight.xu@gmail.com> Signed-off-by: NJean Delvare <khlai@linux-fr.org>
-
由 Flavio Leitner 提交于
Add support for the Broadcom HT1100 LD chipset (SMBus function.) Signed-off-by: NFlavio Leitner <fbl@redhat.com> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Shane Huang 提交于
Add support for the AMD SB800 Family series of products. Major changes include the changes to addressing the SMBus registers at different location from the locations in the previous compatible parts from AMD such as SB400/SB600/SB700. For SB800, the main features and register definitions of SMBus and other interfaces are still compatible with the previous products with the only change being in how to access the internal registers for these blocks. Signed-off-by: NShane Huang <shane.huang@amd.com> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Wolfram Sang 提交于
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Wolfram Sang 提交于
We now timeout also if the state machine does not change within the given time. For that, the driver-specific completion-functions are extended to return true or false depending on the timeout. This then gets checked in the algorithm. Signed-off-by: NWolfram Sang <w.sang@pengutronix.de> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Wolfram Sang 提交于
Waiting for a free bus now accepts the timeout value in jiffies and does proper checking using time_before. Signed-off-by: NWolfram Sang <w.sang@pengutronix.de> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Marco Aurelio da Costa 提交于
Add support for the PCA9665 I2C controller. Signed-off-by: NWolfram Sang <w.sang@pengutronix.de> Signed-off-by: NJean Delvare <khali@linux-fr.org>
-
由 Frank Seidel 提交于
According to kerneljanitors todo list all printk calls (beginning a new line) should have an according KERN_* constant. Those are the changes to the debug macros in the i2c subsystem to meet this requirement. Also changing no-debug statements to raw printks again. Signed-off-by: NFrank Seidel <frank@f-seidel.de> Signed-off-by: NJean Delvare <khali@linux-fr.org> Tested-by: NWolfram Sang <w.sang@pengutronix.de>
-
由 Jean Delvare 提交于
Properly set the adapter timeout value in jiffies, and then use that value in the driver, rather than a hard-coded constant. Signed-off-by: NJean Delvare <khali@linux-fr.org> Tested-by: NTroy Kisky <troy.kisky@boundarydevices.com> Cc: Kevin Hilman <khilman@mvista.com>
-