In a similar fashion to the previous patch, allow bridges and VLAN
devices on top of bridges to be enslaved to a VRF master device.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow port netdevs, LAG and VLAN devices stacked on top of these to be
enslaved to a VRF master device.

Upon enslavement, create a router interface (RIF) for the enslaved
netdev and associate it with a virtual router (VR) based on the VRF's
table ID.

If a RIF already exists for the netdev (f.e., due to the existence of an
IP address), then it's deleted and a new one is created with the
appropriate VR binding.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for TC flower offload statistics including number of packets,
bytes and last use timestamp. Currently the statistics are gathered on a
per-rule basis.
Signed-off-by: NArkadi Sharshvesky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for allocating generic flow counter. Generic flow counter
can count packets or packets and bytes and can be assigned to different
hardware processes. First use will be for counting packets and bytes of
ACL rules, and will be introduced in the following patches.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add implementation for counter allocator. The ASIC has special memory
pool for various counting purposes. Counter memory is distributed between
equal size banks.

The static sub-pool configuration should specify the following parameters
for each sub-pool:
- Number of required banks.
- Maximum entry size.

Each module can add dedicated sub-pool or use existing one.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The inetaddr notification block is currently implemented in the main
driver file, but this isn't really appropriate, as it mainly creates and
destroys router interfaces (RIFs) which belong with the rest of the
router code.

This will become even more apparent later on when we'll need to bind
these RIFs to virtual routers according to the VRF's table.

Structure the driver better and prevent unnecessary function exports by
moving the RIF related code with the rest of the router code.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We only use the RIF reference count to determine when the last IP
address was removed, but instead we can just test 'in_dev->ifa_list'.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VLAN device is configured on top of a LAG device (f.e.,
bond0.10), a vPort is created on top of each of the LAG's slaves and its
'dev' pointer is set to the VLAN device.

This is in contrast to the implicit PVID vPort (representing 'bond0'),
whose 'dev' pointer keeps pointing to the port netdev itself (f.e.,
'sw1p1').

Make both cases consistent by setting their 'dev' pointer to the actual
netdev they represent. Either the LAG device itself (in the case of the
PVID vPort) or the VLAN device on top of it.

This will later allow us to more easily understand for which netdev we
should create the router interface (RIF) upon enslavement to a VRF
master.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an upper device is configured on top of a vPort we make sure it's a
bridge master during PRECHANGEUPPER and fail otherwise. Therefore, when
CHANGEUPPER is later received we don't bother checking the upper's type.

Make the code more extendable in preparation for VRF uppers, by checking
the upper's type.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We're going to allow bridges stacked on top of port netdevs to be
enslaved to a VRF, but for now, only VLAN uppers of the VLAN-aware
bridge are supported.

Sanitize any other bridge upper. This is consistent with the way we
sanitize port netdevs' uppers.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit dd82364c ("mlxsw: Flip to the new dev walk API") did some
small changes in mlxsw code, but it did not respect the naming
conventions. So fix this now.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Point back the unregister IPv6 mc table to the bc table.
It is done since IPv6 mcast snooping is not supported for Spectrum yet.
Reported-by: NJiri Pirko <jiri@mellanox.com>
Fixes: 71c365bd ("mlxsw: spectrum: Separate bc and mc floods")
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Tested-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The decision whether to flood a multicast packet to a port dependent
on three flags: mc_disabled, mc_router_port, mc_flood.

If mc_disabled is on, the port will be flooded according to mc_flood,
otherwise, according to mc_router_port. To accomplish that, add those
flags into the mlxsw_sp_port struct and update the mc flood table
accordingly.

Update mc_router_port by switchdev attribute
SWITCHDEV_ATTR_ID_PORT_MC_ROUTER_PORT.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Break the bm (broadcast-multicast) into two tables, one for broadcast
(and link local multicast that behaves like bc) and one for unknown
multicasts.
Add a bool into mlxsw_sp_port named mc_flood that reflect the value this
port should have in the mc flood table (currently, always 1);
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the last IP address is removed from a netdev, its RIF is deleted.
However, if user didn't first remove neighbours and nexthops using this
interface, then they would still be present in the device's tables.

Therefore, whenever a RIF is deleted, make sure all the neighbours and
nexthops (adjacency entries) using it are removed from the relevant
tables as well.

The action associated with any route using this RIF would be refreshed,
most likely to trap. If the kernel decides to remove the route (f.e.,
because all the nexthops are now DEAD), then an event would be sent,
causing the route to be removed from the device.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now we had two interfaces for neighbour related configuration:
ndo_neigh_{construct,destroy} and NEIGH_UPDATE netevents. The ndos were
used to add and remove neighbours from the driver's cache, whereas the
netevent was used to reflect the neighbours into the device's tables.

However, if the NUD state of a neighbour isn't NUD_VALID or if the
neighbour is dead, then there's really no reason for us to keep it
inside our cache. The only exception to this rule are neighbours that
are also used for nexthops, which we periodically refresh to get them
resolved.

We can therefore eliminate the ndo entry point into the driver and
simplify the code, making it similar to the FIB reflection, which is
based solely on events. This also helps us avoid a locking issue, in
which the RIF cache was traversed without proper locking during
insertion into the neigh entry cache.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the existing setup_tc ndo call and allow to offload cls_flower
rules. Only limited set of dissector keys and actions are supported now.
Use previously introduced ACL infrastructure to offload cls_flower rules
to be processed in the HW.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ACL core infrastructure for Spectrum ASIC. This infra provides an
abstraction layer over specific HW implementations. There are two basic
objects used. One is "rule" and the second is "ruleset" which serves as a
container of multiple rules. In general, within one ruleset the rules are
allowed to have multiple priorities and masks. Each ruleset is bound to
either ingress or egress a of port netdevice.

The initial TCAM implementation is very simple and limited. It utilizes
parman lsort manager to take care of TCAM region layout.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using the MPSC register, add the functions that configure port-based
packet sampling in hardware and the necessary datatypes in the
mlxsw_sp_port struct. In addition, add the necessary trap for sampled
packets and integrate with matchall offloading to allow offloading of the
sample tc action.

The current offload support is for the tc command:

tc filter add dev <DEV> parent ffff: \
	  matchall skip_sw \
	  action sample rate <RATE> group <GROUP> [trunc <SIZE>]

Where only ingress qdiscs are supported, and only a combination of
matchall classifier and sample action will lead to activating hardware
packet sampling.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During transmission the skb is checked for headroom in order to
add vendor specific header. In case the skb needs to be re-allocated,
skb_realloc_headroom() is called to make a private copy of the original,
but doesn't release it. Current code assumes that the original skb is
released during reallocation and only releases it at the error path
which causes a memory leak.

Fix this by adding the original skb release to the main path.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As ENOTSUPP is specific to NFS, change the return error value to
EOPNOTSUPP in various places in the mlxsw driver.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the order of the free directives to match the port init function
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the mlxsw spectrum driver only supports offloading the matchall
classifier together with the mirred action. To allow more matchall tc
offloads, make the code symmetric so that it can be easily extended later
on for other actions.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.

Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a port is split we should mark it as such, as otherwise the split
ports aren't renamed correctly (e.g. sw1p3 -> sw1p3s1) and the unsplit
operation fails:

$ devlink port split sw1p3 count 4
$ devlink port unsplit eth0
devlink answers: Invalid argument
[  598.565307] mlxsw_spectrum 0000:03:00.0 eth0: Port wasn't split

Fixes: 67963a33 ("mlxsw: Make devlink port instances independent of spectrum/switchx2 port instances")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NTamir Winetroub <tamirw@mellanox.com>
Reviewed-by: NElad Raz <eladr@mellanox.com>
Tested-by: NTamir Winetroub <tamirw@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure policers and connect them to trap groups.

While many trap groups share policer's configuration they don't share
the actual policer because each trap group represents a different
flow / protocol and we don't want one of them to be able to exceed its
rate on behalf of another.
For example, if STP and LLDP gets to send 128 packets/sec each, if we
put them in one 256 packets/sec policer, one can send 200 packets while
the other only 50.

Note that IP2ME covers lots of flows, so it's limit is set to match the
cpu ability to handle data.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trap groups can be used to control traps priority, both in terms of
which trap "wins" if a packet matches two traps (priority) and in terms
of packets from which trap group will be scheduled to the cpu first (tc).
They can also be used to set rate limiters (policers) on them (will be
added in the next patches).

Currently, we support two trap groups. In Spectrum we want a better
resolution, so every protocol / flow will have a different trap group,
so we can control its parameters separately. Once the policers will be
implemented, it will also allow us limit the rate of each protocol by
itself.

This patch change the trap group list to include:
* the emad trap group, which is shared for all the devices.
* Switchx2's trap groups, which are a copy of the current trap groups.
* Spectrum's new trap groups, in order to match the above guidelines.
(Switchib is using only the emad trap group, so it require no changes).

This patch also includes new configuration for Spectrum's trap groups,
with primary priority order within them.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a trap for BGP protocol that was previously trapped by the generic trap
for IP2ME. This trap will allow us to have better control (over priority
and rate) of the traffic.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trap groups have many options which we currently set to default values.
In the next patches we will use many of them with non-default values.

Some of these options have no default value, so this patch sets them as
params for the trap group set function. Others almost always use the same
values, so the set function will use this default values. In the rare cases
when they will need to be with other values, these values can be set
directly (using the macros for fields in registers).

Parameters without default value:
TC - the traffic class for packets that hit this trap group.
    (old default is the max tc)
priority - if one packet hits multiple trap groups, the group with the
	   higher priority will "catch" it. (old default is 0)
policer - limit rate policer (old default is disabled)

Default parameters:
swid - switch id, relevant for the emad trap only, ignored on Spectrum.
       (new default is 0)
rdq - CPU receive descriptor queue (new default is identical to trap
      group id)
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the emad trap init was done in the core. In the future we will
want to add some changes to the traps groups, according to device type.
This commit create a driver function to create the trap group for the
emad, so later it can be changed by devices. It also changes the emad
registration to use the new generic functions.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, we set the trap group to pre-determined option, based on whether
it is an rx or event trap.
This commit adds a possibility to chose the trap group, so it can be set
to different values in the following patches.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change trap setting function so instead of determining the trap group by
trap id, it gets it as a parameter (so later we can have different trap
groups for Spectrum and Switchx2).
Add "is_ctrl" parameter to the trap setting function. It control whether
the trapped packets wait in a designated control buffer or in their
default one. This parameter is ignored by Switchx2 and Switchib.
Add these parameters to the traps array in Spectrum, Switchx2 and
Switchib.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the events to use the generic listener struct.
Merge the event list into the trap list, so the same functions will
handle both.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the old rx listener struct definitions by the generic ones.
Use the new generic registering / unregistering functions for them.
Add some macros to organize the trap list.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 99724c18 ("mlxsw: spectrum: Introduce support for
router interfaces") we no longer rely on flooding traffic to the CPU in
order to trap packets intended for the host itself. Therefore, the FDB
MC trap can be removed.
Remove traps for protocols that are not supported yet.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers would need to check few internal matters for
that. To be used in downstream mlx5 commit.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When binding port to a newly created span entry, its refcount is
initialized to zero even though it has a bound port. That leads
to unexpected behaviour when the user tries to delete that port
from the span entry.

Fix this by initializing the reference count to 1.

Also add a warning to put function.

Fixes: 763b4b70 ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove including <generated/utsrelease.h> that don't need it.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we are about to introduce IB port APIs, we will add prefixes to
existing APIs.
Signed-off-by: NElad Raz <eladr@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, devlink register/unregister is done directly from
spectrum/switchx2 port create/remove functions. With a need to
introduce a port type change, the devlink port instances have to be
persistent across type changes, therefore across port create/remove
function calls. So do a bit of reshuffling to achieve that.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NElad Raz <eladr@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>