Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ...  among other things, it can be some time before
a driver is ready.  This patch corrects that oversight, fixing

 - documentation
 - platforms supporting the GPIO interface
 - users of that call (just one for now, others are pending)

There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.

Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ...  so those chips might not avoid the glitches.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Acked-by: NMilan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The new gpio_direction_input() and gpio_direction_output() functions
were both enabling output mode.  When configuring a GPIO for input mode,
you need to program the ODR (Output Disable Register).
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Cleanup of at91 platform level gpio wake and suspend/resume logic.

The GPIO core now delegates wakeups to the parent AIC by refcounting,
and delegates clock management to the clock API.  This makes these
system modules more independent of each other, which is cleaner and will
also help with the AT91SAM9263 (where some GPIO controllers share the
same irq and clock).

Original patch by David Brownell.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch updates the drivers (and other files) which include the
hardware headers.  This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).

The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h.  Renamed it to at91_pdc.h
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

set_irq_chipdata -> set_irq_chip_data
get_irq_chipdata -> get_irq_chip_data
do_level_IRQ -> handle_level_irq
do_edge_IRQ -> handle_edge_irq
do_simple_IRQ -> handle_simple_irq
irqdesc -> irq_desc
irqchip -> irq_chip
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch makes the AT91 gpio.c support processor-generic (AT91RM9200
and AT91SAM9xxx).  The GPIO controllers supported by a particular AT91
processor are defined in the processor-specific file and are registered
with gpio.c at startup.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is more preparation for adding support for the new Atmel AT91SAM9
processors.

Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from David Brownell

ARM genirq cleanups/updates:

    - Start switching platforms to newer APIs
        * use "irq_chip" name, not "irqchip"
        * providing irq_chip.name

    - Show irq_chip.name in /proc/interrupts, like on x86.

This update a bit more than half of the ARM code.  The irq_chip.name
values were chosen to match docs (if I have them) or be otherwise
obvious ("FPGA", "CPLD", or matching the code).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Thomas Gleixner

From: Thomas Gleixner <tglx@linutronix.de>

Fixup the conversion to generic irq subsystem.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch adds suspend/resume/set_wake support for the AT91RM9200's
GPIO interrupts.

Original patch from David Brownell.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In all current use cases, "chipdata" is used to store an iomem address.
Mark it with __iomem, and rename it to 'base'.  Leave the accessor macros
alone.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

disable_irq() lazily disables the interrupt, so the IRQ is only disabled
once the interrupt occurs again.  The GPIO interrupt handler therefore
must first check disable_depth to see if the IRQ needs to be disabled.

Orignal patch by Bill Gatliff.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch adds the at91_set_multi_drive() function to enable/disable
the multi-drive (open collector) pin capability on the AT91RM9200
processor.

This is necessary to fix the UDC (USB Gadget) driver for the AT91RM9200
board as it will not allow the board reset line to be pulled low if the
pullup is not driven as an open collector output as the boards are wired
to the USB connector on both the DK/EK.

This version of the patch updates it to 2.6.16-rc4.
Orignal patch by Jeff Warren.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from SAN People

Following changes were made to clock.c:

1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.

Otherwise it's the same as the previous patch.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>