Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Clean up the code to make it more readable:
* Remove reg_ and new_ prefixes from variable names, they made the
  names longer, causing extra line breaks, while not adding much
  value.
* Introduce struct device dev* = &client->dev in two functions, to
  avoid repeating client->dev everywhere in these functions.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

With some configuration option combinations, we get the following
warnings:

drivers/hwmon/lm90.c: In function 'lm90_detect':
drivers/hwmon/lm90.c:1114: warning: 'chip_id' may be used uninitialized
in this function
drivers/hwmon/lm90.c:1114: warning: 'reg_config1' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1114: warning: 'reg_convrate' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1187: warning: 'reg_emerg2' may be used
uninitialized in this function
drivers/hwmon/lm90.c:1187: warning: 'reg_status2' may be used
uninitialized in this function

We can solve these easily by reading the register values first and
checking for errors later. These errors should be very rare, even in
the case of failed detection, so this change has no impact on
performance. And this makes checkpatch.pl happier.
Reported-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Preallocate a buffer for the response to sensor reads, and reuse it
for each read instead of allocating a new one each time. This should
be faster and should also avoid memory fragmentation.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NDarrick J. Wong <djwong@us.ibm.com>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

There is no good reason that I can see why the failure to initialize
one instance should prevent other instances from being initialized.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NDarrick J. Wong <djwong@us.ibm.com>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

I am under the impression that error paths in functions
aem_init_aem1_inst() and aem_init_aem2_inst() are incorrect. In
several cases, the function returns 0 on error, which I suspect is
not intended. Fix this by properly tracking error codes.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NDarrick J. Wong <djwong@us.ibm.com>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Word reads can cause trouble with some I2C devices, so do as much
detection as we can using only byte reads, and only use a word read in
the end to confirm the positive match. Also properly handle read
errors.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Cc: Robert Casanova <robertcasanova@nanometrics.ca>

A modprobe of hwmon drivers that read/write ISA addresses on a powerpc results
in a kernel Oops. These reads/writes are being done via the inb()/in_8() and
outb()/out_8() macros.

Prevent these drivers from being built for powerpc.
Signed-off-by: NDean Nelson <dnelson@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add code to detect UE in case of Lancer.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Indicate to HW that the CQ is cleaned up before posting new RX buffers.
This prevents the HW to go into CQ full error condition.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If user tries to disable multicast promiscous mode, the adapter remains
in this mode as resetting the multicast promiscous mode was missing
in RX filter command. Fixed this.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use cpu_to_le32() for mcast_num field in RX filter command as this
field is of type u32.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sb_edac driver is marginally useful on a 32-bit kernel, and
currently has 64-bit divide compile errors when building that config.
For now, make this build on only for 64-bit kernels.
Signed-off-by: NJosh Boyer <jwboyer@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Returning the max traffic classes on get requests simplifies
user space configurations because applications will know
explicitly how many traffic classes can be used.

Typical switch implementations use 2 or 3 traffic classes
so this not seen often today. And user space can learn
the number of traffic classes by return codes but this
allows user space to configure ixgbe correctly at the
start.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes some issues found in the buffer read portion of
ixgbe_host_interface_command()

- use `bi` as the buffer index counter instead of `i`
- add conversion to native cpu byte ordering on register read
- fix conversion from bytes to dword
- use dword_len instead of buf_len when reading the register
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Wrap SR-IOV specific functions in CONFIG_PCI_IOV to avoid compiler
warnings.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_ieee_ets and ixgbe_ieee_pfc are intialized at
the same time. Do a check for both before configuring
IEEE802.1Qaz. Also max_frame was causing a sparse
warning resolved here as well.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

register_netdev() calls ndo_set_features() which may result in HW reset
which in turn will bring the laser back up.

This patch moves ixgbe_laser_tx_disable() below register_netdev()
in ixgbe_probe() to make sure laser is shut off on load.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Interface fails to obtain link on 82599 SFP in the following scenario:

1. Set advertised speed to GB:
ethtool -s eth0 advertise 0x20

2. Bring interface down
ip link set eth0 down

3. Issue any command that leads to a reset:
ethtool -t eth0

4. Bring link back up:
ip link set eth0 up

Following patch makes sure that the driver flaps the Tx laser every time
ixgbe_start_hw() is called, and not only when the speed is set.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PHY cable length unit detection was not using the correct
the correct PHY data variable for I347AT4.
Signed-off-by: NTomasz Kantecki <tomasz.kantecki@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

e100 parts don't support vlan offload but they generally do
allow use of vlans in higher software layers via the 8021q module.
That said, there are a couple of really old revisions of e100
hardware that don't even allow the longer frame sizes
required for vlan use with standard MTU.

Use the VLAN_CHALLENGED flag to prevent vlan binding to these
devices.
Reported-by: NMichael Tokarev <mjt@tls.msk.ru>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: David Lamparter <equinox@diac24.net>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This debugging message was recently added but it does not need to be as
alarming as a WARN.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix typo in code comment.
Signed-off-by: NRakib Mullick <rakib.mullick@gmail.com>
Acked-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In vmballoon_reserve_page(), flags has been passed from the callee
function (vmballoon_inflate here).  So, we can determine can_sleep outside
the loop.
Signed-off-by: NRakib Mullick <rakib.mullick@gmail.com>
Acked-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Interrupting w1_delay() in w1_read_bit() results in missing the low level
on the w1 line and receiving "1" instead of "0".

Add local_irq_save()/local_irq_restore() around the critical section
Signed-off-by: NJan Weitzel <j.weitzel@phytec.de>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When using multiple masters, w1_int.c would use the .init_name from w1.c
for all entities, which will fail when creating a corresponding sysfs
entry.  This patch uses the unique name previously generated.

  WARNING: at fs/sysfs/dir.c:451 sysfs_add_one+0x48/0x64()
  sysfs: cannot create duplicate filename '/devices/w1 bus master'
  Modules linked in:
  Call trace:
   [<9001a604>] warn_slowpath_common+0x34/0x44
   [<9001a64c>] warn_slowpath_fmt+0x14/0x18
   [<90078020>] sysfs_add_one+0x48/0x64
   [<900784ec>] create_dir+0x40/0x68
   [<9007857a>] sysfs_create_dir+0x66/0x78
   [<900c1a8a>] kobject_add_internal+0x6e/0x104
   [<900c1bc0>] kobject_add_varg+0x20/0x2c
   [<900c1c1c>] kobject_add+0x30/0x3c
   [<900dbd66>] device_add+0x6a/0x378
   [<900dbb4a>] device_initialize+0x12/0x48
   [<900dc080>] device_register+0xc/0x10
   [<900f99be>] w1_add_master_device+0x162/0x274
   [<90008e7a>] w1_gpio_probe+0x66/0xb4
   [<9000030c>] kernel_init+0x0/0xe8
   [<900dde54>] platform_drv_probe+0xc/0xe
   [<9000030c>] kernel_init+0x0/0xe8
   [<900dd4f8>] driver_probe_device+0x6c/0xdc
   [<900dd5fc>] __driver_attach+0x34/0x48
   [<900dcce8>] bus_for_each_dev+0x2c/0x48
   [<900dd5c8>] __driver_attach+0x0/0x48
   [<900dd38c>] driver_attach+0x10/0x14
   [<900dd16a>] bus_add_driver+0x6a/0x18c
   [<900dd768>] driver_register+0x60/0xb8
   [<90011594>] __initcall_w1_therm_init6+0x0/0x4
   [<90008e00>] w1_gpio_init+0x0/0x14
   [<9000030c>] kernel_init+0x0/0xe8
   [<900ddf48>] platform_driver_register+0x30/0x38
   [<90011594>] __initcall_w1_therm_init6+0x0/0x4
   [<90008e00>] w1_gpio_init+0x0/0x14
   [<9000030c>] kernel_init+0x0/0xe8
   [<900ddf5e>] platform_driver_probe+0xe/0x3c
   [<90008e0c>] w1_gpio_init+0xc/0x14
   [<90011594>] __initcall_w1_therm_init6+0x0/0x4
   [<90008e00>] w1_gpio_init+0x0/0x14
   [<900126d4>] do_one_initcall+0x34/0x130
   [<90000372>] kernel_init+0x66/0xe8
   [<90011594>] __initcall_w1_therm_init6+0x0/0x4
   [<9001ca3e>] do_exit+0x0/0x3a6
   [<9000030c>] kernel_init+0x0/0xe8
   [<9001ca3e>] do_exit+0x0/0x3a6

  ---[ end trace 5a9233884fead918 ]---
  kobject_add_internal failed for w1 bus master with -EEXIST, don't try to register things with the same name in the same directory.
Signed-off-by: NFlorian Faber <faber@faberman.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes the deadlock when inserting and removing the ds2780.
Signed-off-by: NClifton Barnes <cabarnes@indesign-llc.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Adds a nolock function to the w1 interface to avoid locking the
mutex if needed.
Signed-off-by: NClifton Barnes <cabarnes@indesign-llc.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Simply creates one point to call the w1 interface.
Signed-off-by: NClifton Barnes <cabarnes@indesign-llc.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Straightforward.  As an aside, the ida_init calls are not needed as far as
I can see needed.  (DEFINE_IDA does the same already).
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: NClifton Barnes <cabarnes@indesign-llc.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add "depends on GENERIC_HARDIRQS" to avoid compile breakage on s390:

drivers/built-in.o: In function `pps_gpio_remove':
linux-next/drivers/pps/clients/pps-gpio.c:189: undefined reference to `free_irq'
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: James Nuss <jamesnuss@nanometrics.ca>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This client driver allows you to use a GPIO pin as a source for PPS
signals.  Platform data [1] are used to specify the GPIO pin number,
label, assert event edge type, and whether clear events are captured.

This driver is based on the work by Ricardo Martins who submitted an
initial implementation [2] of a PPS IRQ client driver to the linuxpps
mailing-list on Dec 3 2010.

[1] include/linux/pps-gpio.h
[2] http://ml.enneenne.com/pipermail/linuxpps/2010-December/004155.html

[akpm@linux-foundation.org: remove unneeded cast of void*]
Signed-off-by: NJames Nuss <jamesnuss@nanometrics.ca>
Cc: Ricardo Martins <rasm@fe.up.pt>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Signed-off-by: NRicardo Martins <rasm@fe.up.pt>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A default echo function has been provided so it is no longer an error when
you specify PPS_ECHOASSERT or PPS_ECHOCLEAR without an explicit echo
function.  This allows some code re-use and also makes it easier to write
client drivers since the default echo function does not normally need to
change.
Signed-off-by: NJames Nuss <jamesnuss@nanometrics.ca>
Reviewed-by: NBen Gardiner <bengardiner@nanometrics.ca>
Acked-by: NRodolfo Giometti <giometti@linux.it>
Cc: Ricardo Martins <rasm@fe.up.pt>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Modify Ethernet addess macros to be compatible with BE/LE platforms
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Chul Kim <chul.kim@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: <stable@kernel.org>		[2.6.39+]
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The "goto cleanup" path can deference "rswitch" when it is NULL.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Chul Kim <chul.kim@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add RapidIO mport driver for IDT TSI721 PCI Express-to-SRIO bridge device.
 The driver provides full set of callback functions defined for mport
devices in RapidIO subsystem.  It also is compatible with current version
of RIONET driver (Ethernet over RapidIO messaging services).

This patch is applicable to kernel versions starting from 2.6.39.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NChul Kim <chul.kim@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The discovered bit in PGCCSR register indicates if the device has been
discovered by system host.  In Rapidio systems, some agent devices can also
be master devices.  They can issue requests into the system.
Signed-off-by: NLiu Gang <Gang.Liu@freescale.com>
Acked-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The driver is added using platform_driver_probe(), so the callbacks can be
discarded more aggessively.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add initial support for the microchip mcp7941x series of real time clocks.

The mcp7941x series is generally compatible with the ds1307 and ds1337 rtc
devices from dallas semiconductor.  minor differences include a backup
battery enable bit, and the polarity of the oscillator enable bit.
Signed-off-by: NDavid Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>