Swapping a cable from a "Mgmt Allowed=No" switch port to a
"Mgmt Allowed=Yes" switch port doesn't send a pkey change
notification. Therefore, the link doesn't become active as
the oib_utils layer uses an old pkey table cache.

Fix by ensuring the pkey change notification is sent when
the table is changed both explicitly by the FM and implicitly
by the driver via a cable swap.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When FM is disabled, and the HFI port on the switch is
changed from MgmtAllowed=YES to MgmtAllowed=NO and the
link is bounced, FULL_MGMT_P_KEY doesn't get cleared
from the pkey table. This also occurs when the QSFP
cable is moved from a switch port with MgmtAllowed=YES
to a MgmtAllowed=NO port. Clear pkey entry properly.

Also, when the driver is loaded and the switch port is
set to MgmtAllowed=NO, FULL_MGMT_P_KEY shouldn't be added
to pkey table after FM is started. Only set FULL_MGMT_P_KEY
in the pkey table if switch port is configured to
MgmtAllowed=YES.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The TODO list for the hfi1 driver was completed during 4.6. In addition
other objections raised (which are far beyond what was in the TODO list)
have been addressed as well. It is now time to remove the driver from
staging and into the drivers/infiniband sub-tree.
Reviewed-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The handling of the congestion setting MAD packet only
saved off the values, waiting for a congestion control
table packet before going active.  Instead, immediately
apply the values.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

A MAD directive to start polling must go through the normal
link tuning and start steps in order to correctly handle
active cables.
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDean Luick <dean.luick@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The current LED beaconing code is unclear and uses the timer handler to
turn off the timer. This patch simplifies the code by removing the
special semantics of timeon = timeoff = 0 being interpreted as a request
to turn off the beaconing.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Removed parantheses on the right hand side of assignments as they are not
needed. Coccinelle patch used:

@@ expression a, b; @@

a = &
-(
b
-)
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Casting a pointer to a pointer of the same type is unnecessary, so
remove these unnecessary casts.

This was done with Coccinelle:

@@
type T;
T *ptr;
@@
- (T *)ptr
+ ptr
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The LedInfo SMA attribute is redefined to control the LED beaconing
state machine instead of the LED directly. In accordance, we now
return the state of LED beaconing, represented by whether the beaconing
timer is active, instead of the state of the LED itself for SMA queries
Get(LedInfo) and Get(PortInfo). While we are at it, we fix the beaconing
timer control code so that the state of the timer is accurately updated.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Fix the header by moving the copyright notice out of the license text
and to the top of the header. Also, update the copyright date.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add braces on all arms of statements to fix checkpatch check:
CHECK: braces {} should be used on all arms of this statement
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Fix code alignment to fix checkpatch check:
CHECK: Alignment should match open parenthesis
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Fix block comments with proper formatting to fix checkpatch warnings:
WARNING: Block comments use * on subsequent lines
WARNING: Block comments use a trailing */ on a separate line
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Split multiple assignments into individual assignments to fix
checkpatch check:
CHECK: multiple assignments should be avoided
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove unnecessary parentheses around addressof single $Lvals to fix
checkpatch check:
CHECK: Unnecessary parentheses around $var
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Move logical continuations to previous line to fix checkpatch check:
CHECK: Logical continuations should be on the previous line
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove extra blank line before close brace to fix checkpatch check:
CHECK: Blank lines aren't necessary before a close brace '}'
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove blank line after an open brace to fix checkpatch check:
CHECK: Blank lines aren't necessary after an open brace '{'
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Convert pointer comparisons to NULL to !pointer
to fix checkpatch check:
CHECK: Comparison to NULL could be written "!pointer"
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove the space after a cast to fix checkpatch check:
CHECK: No space is necessary after a cast
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove multiple blank lines to fix checkpatch check:
CHECK: Please don't use multiple blank lines
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Add spaces around binary operators.

Fixes checkpatch check:
CHECK: spaces preferred around that 'x'
where x is a binary operator
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

If an SL->SC mapping table change occurs after an RC/UC QP is created,
there is no mechanism to change the SC nor the VL for that QP. The fix
is to place the QP into error state so that ULP can recreate the QP with
the new SL->SC mapping.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NKaike Wan <kaike.wan@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

It enables access to counters in
/sys/class/infiniband/hfi1_0/ports/1/counters
by providing infrastructure when PMA queries occur. Counters symbol_error
and VL15_dropped are not supported in OPA, therefore, 0 will always be
returned. In addition, two common routines (pma_get_opa_port_dctrs,
pma_get_opa_port_ectrs) were created to query counters to avoid code
duplication.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

It replaces goto's for break and return statements in process_perf_opa().
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This commit changes the data type for port_num in
pma_get_opa_porterrors() from unsigned long to u8.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NSebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Delete code from query_port which has been moved into rvt_query_port
Create a call back function to shut down a port which may be called from
rvt_modify_port
Signed-off-by: NHarish Chegondi <harish.chegondi@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch implements LED beaconing for maintenance. A MAD packet with
the LEDInfo attribute set to 1 will enable LED beaconing with a duty
cycle of 2s on and 1.5s off. A MAD packet with the LEDInfo attribute
set to 0 will disable beaconing and return the LED to normal operation.
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NMitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The current code employs a heuristic to guess the port type.
The canonical location to identify the port type of the
designed platform is from the platform configuration data.

This patch uses the previously fetched port type from the platform
configuration and removes the now obsolete heuristic routine
and its associated defines.
Reviewed-by: NArthur Kepner <arthur.kepner@intel.com>
Signed-off-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Removing QSFP cable should report 'No Local Media' instead of
'Transient' as reported by 'opaportinfo'.
Workaround is to change the state to
OPA_LINKDOWN_REASON_LOCAL_MEDIA_NOT_INSTALLED in cable handler.

With cable still removed, 'opaportinfo bounce' should not cause a
state change to Polling, as reported by 'opaportinfo'.
Resolution is to prevent physical state change from Offline->Polling.

Use a macro to mask lower nibble of OPA_LINKDOWN_REASON* as needed
for offline_disabled_reason.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NEaswar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reported-by: NTodd Rimmer <todd.rimmer@intel.com>
Signed-off-by: NBryan Morgan <bryan.c.morgan@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Get rid of create and free mad agent from the driver and use rdmavt
version.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Remove most of the ibport members from hfi1 and use the rdmavt version.
Also register the port with rdmavt.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: NHarish Chegondi <harish.chegondi@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Original patch from Kamal Heib <kamalh@mellanox.com>, split
apart from original and modified to accomodate recent changes
in rdmavt.

Remove AH from hfi1 and use rdmavt version.
Signed-off-by: NKamal Heib <kamalh@mellanox.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Rdmavt split the header files to be based on ibta object. This patch
makes changes in hfi1 to account for the move.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch begins to make use of rdmavt by registering with it and
providing access to the header files. This is just the beginning of
rdmavt support in hfi1.
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Total XMIT wait needs to sum the xmit wait values of all the VLs not just
those requested in the query.  Also, make the algorithm used for both
PortStatus and PortDataCounters the same.
Reviewed-by: NArthur Kepner <arthur.kepner@intel.com>
Reviewed-by: NBreyer, Scott J <scott.j.breyer@intel.com>
Signed-off-by: NIra Weiny <iweiny@gmail.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This patch fixes the checkpatch issue:
CHECK: Prefer using the BIT macro

Use of BIT macro for HDRQ_INCREMENT in chip.h causes a change in
format specifier for error message in init.c in order to avoid a
build warning.
Reviewed-by: NDean Luick <dean.luick@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Total XMIT wait needs to sum the xmit wait values of all the VLs not just
those requested in the query.  Also, make the algorithm used for both
PortStatus and PortDataCounters the same.
Reviewed-by: NArthur Kepner <arthur.kepner@intel.com>
Reviewed-by: NBreyer, Scott J <scott.j.breyer@intel.com>
Signed-off-by: NIra Weiny <iweiny@gmail.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

send_trap() was still using old ib_smp instead of opa_smp
for formatting and sending traps.
Reviewed-by: NArthur Kepner <arthur.kepner@intel.com>
Reviewed-by: NIra Weiny <ira.weiny@intel.com>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NErik E. Kahn <erik.kahn@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Changing the 32-bit reserved field in opa_port_data_counters_msg
to the new 'resolution' field. PMA will use resolutions to right-
shift values for LocalLinkIntegrity and LinkErrorRecovery when
computing the ErrorCounterSummary for a DataPortCounters request.
Reviewed-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: NAndrea Lowe <andrea.l.lowe@intel.com>
Signed-off-by: NJubin John <jubin.john@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>