There is no need to configure the enabled ports once in b53_setup() and then a
second time around when dsa_switch_ops::port_enable is called, just do it when
port_enable is called which is better in terms of power consumption and
correctness.
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for future changes allowing the configuring of multiple
CPU ports, make b53_enable_cpu_port() take a port argument.
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is not used anywhere, so remove it.
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add three new traps needed for multicast routing:
 - PIM: Trap for PIM protocol control packets.
 - RPF: Trap for packets that fail the RPF check on a specific hardware
   route entry.
 - MULTICAST: Generic trap for multicast. It is used for routes that trap
   the packets to the CPU.

The RPF and MULTICAST traps have rate limiters as these traps may have
line-rate of packets trapped. The PIM trap has a rate limiter similarly to
other L3 control protocols. The rate limiters are implemented by adding
three new trap groups for the newly introduced traps.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlxsw_sp_rif struct, defined as private struct in spectrum_router.c
will be used in the multicast router source file. Due to the fact that the
dev field will be needed by the multicast router logic, add an access
function to it.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turn on two bits on the Spectrum RIF configuration:
 - IPv4 multicast: when a multicast packet arrives on a RIF, send it to go
   through multicast routes lookup.
 - IPv4 multicast forwarding enable: when multicast packet arrives on a
   RIF, allow it to be forwarded by multicast routes. If this bit is not
   set, multicast packets will go through multicast routing lookup but will
   be dropped at the egress of the ports.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RRCR register is used for copying and moving TCAM multicast routes
from different offsets. It will be used to allow routes relocation for
parman ops as part of the multicast router offloading logic.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RMFT-V2 register is used to configure and query the multicast table and
will be used by the multicast router offloading logic.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The multicast ERIF list entries resource indicates the number of entries
that can be put in one rigr2 register operation. While the register can
hold up to MLXSW_REG_RIGR2_MAX_ERIFS ( = 32) ERIF entries, the actual
number allowed by firmware is indicated with this resource.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RIGR-V2 register is used to add, remove and query egress interface list
of a multicast forwarding entry and it will be used by the multicast
router offloading logic.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This register is used for allocation of regions in the TCAM table and it
will be used by the multicast router offloading logic.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MLXSW_REG_PXXX_FLEX_ACTION_SET_LEN is relevant for the multicast router
registers too, so rename it to have a general name which is not bound to a
specific register.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the trap ACL action to be configured with different traps. This
allows the multicast router offloading code to use that same ACL action
with the multicast router traps. By using different traps, the multicast
router can have different trap policies and can handle the packet
differently.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Spectrum multicast forwarding is done using an ACL action. Add the
mcrouter ACL action that will be used to offload the multicast router
logic.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A flexible action instance allows, given a set of ops, creating, committing
and sharing a set of ACL action blocks. The flexible action instance in
question is using the spectrum KVD linear space to store the flexible
action sets.

Move this flexible action instance to the common spectrum struct to allow
other users (such as multicast router) to get that functionality.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The multicast router offloading code is going to require the counter_pools
initialization to occur before the router initialization, thus, change the
spectrum initialization order to fix it.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove a goto in the PPv2 tx function which jumps to the next line
anyway. This is a cosmetic commit.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Performance gain when receiving locally is 55->95Mbps and 50->65Mbps for NAT.
Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When such interrupts occur there is not much we can do.
Dropping the whole ring doesn't help and only produces high packet loss.
If we just ignore the interrupt the mac will drop one or few packets instead of the whole ring.
Also this will lower the irq handling load and increase performance.
Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify baycom driver to use the new parallel port device model.
Signed-off-by: NSudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-By: NThomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

uf_info.regs is resource_size_t i.e. phys_addr_t that can be either u32
or u64 according to CONFIG_PHYS_ADDR_T_64BIT.

The printk format is thus adaptet to u64 and the regs value cast to u64
to take both u32 and u64 into account.
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_map_single functions are obsolete. So replace them with
dma_map_single functions.
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add RTL8201F phy-id and the related functions to the driver.

The original patch is as follows:
https://patchwork.kernel.org/patch/2538341/Signed-off-by: NJongsung Kim <neidhard.kim@lge.com>
Signed-off-by: NJassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This renames the definition of page select register from
RTL8211F_PAGE_SELECT to RTL821x_PAGE_SELECT to use it across models.
Signed-off-by: NKunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dummy device name is enumerated by the kernel, let user space be aware
of the naming scheme used by dummy devices:
(visible in /sys/class/net/<iface>/name_assign_type).
Signed-off-by: NZhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.

This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.

Fixes: 65e65ec1 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NAndreas Rammhold <andreas@rammhold.de>
Reported-by: NFlorian Klink <flokli@flokli.de>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default receive buffer size was reduced by recent change
to a value which was appropriate for 10G and Windows Server 2016.
But the value is too small for full performance with 40G on Azure.
Increase the default back to maximum supported by host.

Fixes: 8b532797 ("netvsc: allow controlling send/recv buffer size")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the network interface is kept running during suspend, the net core
may call net_device_ops.ndo_start_xmit() while the Ethernet device is
still suspended, which may lead to a system crash.

E.g. on sh73a0/kzm9g and r8a73a4/ape6evm, the external Ethernet chip is
driven by a PM controlled clock.  If the Ethernet registers are accessed
while the clock is not running, the system will crash with an imprecise
external abort.

As this is a race condition with a small time window, it is not so easy
to trigger at will.  Using pm_test may increase your chances:

    # echo 0 > /sys/module/printk/parameters/console_suspend
    # echo platform > /sys/power/pm_test
    # echo mem > /sys/power/state

To fix this, make sure the network interface is quietened during
suspend.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can enter a deadlock situation because there is no sufficient protection
when ndo_get_stats64() runs in process context to guard against RX or TX NAPI
contexts running in softirq, this can lead to the following lockdep splat and
actual deadlock was experienced as well with an iperf session in the background
and a while loop doing ifconfig + ethtool.

[    5.780350] ================================
[    5.784679] WARNING: inconsistent lock state
[    5.789011] 4.13.0-rc7-02179-g32fae27c725d #70 Not tainted
[    5.794561] --------------------------------
[    5.798890] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[    5.804971] swapper/0/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
[    5.810175]  (&syncp->seq#2){+.?...}, at: [<c0768a28>] bcm_sysport_tx_reclaim+0x30/0x54
[    5.818327] {SOFTIRQ-ON-W} state was registered at:
[    5.823278]   bcm_sysport_get_stats64+0x17c/0x258
[    5.828053]   dev_get_stats+0x38/0xac
[    5.831776]   rtnl_fill_stats+0x30/0x118
[    5.835761]   rtnl_fill_ifinfo+0x538/0xe24
[    5.839921]   rtmsg_ifinfo_build_skb+0x6c/0xd8
[    5.844430]   rtmsg_ifinfo_event.part.5+0x14/0x44
[    5.849201]   rtmsg_ifinfo+0x20/0x28
[    5.852837]   register_netdevice+0x628/0x6b8
[    5.857171]   register_netdev+0x14/0x24
[    5.861051]   bcm_sysport_probe+0x30c/0x438
[    5.865280]   platform_drv_probe+0x50/0xb0
[    5.869418]   driver_probe_device+0x2e8/0x450
[    5.873817]   __driver_attach+0x104/0x120
[    5.877871]   bus_for_each_dev+0x7c/0xc0
[    5.881834]   bus_add_driver+0x1b0/0x270
[    5.885797]   driver_register+0x78/0xf4
[    5.889675]   do_one_initcall+0x54/0x190
[    5.893646]   kernel_init_freeable+0x144/0x1d0
[    5.898135]   kernel_init+0x8/0x110
[    5.901665]   ret_from_fork+0x14/0x2c
[    5.905363] irq event stamp: 24263
[    5.908804] hardirqs last  enabled at (24262): [<c08eecf0>] net_rx_action+0xc4/0x4e4
[    5.916624] hardirqs last disabled at (24263): [<c0a7da00>] _raw_spin_lock_irqsave+0x1c/0x98
[    5.925143] softirqs last  enabled at (24258): [<c022a7fc>] irq_enter+0x84/0x98
[    5.932524] softirqs last disabled at (24259): [<c022a918>] irq_exit+0x108/0x16c
[    5.939985]
[    5.939985] other info that might help us debug this:
[    5.946576]  Possible unsafe locking scenario:
[    5.946576]
[    5.952556]        CPU0
[    5.955031]        ----
[    5.957506]   lock(&syncp->seq#2);
[    5.960955]   <Interrupt>
[    5.963604]     lock(&syncp->seq#2);
[    5.967227]
[    5.967227]  *** DEADLOCK ***
[    5.967227]
[    5.973222] 1 lock held by swapper/0/0:
[    5.977092]  #0:  (&(&ring->lock)->rlock){..-...}, at: [<c0768a18>] bcm_sysport_tx_reclaim+0x20/0x54

So just remove the u64_stats_update_begin()/end() pair in ndo_get_stats64()
since it does not appear to be useful for anything. No inconsistency was
observed with either ifconfig or ethtool, global TX counts equal the sum of
per-queue TX counts on a 32-bit architecture.

Fixes: 10377ba7 ("net: systemport: Support 64bit statistics")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When building an allmodconfig kernel with gcc-4.6, we get a rather
odd warning:

drivers/net/vrf.c: In function ‘vrf_ip6_input_dst’:
drivers/net/vrf.c:964:3: error: initialized field with side-effects overwritten [-Werror]
drivers/net/vrf.c:964:3: error: (near initialization for ‘fl6’) [-Werror]

I have no idea what this warning is even trying to say, but it does
seem like a false positive. Reordering the initialization in to match
the structure definition gets rid of the warning, and might also avoid
whatever gcc thinks is wrong here.

Fixes: 9ff74384 ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.

Semantic patch used to resolve this issue:

@@
expression e,e2; constant c;
statement S;
@@

  e = kzalloc(e2, c);
  if(e == NULL) S
- memset(e, 0, e2);
Signed-off-by: NHimanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: NHimanshu Jha <himanshujha199640@gmail.com>
Acked-by: NSudarsana Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tnapi is being initialized and then immediately updated and
hence the initialiation is redundant.  Clean up the warning
by moving the declaration and initialization to the inside
of the for-loop.

Cleans up clang scan-build warning:
warning: Value stored to 'tnapi' during its initialization is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

... and __initconst if applicable.

Based on similar work for an older kernel in the Grsecurity patch.

[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJean Delvare <jdelvare@suse.de>

The control process (NSP) may take some time to complete its
initialization.  This is not a problem on most servers, but
on very fast-booting machines it may not be ready for operation
when driver probes the device.  There is also a version of the
flash in the wild where NSP tries to train the links as part
of init.  To wait for NSP initialization we should make sure
its resource has already been added to the resource table.
NSP adds itself there as last step of init.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Board state informs us which low-level initialization stages the card
has completed.  We should wait for the card to be fully initialized
before trying to communicate with it, not only before we configure
passing traffic.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>