The gpio-pch driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit 4df42de9d3e "gpio: omap: add a GPIO_OMAP option instead of using
ARCH_OMAP" made it possible to build OMAP kernels without the GPIO driver,
which at least on OMAP2 and OMAP3 causes build errors because of functions
used by the platform power management code:

arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm24xx.c:129: undefined reference to `omap2_gpio_prepare_for_idle'
arch/arm/mach-omap2/pm24xx.c:129: undefined reference to `omap2_gpio_resume_after_idle'

We presumably always want the GPIO driver on OMAP, so this adds a slightly
broader dependency and only allows disabling the driver only when no
OMAP2PLUS platform is selected.

However, it seems entirely reasonable to include the driver in build tests
on other platforms, so we should also allow building it for COMPILE_TEST
builds and select the required GENERIC_IRQ_CHIP that may not already be
enabled on other platforms.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Converts the GPIO OMAP driver to register its chained irq
handler and irqchip using the helpers in the gpiolib core.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ARCH_OMAP config option was used to built the GPIO OMAP
driver but this is not consistent with the rest of the GPIO
drivers that have their own Kconfig option.

Also, this make it harder to add dependencies or reverse
dependencies (i.e: select) since that would mean touching the
sub-arch config option.

So is better to add a boolean Kconfig option for this driver
that defaults to true if ARCH_OMAP is enabled.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

GPIO_TIMBERDALE doesn't need an explicit dependency on HAS_IOMEM,
because it depends on MFD_TIMBERDALE which itself depends on
HAS_IOMEM already.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Now that the gpiolib irqchip helpers can support nested, threaded
IRQ handlers, switch the TC3589x driver over to using this new
infrastructure. Tested on the Ux500.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This converts the PL061 driver to register its chained irq
handler and irqchip using the helpers in the gpiolib core.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This provides a function gpiochip_irqchip_add() to set
up an irqchip for a GPIO controller, and a function
gpiochip_set_chained_irqchip() to chain it to a parent
irqchip.

Most GPIOs are of the type where a number of lines form
a cascaded interrupt controller chained onto
the primary system interrupt controller (or further down the
chain) so let's add this helper and factor the code to
request the lines to be used as IRQs, the .to_irq() function
and the irqdomain into the core as well.
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

SYSCON driver was designed for using memory areas (registers)
that are used in several subsystems. There are systems (CPUs)
which use bits in one register for various purposes and thus
should be handled by various kernel subsystems. This driver
allows you to use the individual SYSCON bits as GPIOs.
ARM CLPS711X SYSFLG1 input lines has been added as first user
of this driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@linux-m68k.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The bus and architecture dependencies are already on MFD_CS5535, so
there is no need to repeat them here.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

fix build error with this message:
kernel/irq/Kconfig:41:error: recursive dependency detected!
kernel/irq/Kconfig:41:  symbol GENERIC_IRQ_CHIP is selected by GPIO_DWAPB
drivers/gpio/Kconfig:131:       symbol GPIO_DWAPB depends on IRQ_DOMAIN
kernel/irq/Kconfig:46:  symbol IRQ_DOMAIN is selected by GENERIC_IRQ_CHIP
Signed-off-by: NAlan Tull <atull@altera.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Instead of just depending on OF and getting build failures,
depend on ARM && OF_GPIO.

Cc: Fabian Vogt <fabian@ritter-vogt.de>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The Synopsys DesignWare block is used in some ARM devices (picoxcell)
and can be configured to provide multiple banks of GPIO pins.

v12: - Add irq_startup/shutdown
     - do irq_create_mapping() in probe, irq_find_mapping() in to_irq()
     - Adjust mappings to show support for 1 gpio per port.
     - gpio-cells = <1>
v11: - Use NULL when checking existence of 'interrupts' property
     - Bindings descriptions cleanup
v10: - in documentation nr-gpio -> nr-gpios
v9:  - cleanup in dt bindings doc
     - use of_get_child_count()
v8:  - remove socfpga.dtsi changes
     - minor cleanup in devicetree documentation
v7:  - use irq_generic_chip
     - support one irq per gpio line or one irq for many
     - s/bank/port/ and other cleanup
v6:  - (atull) squash the set of patches
     - use linear irq domain
     - build fixes. Original driver was reviewed on v3.2.
     - Fix setting irq edge type for 'rising' and 'both'.
     - Support as a loadable module.
     - Use bgpio_chip's spinlock during register access.
     - Clean up register names to match spec
     - s/bank/port/ because register names use the word 'port'
     - s/nr-gpio/nr-gpios/
     - don't get/put the of_node
     - remove signoffs/acked-by's because of changes
     - other cleanup
v5:  - handle sparse bank population correctly
v3:  - depend on rather than select IRQ_DOMAIN
     - split IRQ support into a separate patch
v2:  - use Rob Herring's irqdomain in generic irq chip patches
     - use reg property to indicate bank index
     - support irqs on both edges based on LinusW's u300 driver
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NAlan Tull <atull@altera.com>
Reviewed-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This driver supports the GPIO controller found in LSI ZEVIO SoCs.
It has been successfully tested on a TI nspire CX calculator.
Signed-off-by: NFabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There is no point in displaying the TS5500-specific driver entries if
TS5500 board support itself isn't enabled.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NAlexandre Courbot <gnurou@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We've split Qualcomm MSM support into legacy and multiplatform.  The gpio
msm-v2 driver is only relevant on the multiplatform supported SoCs so
switch the Kconfig depends to ARCH_QCOM.

CC: Linus Walleij <linus.walleij@linaro.org>
Acked-by: NAlexandre Courbot <gnurou@gmail.com>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Add Exar XRA1202 8-bit GPIO expander to supported list.
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Acked-by: NGraeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add the NXP PCA9698 40-bit GPIO expander to the supported list.
Note: This only enables GPIO functionality.
Tested-by: NBob Schmitz <bschmitz@xes-inc.com>
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Acked-by: NGraeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The pca953x driver supports tca6424 (24-bit) and pca9505 (40-bit)
devices. They were the only supported devices not mentioned in the
Kconfig help.
Signed-off-by: NAaron Sierra <asierra@xes-inc.com>
Acked-by: NGraeme Smecher <gsmecher@threespeedlogic.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

commit f1f70479 "gpio: pl061: support irqdomain" drops the support of
irq generic chip and use irqdomain instead. Thus fixes the dependency by
selecting IRQ_DOMAIN rather than GENERIC_IRQ_CHIP.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

gpio-tb10x driver uses generic irq chip APIs (irq_alloc_domain_generic_chips,
irq_remove_generic_chip), so it needs to select GENERIC_IRQ_CHIP to avoid build
error.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This is one of LP3943 MFD driver.
LP3943 is configurable as a GPIO expander, up to 16 GPIOs.

* Application note: how to configure LP3943 as a GPIO expander
  http://www.ti.com/lit/an/snva287a/snva287a.pdf

* Supported GPIO controller operations
  request, free, direction_input, direction_output, get and set

* GPIO direction register not supported
  LP3943 doesn't have the GPIO direction register. It only provides input and
  output status registers.
  So, private data for the direction should be handled manually.
  This variable is updated whenever the direction is changed and
  used in 'get' operation.

* Pin assignment
  A driver data, 'pin_used' is checked when a GPIO is requested.
  If the GPIO is already assigned, then returns as failure.
  If the GPIO is available, 'pin_used' is set.
  When the GPIO is not used anymore, then it is cleared.
  It is defined as unsigned long type for atomic bit operation APIs,
  but only LSB 16bits are used because LP3943 has 16 outputs.
Signed-off-by: NMilo Kim <milo.kim@ti.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The MCP drivers fails to compile on trial builds due to missing
Kconfig dependency on OF_GPIO. Fix it.

Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds interrupt functionality for i2c chips to the driver.
They can act as a interrupt-controller and generate interrupts, if
the inputs change.
This is tested with a mcp23017 chip on an arm based platform.

v3:
- be a bit more clear that the irq functionality is also available
  on spi versions of the chips, but the linux driver does not support
  this yet

v2:
- some more word about irq-mirror property in binding doc
- use of_read_bool instead of of_find_property for
  "interrupt-contrller" and "irq-mirror"
- cache the "interrupt-controller" for remove function
- do set the irq-mirror bit only if device is marked as
  interrupt-controller
- do create the irq mapping and setup of irq_desc of all possible
  interrupts in probe path instead of in gpio_to_irq
- mark gpios as in use as interrupts in irq in irq_startup and
  unlock it in irq_shutdown
- rename virq to child_irq
- remove dev argument from mcp23s08_irq_setup function
- move gpiochip_add before mcp23s08_irq_setup in probe path
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Prevent build failure when the selected variant does not support GPIO32.
Acked-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This helps increasing build testing coverage.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The compatible to Davinci GPIO HW block is used by other TI SoCs, like
Keystone, where GPIO support is declared as optional.

Hence, introduce GPIO_DAVINCI Kconfig option which will allow to enable
Davinci GPIO driver for Keystone SoCs when needed. At same time, kept
Davinci GPIO driver enabled for Davinci SoCs by default.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This patch adds support for the GPIOs found on the SMSC "Super I/
SCH311x.

The chip detection and I/O functions are copied from sch311x_wdt.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

GPIO32 is a standard optional extension to the Xtensa architecture
core that provides preconfigured output and input ports for intra
SoC signaling. The GPIO32 option is implemented as 32bit Tensilica
Instruction Extension (TIE) output state called EXPSTATE, and 32bit
input wire called IMPWIRE. This driver treats input and output
states as two distinct devices.

v3:
* Use BUG() in xtensa_impwire_set_value() to indicate that
  it should never be called (Linus Walleij)
v2:
* Address the comments of Linus Walleij:
  - Add a few comments
  - Expand commit log message
  - Use the BIT() macro for bit offsets
  - Rewrite CPENABLE handling as static inlines
  - Use device_initcall()
* Depend on !SMP for reason explained in the comments (Marc Gauthier)
* Use XCHAL_CP_ID_XTIOP to enable/disable GPIO32 only
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit 20bc4d5d
(gpio: 74x164: Add support for the daisy-chaining) introduce check
for DT for the driver, so driver cannot be used without DT.
There are no in-tree users of this driver, so remove non-DT support
completely.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add GPIO driver for MOXA ART SoCs.
Signed-off-by: NJonas Jensen <jonas.jensen@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Change CONFIG_GPIO_LYNXPOINT from bool to tristate so that the
gpio-lynxpoint driver can be built as a module.

Add the required glue: an exit function to unregister the driver, and
module information.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The pl061 driver has no real dependency on ARM, so remove the kconfig
dependency.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Current Kconfig allows GPIO_DEVRES to be selected and compiled without
GPIOLIB. This does not make sense anymore since GPIOLIB has become the
exclusive way to deal with GPIOs. This patch makes GPIO_DEVRES available
only if GPIOLIB is selected.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The GPIO driver for the Abilis Systems TB10x series of SOCs based on ARC700
CPUs. It supports GPIO control and GPIO interrupt generation. This driver
works in conjunction with the TB10x pinctrl driver.
Signed-off-by: NSascha Leuenberger <sascha.leuenberger@abilis.com>
Signed-off-by: NChristian Ruppert <christian.ruppert@abilis.com>
Acked-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

gpio-langwell is a deprecated name. Despite the driver was made
initially for Langwell, it supports now other Intel Mid SoC's.

This patch does no change beside the file renaming with Kconfig/Makefile
update.
Signed-off-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Move the IOP GPIO driver to live with its siblings in the
GPIO subsystem.

Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

With the recent code cleanup from Marek Vasut, driver gpio-ucb1400 can
be built as a module, so change symbol GPIO_UCB1400 from bool to
tristate.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Reviewed-by: NMarek Vasut <marex@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add the GPIO driver for the Broadcom bcm281xx family of mobile SoCs.
These GPIO controllers may contain up to 8 banks where each bank
includes 32 pins that can be driven high or low and act as an edge
sensitive interrupt.
Signed-off-by: NMarkus Mayer <markus.mayer@linaro.org>
Reviewed-by: NChristian Daudt <csd@broadcom.com>
Reviewed-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMatt Porter <matt.porter@linaro.org>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
[Added depends on OF_GPIO]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>