Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 17 10月, 2007 1 次提交
  3. 18 7月, 2007 6 次提交
  5. 11 5月, 2007 1 次提交
  7. 10 5月, 2007 1 次提交
  9. 09 5月, 2007 2 次提交
    • J
      au1550 SPI controller driver · 63bd2359
      由 Jan Nikitenko 提交于 
      Here is a driver for the Alchemy au1550 PSC (Programmable Serial
Controller) in SPI master mode.

It supports dma transfers using the Alchemy descriptor based dma controller
for 4-8 bits per word SPI transfers.  For 9-24 bits per word transfers, pio
irq based mode is used to avoid setup of dma channels from scratch on each
number of bits per word change.

Tested with au1550; this may also work on other MIPS Alchemy cpus, like
au1200/au1210/au1250.  Used extensively with SD card connected via SPI;
this handles 8.1MHz SPI clock transfers using dma without any problem (the
highest SPI clock freq possible with au1550 running on 324MHz).

The driver supports sharing of SPI bus by multiple devices.  All features
of Alchemy SPI mode are supported (all SPI modes, msb/lsb first, bits per
word in 4-24 range).

As the SPI clock of the controller depends on main input clock that shall
be configured externally, platform data structure for au1550 SPI controller
driver contains mainclk_hz attribute to define the input clock rate.  From
this value, dividers of the controller for SPI clock are set up for
required frequency.
Signed-off-by: NJan Nikitenko <jan.nikitenko@gmail.com>

Whitespace and section fixups.  Remove partial workaround for platform
setup bug in dma_mask setup; it couldn't work with multiple controllers.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      63bd2359
    • A
      /dev/spidevB.C interface · 814a8d50
      由 Andrea Paterniani 提交于 
      Add a filesystem API for <linux/spi/spi.h> stack.  The initial version of
this interface is purely synchronous.

dbrownell@users.sourceforge.net:

 Cleaned up, bugfixed; much simplified; added preliminary documentation.

 Works with mdev given CONFIG_SYSFS_DEPRECATED; and presumably udev.

 Updated SPI_IOC_MESSAGE ioctl to full spi_message semantics, supporting
 groups of one or more transfers (each of which may be full duplex if
 desired).

 This is marked as EXPERIMENTAL with an explicit disclaimer that the API
 (notably the ioctls) is subject to change.
Signed-off-by: NAndrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      814a8d50
  11. 08 5月, 2007 1 次提交
  13. 15 2月, 2007 1 次提交
  15. 13 2月, 2007 4 次提交
  17. 30 11月, 2006 1 次提交
  19. 22 5月, 2006 3 次提交
  21. 17 5月, 2006 1 次提交
  23. 07 2月, 2006 1 次提交
  25. 14 1月, 2006 4 次提交
    • D
      [PATCH] SPI: add spi_butterfly driver · 2e10c84b
      由 David Brownell 提交于 
      This adds a bitbanging parport based adaptor cable for AVR Butterfly, giving
SPI links to its DataFlash chip and (eventually) firmware running in the card.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      2e10c84b
    • D
      [PATCH] spi: misc fixes · 7111763d
      由 David Brownell 提交于 
      This collects some small SPI patches that seem to be missing from the MM tree:

  - spi_butterfly kbuild hooks got dropped somehow; this restores them
  - quick fix for a (theoretical?) m25p80_write() oops noted by Andrew
  - quick fix for a potential config-specific oops for mtd_dataflash()
  - minor doc tweaks
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      7111763d
    • D
      [PATCH] spi: add spi_bitbang driver · 9904f22a
      由 David Brownell 提交于 
      This adds a bitbanging spi master, hooking up to board/adapter-specific glue
code which knows how to set and read the signals (gpios etc).

This code kicks in after the glue code creates a platform_device with the
right platform_data.  That data includes I/O loops, which will usually
come from expanding an inline function (provided in the header).  One goal
is that the I/O loops should be easily optimized down to a few GPIO register
accesses, in common cases, for speed and minimized overhead.

This understands all the currently defined protocol tweaking options in the
SPI framework, and might eventually serve as as reference implementation.

  - different word sizes (1..32 bits)
  - differing clock rates
  - SPI modes differing by CPOL (affecting chip select and I/O loops)
  - SPI modes differing by CPHA (affecting I/O loops)
  - delays (usecs) after transfers
  - temporarily deselecting chips in mid-transfer

A lot of hardware could work with this framework, though common types of
controller can't reach peak performance without switching to a driver
structure that supports pipelining of transfers (e.g.  DMA queues) and maybe
controllers (e.g.  IRQ driven).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      9904f22a
    • D
      [PATCH] spi: simple SPI framework · 8ae12a0d
      由 David Brownell 提交于 
      This is the core of a small SPI framework, implementing the model of a
queue of messages which complete asynchronously (with thin synchronous
wrappers on top).

  - It's still less than 2KB of ".text" (ARM).  If there's got to be a
    mid-layer for something so simple, that's the right size budget.  :)

  - The guts use board-specific SPI device tables to build the driver
    model tree.  (Hardware probing is rarely an option.)

  - This version of Kconfig includes no drivers.  At this writing there
    are two known master controller drivers (PXA/SSP, OMAP MicroWire)
    and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML
    mentions of other drivers in development.

  - No userspace API.  There are several implementations to compare.
    Implement them like any other driver, and bind them with sysfs.

The changes from last version posted to LKML (on 11-Nov-2005) are minor,
and include:

  - One bugfix (removes a FIXME), with the visible effect of making device
    names be "spiB.C" where B is the bus number and C is the chipselect.

  - The "caller provides DMA mappings" mechanism now has kerneldoc, for
    DMA drivers that want to be fancy.

  - Hey, the framework init can be subsys_init.  Even though board init
    logic fires earlier, at arch_init ... since the framework init is
    for driver support, and the board init support uses static init.

  - Various additional spec/doc clarifications based on discussions
    with other folk.  It adds a brief "thank you" at the end, for folk
    who've helped nudge this framework into existence.

As I've said before, I think that "protocol tweaking" is the main support
that this driver framework will need to evolve.

From: Mark Underwood <basicmark@yahoo.com>

  Update the SPI framework to remove a potential priority inversion case by
  reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      8ae12a0d