We blindly trust the hardware to give us NUL-terminated strings, which
is a bad idea because it doesn't always do that. For example:

  [  481.184784] mpt3sas_cm0: 	enclosure level(0x0000), connector name(     \x3)

In this case, connector_name is four spaces. We got lucky here because
the 2nd byte beyond our character array happens to be a NUL. Fix this by
explicitly writing '\0' to the end of the string to ensure we don't run
off the edge of the world in printk().
Signed-off-by: NCalvin Owens <calvinowens@fb.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The _scsih_pci_mmio_enabled called if scsih_pci_error_detected returns
PCI_ERS_RESULT_CAN_RECOVER, at this point, read/write to the device
still works, no need to reset slot.

Or the mpt3sas_base_map_resources in scsih_pci_slot_reset will fail,
and iounamp ioc->chip, then we will meet issue when read ioc->chip
in mpt3sas_base_get_iocstate from _base_fault_reset_work.

Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In _scsih_sas_host_add, the number of HBA phys are determined and then
later used to allocate an array of struct _sas_phy's.  If the routine
sets ioc->sas_hba.num_phys, but then fails to allocate the
ioc->sas_hba.phy array (by kcalloc error or other intermediate
error/exit path), ioc->sas_hba is left in a dangerous state: all readers
of ioc->sas_hba.phy[] do so by indexing it from 0..ioc->sas_hba.num_phys
without checking that the space was ever allocated.

Modify _scsih_sas_host_add to set ioc->sas_hba.num_phys only after
successfully allocating ioc->sas_hba.phy[].
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There are some missing curly braces on this if statement, so we end up
printing when we shouldn't.

Fixes: a470a51c ('mpt3sas: Handle active cable exception event')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replaced mpt3sas_base_flush_reply_queues() with
mpt3sas_base_sync_reply_irqs(),as mpt3sas_base_flush_reply_queues()
skips over reply queues that are currently busy (i.e. being handled by
interrupt processing in another core). If a reply queue is busy, then
call to synchronize_irq()in mpt3sas_base_sync_reply_irqs()make sures the
other core has finished flushing the queue and completed any calls to
the mid-layer scsi_done() routine.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Set maximum transfer length per IO on RAID volumes to 4MB by setting
VD's queue's max_sector to 8192.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Modified driver code to use scsi_prot_ref_tag() API instead of
scsi_get_lba(), while initializing reference tag field in the CDB.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In-order to handle this 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
driver need to follow below steps,
1. Unmask the 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
so that FW can notify this event to host driver.
2. After receiving this event, add this event to AEN event queue,
for notifying this event to applications.
3. Then Print below message in kernel logs if the event data's reason
code is zero,
"Currently an active cable with ReceptacleID <ID_Value> cannot be powered
and devices connected to this active cable will not be seen. This active
cable requires <PowerValue_in_mW> of power"

This event is only for Intruder/Cutlass HBAs.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Firmware events are queued up using the fw_event_work's struct work, not
its delayed_work member.  The initial driver for SAS2 controllers had
handled firmware reset using the rescan barrier and was later redesigned
through "mpt2sas: [Resend] Host Reset code cleanup".  The delayed_work
variables are now unused and may provoke CONFIG_DEBUG_OBJECTS_TIMERS
"assert_init not available" false warnings in
_scsih_fw_event_cleanup_queue.

Cleanup fw_event_work's unused entries, update its kerneldoc, and
update _scsih_fw_event_cleanup_queue accordingly.

Fixes: 146b16c8 (mpt3sas: Refcount fw_events and fix unsafe list usage)
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Track msix of each IO and use the same msix for issuing abort to timed
out IO. With this driver will process IO's reply first followed by TM.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver assumes HighPriority credit as part of Global credit. But,
Firmware treats HighPriority credit value and global cedits as two
different values. Changed host queue algorithm to treat global credits
and highPriority credits as two different values.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Never block the SEP device (i.e. Never invoke the
scsi_internal_device_block() API for SEP device) even for the delay not
responding events. Blocking the SEP device will create a deadlock while
adding any device to the OS.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1.Wrong size of argument is being passed
 The size of struct being passed as an argument to memset func and area of
 memory being pointed by an instance of struct in memset func should be of
 same structure type.
2.Dereference null return value
3.Array compared against '0'
 Check whether value pointed by particular index of an array is null or not
 in "if" statement.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updated hardware description headers with MPI v2.6 and
mpt3sas_pci_table[] with vendor_ids, device_ids of Cutlass and Intruder
HBA which have support for 4 ports.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag in MPI SCSI IO request
message, check whether TLR is enabled on the drive using
'sas_is_tlr_enabled' API.

Actually in the driver code, driver is using below API's

1. sas_enable_tlr() - to enable the TLR
2. sas_disable_tlr() - to disable the TLR
3. sas_is_tlr_enabled() - to check whether TLR is enabled or not.

but in scsih_qcmd() we have missed to use sas_is_tlr_enabled() API,
instead we checking for TLR bit from flag field of driver's 'struct
MPT3SAS_DEVIC' structure. which is corrected with this patch.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Modified the mpt3sas driver to have a single driver module which
supports both SAS 2.0 & SAS 3.0 HBA devices.

* Added SAS 2.0 HBA device IDs to the mpt3sas_pci_table pci table.

* Created two separate SCSI host templates for SAS2 and SAS3 HBAs so
  that, during the driver load time driver can use corresponding host
  template(based the pci device ID) while registering a scsi host
  adapter instance for that pci device.

* Registered two IOCTL devices, mpt2ctl is for SAS2 HBAs & mpt3ctl for
  SAS3 HBAs. Also updated the code to make sure that mpt2ctl device
  processes only those ioctl cmds issued for the SAS2 HBAs and mpt3ctl
  device processes only those ioctl cmds issued for the SAS3 HBAs.

* Added separate indexing for SAS2 and SAS3 HBAs.

* Replaced compile time check 'MPT2SAS_SCSI' to run time check
  'hba_mpi_version_belonged' whereever needed.

* Aliased this merged driver to mpt2sas using MODULE_ALIAS.

* Moved global varaible 'driver_name' to per adapter instance variable.

* Created two raid function template and used corresponding raid
  function templates based on the run time check
  'hba_mpi_version_belonged'.

* Moved mpt2sas_warpdrive.c file from mpt2sas to mpt3sas folder and
  renamed it as mpt3sas_warpdrive.c.

* Also renamed the functions in mpt3sas_warpdrive.c file to follow
  current driver function name convention.

* Updated the Makefile to build mpt3sas_warpdrive.o file for these
  WarpDrive-specific functions.

* Also in function mpt3sas_setup_direct_io(), used sector_div() API
  instead of division operator (which gives compilation errors on 32 bit
  machines).

* Removed mpt2sas files, mpt2sas directory & mpt3sas_module.c file.

* Added module parameter 'hbas_to_enumerate' which permits using this
  merged driver as a legacy mpt2sas driver or as a legacy mpt3sas
  driver.

  Here are the available options for this module parameter:

   0 - Merged driver which enumerates both SAS 2.0 & SAS 3.0 HBAs
   1 - Acts as legacy mpt2sas driver, which enumerates only SAS 2.0 HBAs
   2 - Acts as legacy mpt3sas driver, which enumerates only SAS 3.0 HBAs

* Removed mpt2sas entries from SCSI's Kconfig and Makefile files.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

setpci reset on nytro warpdrive card along with sysfs access and cli
ioctl access resulted in kernel oops

1. pci_access_mutex lock added to provide synchronization between IOCTL,
   sysfs, PCI resource handling path

2. gioc_lock spinlock to protect list operations over multiple
   controllers

This patch is ported from commit 6229b414 ("mpt2sas: setpci reset
kernel oops fix").
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The fw_event_work struct is concurrently referenced at shutdown. Add a
refcount to protect it and refactor the code to use it.

Additionally, refactor _scsih_fw_event_cleanup_queue() such that it no
longer iterates over the list without holding the lock since
_firmware_event_work() concurrently deletes items from the list.

This patch is ported from commit 008549f6 ("mpt2sas: Refcount
fw_events and fix unsafe list usage"). These changes are also required
for mpt3sas.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

sas_device objects can be referenced concurrently throughout the driver.
We need a way to make sure threads can't delete them out from under each
other. This patch adds the refcount and refactors the code to use it.

Additionally, we cannot iterate over the sas_device_list without holding
the lock or we risk corrupting random memory if items are added or
deleted as we iterate. This patch refactors _scsih_probe_sas() to use
the sas_device_list in a safe way.

This patch is ported from the following mpt2sas driver commit
d224fe0d ("mpt2sas: Refcount sas_device objects and fix unsafe list
usage").
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Ported the following list of WarpDrive-specific patches:

1. commit 0bdccdb0 ("mpt2sas: WarpDrive
   New product SSS6200 support added")

2. commit 82a45258 ("mpt2sas: WarpDrive
   Infinite command retries due to wrong scsi command entry in MPI
   message")

3. commit ba96bd0b ("mpt2sas: Support
   for greater than 2TB capacity WarpDrive")

4. commit 4da7af94 ("mpt2sas: Do not
   retry a timed out direct IO for Warpdrive")

5. commit daeaa9df ("mpt2sas: Avoid type
   casting for direct I/O commands").

Also set the mpt2_ioctl_iocinfo adapter_type to:

1. MPT3_IOCTL_INTERFACE_SAS3 for Gen3 HBAs

2. MPT2_IOCTL_INTERFACE_SAS2_SSS6200 for Warp Drive

3. MPT2_IOCTL_INTERFACE_SAS2  for other Gen2 HBAs
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1. Do not enable MSI-X vectors for SAS2008 B0 controllers

2. Enable a single MSI-X vector for the following controller:

   a. SAS2004
   b. SAS2008
   c. SAS2008_1
   d. SAS2008_2
   e. SAS2008_3
   f. SAS2116_1
   g. SAS2116_2

3. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
   for Gen3 Invader/Fury C0 and above revision HBAs

4. Enable Combined Reply Post Queue Support (i.e. 96 MSI-X vectors)
   for all Intruder and Cutlass HBAs
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Avoid sending PHYDISK_HIDDEN RAID action requests to SAS2 controllers
since they don't support it.

Also enable fast_path only for SAS3 HBAs.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently there is a logging level option provided for each of our
drivers in the kernel configuration utility. Users can enable this
option to get more verbose information. By default it is enabled.

Only when this option is enabled will the functions which display the
required information get compiled in.

As we are merging the both drivers we can no longer provide this
configuration option. Remove the SCSI_MPTXSAS_LOGGING entry from Kconfig
and unconditionally enable logging (by removing the #ifdef
CONFIG_SCSI_MPT3SAS_LOGGING preprocessor check conditions) so that all
functions which are defined to display more verbose information get
compiled in.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1. Use 'hba_mpi_version_belonged' IOC varable to uniquely identify each
individual generation driver functionality at runtime.

2. Declare global variable 'driver_name' and use this variable while
reserving PCI regions and while allocating the IRQs.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Created a mpt3sas_module.c file for mpt3sas driver where it can register
SAS3 HBA devices with PCI, SML, IOCTL subsystems. Also removed the
corresponding interfaces from mpt3sas_scsih.c file.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1. Added mpt2sas driver related macros in mpt3sas header files

2. Made scsi host's, raid class', pci's, ioctl's callback functions
global so that both drivers can use them.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Issue: When the disks are getting discovered and assigned device
handles by the kernel, a device block followed by an unblock
(due to broadcast primitives) issued by the driver is
interspersed by the kernel changing the state of the device.
Therefore the unblock by the driver results in a no operation
within the kernel API.

To fix this one, the below patch checks the return of the unblock API
and performs a block followed by an unblock to unfreeze the block
layer's I/O queue. Sufficient checks and prints are also added in the
driver to identify this condition caused by the kernel.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Created a thread using alloc_ordered_workqueue() API in order to process
the works from firmware Work-queue sequentially instead of
create_singlethread_workqueue() API.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJoe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

For any SCSI command, if the driver receives
IOC status = SCSI_IOC_TERMINATED and log info = 0x32010081 then
that command will be completed with DID_RESET host status.

The definition of this log info value is
"Virtual IO has failed and has to be retried".

Firmware will provide this log info value with IOC Status
"SCSI_IOC_TERMINATED", whenever a drive (with is a part of a volume)
is pulled and pushed back within some minimal delay.
With this log info value, firmware informs the driver to retry the
failed IO command infinite times, so to provide some time for the
firmware to discover the reinserted drive successfully instated of
just retrying failed command for five times(doesn't giving enough
time for firmware to complete the drive discovery) and failing the
IO permanently even though drive came back successfully.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

This Patch will provide more details of the devices such as slot number,
enclosure logical id, enclosure level & connector name in the following
scenarios,

- When end device is added in the topology,

- When the end device is removed from the setup,

- When the SCSI mid layer issues TASK ABORT/ DEVICE RESET/ TARGET RESET during
  error handling,

- When any command to the device fails with Sense key Hardware error or Medium
  error or Unit Attention,

- When firmware returns device error or device not ready status for the end
  device,

- When a Predicted fault is detected on an end device.

This information can be used by the user to identify the location of the
desired drive in the topology.

Driver will get these information by reading the sas device page0.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

During hot-plugging of a disk(having a flaky link), the disk addition
stops and any further disk addition or removal doesn't happen on that
controller.

This is because, when driver receives DELAY_NOT_RESPONDING event for a disk
while it is undergoing addition at the SCSI Transport layer, the driver
would block the I/O to that disk resulting in a deadlock. i.e the disk
addition work couldn't be completed at the SCSI Transport Layer as it
can't send any I/Os (such as Inquiry, Report LUNs etc) to the disk as
I/Os are blocked to this drive. Also any subsequent device removal
(TARGET_NOT_RESPONDING) or link update(RC_PHY_CHANGED) event couldn't be
processed as they are in the queue to get processed after disk addition
event.

Description of Change:
Don't block the drive when drive addition is under the control of SML.
So that SML won't be blocked of issuing the device dicovery commands
(such as Inquiry, Report LUNs etc).
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Copyright, Trademark & Confidentiality legal statements throughout the
source code changed from LSI to Avago.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

mpt2sas, mpt3sas: Fail the host reset initiated due to discovery related I/O timeouts at driver load time

When a flaky disk is there in a topology then during driver load,
discovery related I/O times out; which results in SCSI error recovery
initiating host reset and then the controller won't see any disk.

In this patch, The driver would return FAILED status to the host reset
initiated due to discovery related I/O timeout if ioc->is_driver_loading
is set. This flag would be set until we exit out of scsih_scan_finished().
i.e.
During device discovery if one of the disk is flaky
(which responds to some discovery commands and doesn't respond to some)
the driver wouldn't perform host reset for discovery related I/O timeout.
Instead it would return Failure for the host reset resulting in the
flaky disk getting removed by the SCSI Mid layer,
so other disks would be added correctly.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch will log a message when driver receives "Temperature Threshold
exceeded" event from any temperature sensor.

The message will look similar to like:
mpt3sas0: Temperature Threshold flags a b c d exceeded for Sensor: x !!!
mpt3sas0: Current Temp In Celsius: y

where a b c d are threshold flags 0 1 2 3

Change_set:
1. Get the number of sensor count of this IOC by reading IO Unit page 8 at
   driver initialization time.
2. Also unmask the Temperature Threshold Event at driver initialization
   time
3. Whenever a MPI2_EVENT_TEMP_THRESHOLD event is received from the
   firmware, then print the sensor number, the maximum threshold number it
   has exceed and the current temperature of this sensor.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete.  The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: NHannes Reinecke <hare@suse.de>

Merge two functions, and remove overly verbose debugging output that pokes
into mid-layer internal structures.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>

All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.

Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NVenkatesh Srinivas <venkateshs@google.com>

Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth.  For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.

Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway.  The one other case looks
broken, but I've kept the behavior as-is for now.

Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.

Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove the ordered_tags field, we haven't been issuing ordered tags based
on it since the big barrier rework in 2010.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>