We blindly trust the hardware to give us NUL-terminated strings, which
is a bad idea because it doesn't always do that. For example:

  [  481.184784] mpt3sas_cm0: 	enclosure level(0x0000), connector name(     \x3)

In this case, connector_name is four spaces. We got lucky here because
the 2nd byte beyond our character array happens to be a NUL. Fix this by
explicitly writing '\0' to the end of the string to ensure we don't run
off the edge of the world in printk().
Signed-off-by: NCalvin Owens <calvinowens@fb.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The _scsih_pci_mmio_enabled called if scsih_pci_error_detected returns
PCI_ERS_RESULT_CAN_RECOVER, at this point, read/write to the device
still works, no need to reset slot.

Or the mpt3sas_base_map_resources in scsih_pci_slot_reset will fail,
and iounamp ioc->chip, then we will meet issue when read ioc->chip
in mpt3sas_base_get_iocstate from _base_fault_reset_work.

Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If _scsih_sas_host_add's call to mpt3sas_config_get_sas_iounit_pg0
fails, ioc->sas_hba.parent_dev may be left uninitialized.  A later
device probe could invoke mpt3sas_transport_port_add which will call
sas_port_alloc_num [scsi_transport_sas] with a NULL parent_dev pointer.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In _scsih_sas_host_add, the number of HBA phys are determined and then
later used to allocate an array of struct _sas_phy's.  If the routine
sets ioc->sas_hba.num_phys, but then fails to allocate the
ioc->sas_hba.phy array (by kcalloc error or other intermediate
error/exit path), ioc->sas_hba is left in a dangerous state: all readers
of ioc->sas_hba.phy[] do so by indexing it from 0..ioc->sas_hba.num_phys
without checking that the space was ever allocated.

Modify _scsih_sas_host_add to set ioc->sas_hba.num_phys only after
successfully allocating ioc->sas_hba.phy[].
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There are some missing curly braces on this if statement, so we end up
printing when we shouldn't.

Fixes: a470a51c ('mpt3sas: Handle active cable exception event')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replaced mpt3sas_base_flush_reply_queues() with
mpt3sas_base_sync_reply_irqs(),as mpt3sas_base_flush_reply_queues()
skips over reply queues that are currently busy (i.e. being handled by
interrupt processing in another core). If a reply queue is busy, then
call to synchronize_irq()in mpt3sas_base_sync_reply_irqs()make sures the
other core has finished flushing the queue and completed any calls to
the mid-layer scsi_done() routine.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Set maximum transfer length per IO on RAID volumes to 4MB by setting
VD's queue's max_sector to 8192.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Bump mpt3sas driver version from 12.100.00.00 to 13.100.00.00
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Modified driver code to use scsi_prot_ref_tag() API instead of
scsi_get_lba(), while initializing reference tag field in the CDB.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In-order to handle this 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
driver need to follow below steps,
1. Unmask the 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
so that FW can notify this event to host driver.
2. After receiving this event, add this event to AEN event queue,
for notifying this event to applications.
3. Then Print below message in kernel logs if the event data's reason
code is zero,
"Currently an active cable with ReceptacleID <ID_Value> cannot be powered
and devices connected to this active cable will not be seen. This active
cable requires <PowerValue_in_mW> of power"

This event is only for Intruder/Cutlass HBAs.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updated MPI version and MPI header files.

ChangeList:
* Added SATADeviceWaitTime to SAS IO Unit Page 4
* Added EEDPObservedValue added to SCSI IO Reply message
* Added MPI2_EVENT_ACTIVE_CABLE_EXCEPTION and
  MPI26_EVENT_DATA_ACTIVE_CABLE_EXCEPT
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Firmware events are queued up using the fw_event_work's struct work, not
its delayed_work member.  The initial driver for SAS2 controllers had
handled firmware reset using the rescan barrier and was later redesigned
through "mpt2sas: [Resend] Host Reset code cleanup".  The delayed_work
variables are now unused and may provoke CONFIG_DEBUG_OBJECTS_TIMERS
"assert_init not available" false warnings in
_scsih_fw_event_cleanup_queue.

Cleanup fw_event_work's unused entries, update its kerneldoc, and
update _scsih_fw_event_cleanup_queue accordingly.

Fixes: 146b16c8 (mpt3sas: Refcount fw_events and fix unsafe list usage)
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

'struct timeval' will have its tv_sec value overflow on 32-bit systems
in year 2038 and beyond. This patch replaces the use of struct timeval
for computing mpi_request.TimeStamp, and instead uses ktime_t which
provides 64-bit seconds value. The timestamp computed remains
unaffected (milliseconds since Unix epoch).
Signed-off-by: NTina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.

Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.

Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: NMing Lin <ming.l@ssi.samsung.com>
Acked-by: NTejun Heo <tj@kernel.org>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In _base_make_ioc_operational(), we walk ioc->reply_queue_list and pull
a pointer out of successive elements of ioc->reply_post[] for each entry
in that list if RDPQ is enabled.

Since the code pulls the pointer for the next iteration at the bottom of
the loop, it triggers the a KASAN dump on the final iteration:

    BUG: KASAN: slab-out-of-bounds in _base_make_ioc_operational+0x47b7/0x47e0 [mpt3sas] at addr ffff880754816ab0
    Read of size 8 by task modprobe/305
    <snip>
    Call Trace:
     [<ffffffff81dfc591>] dump_stack+0x4d/0x6c
     [<ffffffff814c9689>] print_trailer+0xf9/0x150
     [<ffffffff814ceda4>] object_err+0x34/0x40
     [<ffffffff814d1231>] kasan_report_error+0x221/0x530
     [<ffffffff814d1673>] __asan_report_load8_noabort+0x43/0x50
     [<ffffffffa0043637>] _base_make_ioc_operational+0x47b7/0x47e0 [mpt3sas]
     [<ffffffffa0049a51>] mpt3sas_base_attach+0x1991/0x2120 [mpt3sas]
     [<ffffffffa0053c93>] _scsih_probe+0xeb3/0x16b0 [mpt3sas]
     [<ffffffff81ebd047>] local_pci_probe+0xc7/0x170
     [<ffffffff81ebf2cf>] pci_device_probe+0x20f/0x290
     [<ffffffff820d50cd>] really_probe+0x17d/0x600
     [<ffffffff820d56a3>] __driver_attach+0x153/0x190
     [<ffffffff820cffac>] bus_for_each_dev+0x11c/0x1a0
     [<ffffffff820d421d>] driver_attach+0x3d/0x50
     [<ffffffff820d378a>] bus_add_driver+0x44a/0x5f0
     [<ffffffff820d666c>] driver_register+0x18c/0x3b0
     [<ffffffff81ebcb76>] __pci_register_driver+0x156/0x200
     [<ffffffffa00c8135>] _mpt3sas_init+0x135/0x1000 [mpt3sas]
     [<ffffffff81000423>] do_one_initcall+0x113/0x2b0
     [<ffffffff813caa5a>] do_init_module+0x1d0/0x4d8
     [<ffffffff81273909>] load_module+0x6729/0x8dc0
     [<ffffffff81276123>] SYSC_init_module+0x183/0x1a0
     [<ffffffff8127625e>] SyS_init_module+0xe/0x10
     [<ffffffff828fe7d7>] entry_SYSCALL_64_fastpath+0x12/0x6a

Fix this by pulling the value at the beginning of the loop.
Signed-off-by: NCalvin Owens <calvinowens@fb.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NJens Axboe <axboe@fb.com>
Acked-by: NChaitra Basappa <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Calling synchronize_irq() right before free_irq() is quite useless. On
one hand the IRQ can easily fire again before free_irq() is entered, on
the other hand free_irq() itself calls synchronize_irq() internally (in
a race condition free way), before any state associated with the IRQ is
freed.

Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
 free_irq(irq, ...);
// </smpl>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Deallocate resources before reallocating of the same in retry_allocation
path of _base_allocate_memory_pools()
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Remove cpumask_clear for zalloc_cpumask_var and don't free free_cpu_mask_var before reply_q

Removed cpumask_clear as it is not required for zalloc_cpumask_var and
free free_cpumask_var before freeing reply_q.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Bump mpt3sas driver version from 09.102.00.00 to 12.100.00.00
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Track msix of each IO and use the same msix for issuing abort to timed
out IO. With this driver will process IO's reply first followed by TM.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updated MPI version and MPI header files.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added support for configurable Chain Frame Size. Calculate the
Chain Message Frame size from the IOCMaxChainSegementSize (iocfacts).
Applicable only for mpt3sas/SAS3.0 HBA's.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Module parameter to enable/disable configuring affinity hint for msix
vector.  SMP affinity feature can be enabled/disabled by setting module
parameter "smp_affinity_enable" to 1/0.  By default this feature is
enabled. (smp_affinity_enable = 1 enabled).
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver assumes HighPriority credit as part of Global credit. But,
Firmware treats HighPriority credit value and global cedits as two
different values. Changed host queue algorithm to treat global credits
and highPriority credits as two different values.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Never block the SEP device (i.e. Never invoke the
scsi_internal_device_block() API for SEP device) even for the delay not
responding events. Blocking the SEP device will create a deadlock while
adding any device to the OS.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1.Wrong size of argument is being passed
 The size of struct being passed as an argument to memset func and area of
 memory being pointed by an instance of struct in memset func should be of
 same structure type.
2.Dereference null return value
3.Array compared against '0'
 Check whether value pointed by particular index of an array is null or not
 in "if" statement.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

As driver was using MPI SGL while framing the SMP Passthrough request
message due to which firmware unable to post the Reply Data in the host
memory and timeout is observed for this SMP Passthrough request message
and so unable to perform phy disable operation.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updated hardware description headers with MPI v2.6 and
mpt3sas_pci_table[] with vendor_ids, device_ids of Cutlass and Intruder
HBA which have support for 4 ports.
Signed-off-by: NSuganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: NChaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

It might happen that we try to free an already freed pointer.
Reported-by: NMaurizio Lombardi <mlombard@redhat.com>
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: NChaitra P B <chaitra.basappa@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The non-PCI builds of the O day test project are failing:

On Thu, 2015-12-03 at 05:02 +0800, kbuild test robot wrote:
> warning: (SCSI_MPT2SAS) selects SCSI_MPT3SAS which has unmet direct
> dependencies (SCSI_LOWLEVEL && PCI && SCSI)

The problem is that select and depend don't interact because Kconfig doesn't
have a SAT solver, so depend picks up dependencies and select does onward
selects, but select doesn't pick up dependencies.  To fix this, we need to add
the correct dependencies to the MPT2SAS option like this.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Fixes: b840c362Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The mpt2sas driver was recently folded into mpt3sas to reduce code
duplication.

To avoid problems for people that only have CONFIG_SCSI_MPT2SAS in their
.config we introduce a dummy option that will select MPT3SAS if MPT2SAS
was previously enabled.

This is a temporary measure and we will deprecate this config option in
4.6.
Reported-by: NPeter Zijlstra <peterz@infradead.org>
Acked-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJames Bottomley <James.Bottomley@hansenpartnership.com>
CC: Ingo Molnar <mingo@kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag in MPI SCSI IO request
message, check whether TLR is enabled on the drive using
'sas_is_tlr_enabled' API.

Actually in the driver code, driver is using below API's

1. sas_enable_tlr() - to enable the TLR
2. sas_disable_tlr() - to disable the TLR
3. sas_is_tlr_enabled() - to check whether TLR is enabled or not.

but in scsih_qcmd() we have missed to use sas_is_tlr_enabled() API,
instead we checking for TLR bit from flag field of driver's 'struct
MPT3SAS_DEVIC' structure. which is corrected with this patch.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

After merging the scsi tree, today's linux-next build (powerpc
allyesconfig) failed like this:

In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0:
drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function '_scsih_io_done':
drivers/scsi/mpt3sas/mpt3sas_base.h:1414:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_get': function body not available
 mpt3sas_scsi_direct_io_get(struct MPT3SAS_ADAPTER *ioc, u16 smid);
 ^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4448:6: error: called from here
  if (mpt3sas_scsi_direct_io_get(ioc, smid) &&
      ^
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:59:0:
drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available
 mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io);
 ^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here
   mpt3sas_scsi_direct_io_set(ioc, smid, 0);
   ^
In file included from drivers/scsi/mpt3sas/mpt3sas_scsih.c:5
9:0:
drivers/scsi/mpt3sas/mpt3sas_base.h:1416:1: error: inlining failed in call to always_inline 'mpt3sas_scsi_direct_io_set': function body not available
 mpt3sas_scsi_direct_io_set(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 direct_io);
 ^
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4454:3: error: called from here
   mpt3sas_scsi_direct_io_set(ioc, smid, 0);
   ^

Presumably caused by commit

  c84b06a4 ("mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs")
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Bump mpt3sas driver version to 09.102.00.00
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Modified the mpt3sas driver to have a single driver module which
supports both SAS 2.0 & SAS 3.0 HBA devices.

* Added SAS 2.0 HBA device IDs to the mpt3sas_pci_table pci table.

* Created two separate SCSI host templates for SAS2 and SAS3 HBAs so
  that, during the driver load time driver can use corresponding host
  template(based the pci device ID) while registering a scsi host
  adapter instance for that pci device.

* Registered two IOCTL devices, mpt2ctl is for SAS2 HBAs & mpt3ctl for
  SAS3 HBAs. Also updated the code to make sure that mpt2ctl device
  processes only those ioctl cmds issued for the SAS2 HBAs and mpt3ctl
  device processes only those ioctl cmds issued for the SAS3 HBAs.

* Added separate indexing for SAS2 and SAS3 HBAs.

* Replaced compile time check 'MPT2SAS_SCSI' to run time check
  'hba_mpi_version_belonged' whereever needed.

* Aliased this merged driver to mpt2sas using MODULE_ALIAS.

* Moved global varaible 'driver_name' to per adapter instance variable.

* Created two raid function template and used corresponding raid
  function templates based on the run time check
  'hba_mpi_version_belonged'.

* Moved mpt2sas_warpdrive.c file from mpt2sas to mpt3sas folder and
  renamed it as mpt3sas_warpdrive.c.

* Also renamed the functions in mpt3sas_warpdrive.c file to follow
  current driver function name convention.

* Updated the Makefile to build mpt3sas_warpdrive.o file for these
  WarpDrive-specific functions.

* Also in function mpt3sas_setup_direct_io(), used sector_div() API
  instead of division operator (which gives compilation errors on 32 bit
  machines).

* Removed mpt2sas files, mpt2sas directory & mpt3sas_module.c file.

* Added module parameter 'hbas_to_enumerate' which permits using this
  merged driver as a legacy mpt2sas driver or as a legacy mpt3sas
  driver.

  Here are the available options for this module parameter:

   0 - Merged driver which enumerates both SAS 2.0 & SAS 3.0 HBAs
   1 - Acts as legacy mpt2sas driver, which enumerates only SAS 2.0 HBAs
   2 - Acts as legacy mpt3sas driver, which enumerates only SAS 3.0 HBAs

* Removed mpt2sas entries from SCSI's Kconfig and Makefile files.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Bump the mpt2sas driver version to 20.102.00.00 and
Bump the mpt3sas driver version to 9.101.00.00.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

setpci reset on nytro warpdrive card along with sysfs access and cli
ioctl access resulted in kernel oops

1. pci_access_mutex lock added to provide synchronization between IOCTL,
   sysfs, PCI resource handling path

2. gioc_lock spinlock to protect list operations over multiple
   controllers

This patch is ported from commit 6229b414 ("mpt2sas: setpci reset
kernel oops fix").
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added OEM Gen2 PnP ID branding names from mpt2sas driver.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The fw_event_work struct is concurrently referenced at shutdown. Add a
refcount to protect it and refactor the code to use it.

Additionally, refactor _scsih_fw_event_cleanup_queue() such that it no
longer iterates over the list without holding the lock since
_firmware_event_work() concurrently deletes items from the list.

This patch is ported from commit 008549f6 ("mpt2sas: Refcount
fw_events and fix unsafe list usage"). These changes are also required
for mpt3sas.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

sas_device objects can be referenced concurrently throughout the driver.
We need a way to make sure threads can't delete them out from under each
other. This patch adds the refcount and refactors the code to use it.

Additionally, we cannot iterate over the sas_device_list without holding
the lock or we risk corrupting random memory if items are added or
deleted as we iterate. This patch refactors _scsih_probe_sas() to use
the sas_device_list in a safe way.

This patch is ported from the following mpt2sas driver commit
d224fe0d ("mpt2sas: Refcount sas_device objects and fix unsafe list
usage").
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>