This driver is an AC97 codec according to its help text.  However, if SOUND is
disabled, the "select SND_AC97_BUS" still inserts that into the .config file:

#
# Sound
#
# CONFIG_SOUND is not set
CONFIG_SND_AC97_BUS=m

Even if the config software followed dependency chains on selects, we should
try to limit usage of "select" to library-type code that is needed (e.g., CRC
functions) instead of bus-type support.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NRick Koch <n1gp@hotmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NRick Koch <n1gp@hotmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NRick Koch <n1gp@hotmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Most of the reasons for keeping these separate before was due to hp690
discontig, and since we have a workaround for that now (abusing some shadow
space so everything is magically contiguous), there's no reason to keep the
targets separate.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is a driver for the ADS7846 touchscreen sensor, derived from
the corgi_ts and omap_ts drivers.  Key differences from those two:

  - Uses the new SPI framework (minimalist version)
  - <linux/spi/ads7846.h> abstracts board-specific touchscreen info
  - Sysfs attributes for the temperature and voltage sensors
  - Uses fewer ARM-specific IRQ primitives

The temperature and voltage sensors show up in sysfs like this:

  $ pwd
  /sys/devices/platform/omap-uwire/spi2.0
  $ ls
  bus@          input:event0@ power/        temp1         vbatt
  driver@       modalias      temp0         vaux
  $ cat modalias
  ads7846
  $ cat temp0
  991
  $ cat temp1
  1177
  $

So far only basic testing has been done.  There's a fair amount of hardware
that uses this sensor, and which also runs Linux, which should eventually
be able to use this driver.

One portability note may be of special interest.  It turns out that not all
SPI controllers are happy issuing requests that do things like "write 8 bit
command, read 12 bit response".  Most of them seem happy to handle various
word sizes, so the issue isn't "12 bit response" but rather "different rx
and tx write sizes", despite that being a common MicroWire convention.  So
this version of the driver no longer reads 12 bit native-endian words; it
reads 16-bit big-endian responses, then byteswaps them and shifts the
results to discard the noise.
Signed-off-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Separate out the Sharp Zaurus c7x0 series specific code from the Corgi
Touchscreen driver.  Use the new functions in corgi_lcd.c via sharpsl.h for
hsync handling and pass the IRQ as a platform device resource.  Move a
function prototype into the w100fb header file where it belongs.

This enables the driver to be used by the Zaurus cxx00 series.
Signed-Off-by: NRichard Purdie <rpurdie@rpsys.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NVojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!