The efi boot stub tries to read the entire initrd in 1 go, however
some efi implementations hang if too much if asked to read too much
data at the same time. After some experimentation I found out that my
asrock p67 board will hang if asked to read chunks of 4MiB, so use a
safe value.

elilo reads in chunks of 16KiB, but since that requires many read
calls I use a value of 1 MiB.  hpa suggested adding individual
blacklists for when systems are found where this value causes a crash.
Signed-off-by: NMaarten Lankhorst <m.b.lankhorst@gmail.com>
Link: http://lkml.kernel.org/r/4EEB3A02.3090201@gmail.comSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

There is currently a large divide between kernel development and the
development of EFI boot loaders. The idea behind this patch is to give
the kernel developers full control over the EFI boot process. As
H. Peter Anvin put it,

"The 'kernel carries its own stub' approach been very successful in
dealing with BIOS, and would make a lot of sense to me for EFI as
well."

This patch introduces an EFI boot stub that allows an x86 bzImage to
be loaded and executed by EFI firmware. The bzImage appears to the
firmware as an EFI application. Luckily there are enough free bits
within the bzImage header so that it can masquerade as an EFI
application, thereby coercing the EFI firmware into loading it and
jumping to its entry point. The beauty of this masquerading approach
is that both BIOS and EFI boot loaders can still load and run the same
bzImage, thereby allowing a single kernel image to work in any boot
environment.

The EFI boot stub supports multiple initrds, but they must exist on
the same partition as the bzImage. Command-line arguments for the
kernel can be appended after the bzImage name when run from the EFI
shell, e.g.

Shell> bzImage console=ttyS0 root=/dev/sdb initrd=initrd.img

v7:
 - Fix checkpatch warnings.

v6:

 - Try to allocate initrd memory just below hdr->inird_addr_max.

v5:

 - load_options_size is UTF-16, which needs dividing by 2 to convert
   to the corresponding ASCII size.

v4:

 - Don't read more than image->load_options_size

v3:

 - Fix following warnings when compiling CONFIG_EFI_STUB=n

   arch/x86/boot/tools/build.c: In function ‘main’:
   arch/x86/boot/tools/build.c:138:24: warning: unused variable ‘pe_header’
   arch/x86/boot/tools/build.c:138:15: warning: unused variable ‘file_sz’

 - As reported by Matthew Garrett, some Apple machines have GOPs that
   don't have hardware attached. We need to weed these out by
   searching for ones that handle the PCIIO protocol.

 - Don't allocate memory if no initrds are on cmdline
 - Don't trust image->load_options_size

Maarten Lankhorst noted:
 - Don't strip first argument when booted from efibootmgr
 - Don't allocate too much memory for cmdline
 - Don't update cmdline_size, the kernel considers it read-only
 - Don't accept '\n' for initrd names

v2:

 - File alignment was too large, was 8192 should be 512. Reported by
   Maarten Lankhorst on LKML.
 - Added UGA support for graphics
 - Use VIDEO_TYPE_EFI instead of hard-coded number.
 - Move linelength assignment until after we've assigned depth
 - Dynamically fill out AddressOfEntryPoint in tools/build.c
 - Don't use magic number for GDT/TSS stuff. Requested by Andi Kleen
 - The bzImage may need to be relocated as it may have been loaded at
   a high address address by the firmware. This was required to get my
   macbook booting because the firmware loaded it at 0x7cxxxxxx, which
   triggers this error in decompress_kernel(),

	if (heap > ((-__PAGE_OFFSET-(128<<20)-1) & 0x7fffffff))
		error("Destination address too large");

Cc: Mike Waychison <mikew@google.com>
Cc: Matthew Garrett <mjg@redhat.com>
Tested-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1321383097.2657.9.camel@mfleming-mobl1.ger.corp.intel.comSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Introduce a symbol, EFI_LOADER_SIGNATURE instead of using the magic
strings, which also helps to reduce the amount of ifdeffery.

Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1318848017-12301-1-git-send-email-matt@console-pimps.orgSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

commit 37ba7ab5 ("x86, boot: make kernel_alignment adjustable; new
bzImage fields") introduced some new fields into the bzImage header
but struct setup_header was not updated accordingly. Add the missing
'pref_address' and 'init_size' fields.
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1318848017-12301-1-git-send-email-matt@console-pimps.orgSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

efi_call_phys_prelog() sets up a 1:1 mapping of the physical address
range in swapper_pg_dir. Instead of replacing then restoring entries
in swapper_pg_dir we should be using initial_page_table which already
contains the 1:1 mapping.

It's safe to blindly switch back to swapper_pg_dir in the epilog
because the physical EFI routines are only called before
efi_enter_virtual_mode(), e.g. before any user processes have been
forked. Therefore, we don't need to track which pgd was in %cr3 when
we entered the prelog.

The previous code actually contained a bug because it assumed that the
kernel was loaded at a physical address within the first 8MB of ram,
usually at 0x100000. However, this isn't the case with a
CONFIG_RELOCATABLE=y kernel which could have been loaded anywhere in
the physical address space.

Also delete the ancient (and bogus) comments about the page table
being restored after the lock is released. There is no locking.

Cc: Matthew Garrett <mjg@redhat.com>
Cc: Darrent Hart <dvhart@linux.intel.com>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1323346250.3894.74.camel@mfleming-mobl1.ger.corp.intel.comSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>

With the 3.2-rc kernel, IOMMU 2M pages in KVM works.  But when I tried
to use IOMMU 1GB pages in KVM, I encountered an oops and the 1GB page
failed to be used.

The root cause is that 1GB page allocation calls gup_huge_pud() while 2M
page calls gup_huge_pmd.  If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that.

So when the mapped page is relesed, it will result in kernel oops
because the page is not marked mapped.

This patch add tail process for compound page in 1GB huge page which
keeps the same process as 2M page.

Reproduce like:
1. Add grub boot option: hugepagesz=1G hugepages=8
2. mount -t hugetlbfs -o pagesize=1G hugetlbfs /dev/hugepages
3. qemu-kvm -m 2048 -hda os-kvm.img -cpu kvm64 -smp 4 -mem-path /dev/hugepages
	-net none -device pci-assign,host=07:00.1

  kernel BUG at mm/swap.c:114!
  invalid opcode: 0000 [#1] SMP
  Call Trace:
    put_page+0x15/0x37
    kvm_release_pfn_clean+0x31/0x36
    kvm_iommu_put_pages+0x94/0xb1
    kvm_iommu_unmap_memslots+0x80/0xb6
    kvm_assign_device+0xba/0x117
    kvm_vm_ioctl_assigned_device+0x301/0xa47
    kvm_vm_ioctl+0x36c/0x3a2
    do_vfs_ioctl+0x49e/0x4e4
    sys_ioctl+0x5a/0x7c
    system_call_fastpath+0x16/0x1b
  RIP  put_compound_page+0xd4/0x168
Signed-off-by: NYouquan Song <youquan.song@intel.com>
Reviewed-by: NAndrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If we encounter an efi_memory_desc_t without EFI_MEMORY_WB set
in ->attribute we currently call set_memory_uc(), which in turn
calls __pa() on a potentially ioremap'd address.

On CONFIG_X86_32 this is invalid, resulting in the following
oops on some machines:

  BUG: unable to handle kernel paging request at f7f22280
  IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210
  [...]

  Call Trace:
   [<c104f8ca>] ? page_is_ram+0x1a/0x40
   [<c1025aff>] reserve_memtype+0xdf/0x2f0
   [<c1024dc9>] set_memory_uc+0x49/0xa0
   [<c19334d0>] efi_enter_virtual_mode+0x1c2/0x3aa
   [<c19216d4>] start_kernel+0x291/0x2f2
   [<c19211c7>] ? loglevel+0x1b/0x1b
   [<c19210bf>] i386_start_kernel+0xbf/0xc8

A better approach to this problem is to map the memory region
with the correct attributes from the start, instead of modifying
it after the fact. The uncached case can be handled by
ioremap_nocache() and the cached by ioremap_cache().

Despite first impressions, it's not possible to use
ioremap_cache() to map all cached memory regions on
CONFIG_X86_64 because EFI_RUNTIME_SERVICES_DATA regions really
don't like being mapped into the vmalloc space, as detailed in
the following bug report,

	https://bugzilla.redhat.com/show_bug.cgi?id=748516

Therefore, we need to ensure that any EFI_RUNTIME_SERVICES_DATA
regions are covered by the direct kernel mapping table on
CONFIG_X86_64. To accomplish this we now map E820_RESERVED_EFI
regions via the direct kernel mapping with the initial call to
init_memory_mapping() in setup_arch(), whereas previously these
regions wouldn't be mapped if they were after the last E820_RAM
region until efi_ioremap() was called. Doing it this way allows
us to delete efi_ioremap() completely.
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console-pimps.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>

When HPET is operating in RTC mode, the TN_ENABLE bit on timer1
controls whether the HPET or the RTC delivers interrupts to irq8. When
the system goes into suspend, the RTC driver sends a signal to the
HPET driver so that the HPET releases control of irq8, allowing the
RTC to wake the system from suspend. The switchover is accomplished by
a write to the HPET configuration registers which currently only
occurs while servicing the HPET interrupt.

On some systems, I have seen the system suspend before an HPET
interrupt occurs, preventing the write to the HPET configuration
register and leaving the HPET in control of the irq8. As the HPET is
not active during suspend, it does not generate a wake signal and RTC
alarms do not work.

This patch forces the HPET driver to immediately transfer control of
the irq8 channel to the RTC instead of waiting until the next
interrupt event.
Signed-off-by: NMark Langsdorf <mark.langsdorf@amd.com>
Link: http://lkml.kernel.org/r/20111118153306.GB16319@alberich.amd.comTested-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org

If we select a symbol it should have a type declared first
otherwise in some situations the config tools get upset. They
are currently perhaps a bit too resilient which is why this
wasn't noticed initially.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111206132811.4041.32549.stgit@bob.linux.org.ukSigned-off-by: NIngo Molnar <mingo@elte.hu>

We currently fail to build on CONFIG_X86_INTEL_MID=y and
CONFIG_X86_MRST unset.

We could build all the bits to make generic MID work if you
picked MID platform alone but that's really silly. Instead use
select and two variables.

This looks a bit daft right now but once we add a Medfield
selection it'll start to look a good deal more sensible.
Reported-by: NIngo Molnar <mingo@elte.hu>
Reported-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111205231433.28811.51297.stgit@bob.linux.org.ukSigned-off-by: NIngo Molnar <mingo@elte.hu>

I've received complaints that the numa_node attribute for family
15h model 00-0fh (e.g. Interlagos) northbridge functions shows
-1 instead of the proper node ID.

Correct this with attached quirks (similar to quirks for other
AMD CPU families used in multi-socket systems).
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Cc: Frank Arnold <frank.arnold@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/20111202072143.GA31916@alberich.amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Intel MID x86 platforms have a memory mapped virtual RTC
instead.  No MID platform have the default ports (and
accessing them may do weird stuff).
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: feng.tang@intel.com
Cc: Feng Tang <feng.tang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Fix an outstanding issue that has been reported since 2.6.37.
Under a heavy loaded machine processing "fork()" calls could
crash with:

BUG: unable to handle kernel paging request at f573fc8c
IP: [<c01abc54>] swap_count_continued+0x104/0x180
*pdpt = 000000002a3b9027 *pde = 0000000001bed067 *pte = 0000000000000000 Oops: 0000 [#1] SMP
Modules linked in:
Pid: 1638, comm: apache2 Not tainted 3.0.4-linode37 #1
EIP: 0061:[<c01abc54>] EFLAGS: 00210246 CPU: 3
EIP is at swap_count_continued+0x104/0x180
.. snip..
Call Trace:
 [<c01ac222>] ? __swap_duplicate+0xc2/0x160
 [<c01040f7>] ? pte_mfn_to_pfn+0x87/0xe0
 [<c01ac2e4>] ? swap_duplicate+0x14/0x40
 [<c01a0a6b>] ? copy_pte_range+0x45b/0x500
 [<c01a0ca5>] ? copy_page_range+0x195/0x200
 [<c01328c6>] ? dup_mmap+0x1c6/0x2c0
 [<c0132cf8>] ? dup_mm+0xa8/0x130
 [<c013376a>] ? copy_process+0x98a/0xb30
 [<c013395f>] ? do_fork+0x4f/0x280
 [<c01573b3>] ? getnstimeofday+0x43/0x100
 [<c010f770>] ? sys_clone+0x30/0x40
 [<c06c048d>] ? ptregs_clone+0x15/0x48
 [<c06bfb71>] ? syscall_call+0x7/0xb

The problem is that in copy_page_range() we turn lazy mode on,
and then in swap_entry_free() we call swap_count_continued()
which ends up in:

         map = kmap_atomic(page, KM_USER0) + offset;

and then later we touch *map.

Since we are running in batched mode (lazy) we don't actually
set up the PTE mappings and the kmap_atomic is not done
synchronously and ends up trying to dereference a page that has
not been set.

Looking at kmap_atomic_prot_pfn(), it uses
'arch_flush_lazy_mmu_mode' and doing the same in
kmap_atomic_prot() and __kunmap_atomic() makes the problem go
away.

Interestingly, commit b8bcfe99 ("x86/paravirt: remove lazy
mode in interrupts") removed part of this to fix an interrupt
issue - but it went to far and did not consider this scenario.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Looks like on some Acer Aspire 1s with older bioses, reboot via bios
fails.  It works on my machine, (with BIOS version 0.3310) but
not on some others (BIOS version 0.3309).

There's a log of problems at:

  https://bbs.archlinux.org/viewtopic.php?id=124136

This patch adds a different callback to the reboot quirk table,
to allow rebooting via keybaord controller.
Reported-by: NUroš Vampl <mobile.leecher@gmail.com>
Tested-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NPeter Chubb <peter.chubb@nicta.com.au>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1323093233-9481-1-git-send-email-anarsoul@gmail.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Following is from Notes of section 11.5.3 of Intel processor
manual available at:

  http://www.intel.com/Assets/PDF/manual/325384.pdf

For the Pentium 4 and Intel Xeon processors, after the sequence of
steps given above has been executed, the cache lines containing the
code between the end of the WBINVD instruction and before the
MTRRS have actually been disabled may be retained in the cache
hierarchy. Here, to remove code from the cache completely, a
second WBINVD instruction must be executed after the MTRRs have
been disabled.

This patch provides resolution for that.

Ideally, I will like to make changes only for Pentium 4 and Xeon
processors. But, I am not finding easier way to do it.
And, extra wbinvd() instruction does not hurt much for other
processors.
Signed-off-by: NAjaykumar Hotchandani <ajaykumar.hotchandani@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Link: http://lkml.kernel.org/r/4EBD1CC5.3030008@oracle.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Recently, I got bitten by using rdmsr_safe too early in the boot
process. Document its shortcomings for future reference.

Link: http://lkml.kernel.org/r/4ED5B70F.606@lwfinger.netSigned-off-by: NBorislav Petkov <borislav.petkov@amd.com>

The microcode update driver's initialization code does not handle
failures correctly. This patch fixes this issue.
Signed-off-by: NJan Beulich <JBeulich@suse.com>
Signed-off-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20111107123530.12164.31227.stgit@srivatsabhat.in.ibm.com
Link: http://lkml.kernel.org/r/4ED8E2270200007800065120@nat28.tlf.novell.comSigned-off-by: NBorislav Petkov <borislav.petkov@amd.com>

TAINT_FIRMWARE_WORKAROUND should be set when an MTRR fixup
is done.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1318958650-12447-1-git-send-email-prarit@redhat.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

In commit f8924e77 ("x86: unify mp_bus_info"), the 32-bit
and 64-bit versions of MP_bus_info were rearranged to match each
other better.  Unfortunately it introduced a regression: prior
to that change we used to always set the mp_bus_not_pci bit,
then clear it if we found a PCI bus.  After it, we set
mp_bus_not_pci for ISA buses, clear it for PCI buses, and leave
it alone otherwise.

In the cases of ISA and PCI, there's not much difference.  But
ISA is not the only non-PCI bus, so it's better to always set
mp_bus_not_pci and clear it only for PCI.

Without this change, Dan's Dell PowerEdge 4200 panics on boot
with a log indicating interrupt routing trouble unless the
"noapic" option is supplied.  With this change, the machine
boots reliably without "noapic".

Fixes http://bugs.debian.org/586494Reported-bisected-and-tested-by: NDan McGrath <troubledaemon@gmail.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org	# 2.6.26+
Cc: Dan McGrath <troubledaemon@gmail.com>
Cc: Alexey Starikovskiy <aystarik@gmail.com>
[jrnieder@gmail.com: clarified commit message]
Signed-off-by: NJonathan Nieder <jrnieder@gmail.com>
Link: http://lkml.kernel.org/r/20111122215000.GA9151@elie.hsd1.il.comcast.netSigned-off-by: NIngo Molnar <mingo@elte.hu>

In latest firmware's SFI tables, pmic_gpio has been set to
IPC type of device, so we need handle it too.
Signed-off-by: NFeng Tang <feng.tang@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Add SFI glue for the following devices:

tca6416: a gpio expander compatible with max7315
mpu3050: gyro sensor

Both of these actual drivers are already upstream
Signed-off-by: NJekyll Lai <jekyll_lai@wistron.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

On the Intel MID devices SCU commands are issued to manage power
off and the like. We need to issue different ones for
non-Lincroft based devices.
Signed-off-by: NAlek Du <alek.du@intel.com>
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Dell OptiPlex 990 is known to require PCI reboot, so add it to
the reboot blacklist in pci_reboot_dmi_table[].
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Link: http://lkml.kernel.org/r/201111160019.51303.rjw@sisk.plSigned-off-by: NIngo Molnar <mingo@elte.hu>

There was a mixup when the SGI UV2 hub chip was sent to be
fabricated, and it ended up with the wrong part number in the
HRP_NODE_ID mmr. Future versions of the chip will (may) have the
correct part number. Change the UV infrastructure to recognize
both part numbers as valid IDs of a UV2 hub chip.
Signed-off-by: NJack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20111129210058.GA20452@sgi.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

The kernel stack overflow is checked in stack_overflow_check(),
which may wrongly detect the overflow if the stack pointer in
user space points to the kernel stack intentionally or
accidentally. So, the actual overflow is never detected after
this misdetection because WARN_ONCE() is used on the detection
of it.

This patch adds user-mode-vm checking before it to avoid this
problem and bails out early if the user stack is used.
Signed-off-by: NMitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Randy Dunlap <rdunlap@xenotime.net>
Link: http://lkml.kernel.org/r/20111129060821.11076.55315.stgit@ltc219.sdl.hitachi.co.jpSigned-off-by: NIngo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>

On AMD family 10h we see firmware bug messages like the following:

 [Firmware Bug]: cpu 6, try to use APIC500 (LVT offset 0) for vector 0x10400, but the register is already in use for vector 0xf9 on another cpu
 [Firmware Bug]: cpu 6, IBS interrupt offset 0 not available (MSRC001103A=0x0000000000000100)
 [Firmware Bug]: using offset 1 for IBS interrupts
 [Firmware Bug]: workaround enabled for IBS LVT offset
 perf: AMD IBS detected (0x00000007)

We always see this, since the offsets are not assigned by the BIOS for
this family. Force LVT offset assignment in this case. If the OS
assignment fails, fallback to BIOS settings and try to setup this.

The fallback to BIOS settings weakens the family check since
force_ibs_eilvt_setup() may fail e.g. in case of virtual machines.
But setup may still succeed if BIOS offsets are correct.

Other families don't have a workaround implemented that assigns LVT
offsets. It's ok, to drop calling force_ibs_eilvt_setup() for that
families.

With the patch the [Firmware Bug] messages vanish. We see now:

 IBS: LVT offset 1 assigned
 perf: AMD IBS detected (0x00000007)
Signed-off-by: NRobert Richter <robert.richter@amd.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111109162225.GO12451@erda.amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Cc: Stephane Eranian <eranian@google.com>
Cc: stable@kernel.org
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

People with old AMD chips are getting hung boots, because commit
bcb80e53 ("x86, microcode, AMD: Add microcode revision to
/proc/cpuinfo") moved the microcode detection too early into
"early_init_amd()".

At that point we are *so* early in the booth that the exception tables
haven't even been set up yet, so the whole

	rdmsr_safe(MSR_AMD64_PATCH_LEVEL, &c->microcode, &dummy);

doesn't actually work: if the rdmsr does a GP fault (due to non-existant
MSR register on older CPU's), we can't fix it up yet, and the boot fails.

Fix it by simply moving the code to a slightly later point in the boot
(init_amd() instead of early_init_amd()), since the kernel itself
doesn't even really care about the microcode patchlevel at this point
(or really ever: it's made available to user space in /proc/cpuinfo, and
updated if you do a microcode load).
Reported-tested-and-bisected-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NBob Tracy <rct@gherkin.frus.com>
Acked-by: NBorislav Petkov <borislav.petkov@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The idea behind commit d91ee586 ("cpuidle: replace xen access to x86
pm_idle and default_idle") was to have one call - disable_cpuidle()
which would make pm_idle not be molested by other code.  It disallows
cpuidle_idle_call to be set to pm_idle (which is excellent).

But in the select_idle_routine() and idle_setup(), the pm_idle can still
be set to either: amd_e400_idle, mwait_idle or default_idle.  This
depends on some CPU flags (MWAIT) and in AMD case on the type of CPU.

In case of mwait_idle we can hit some instances where the hypervisor
(Amazon EC2 specifically) sets the MWAIT and we get:

  Brought up 2 CPUs
  invalid opcode: 0000 [#1] SMP

  Pid: 0, comm: swapper Not tainted 3.1.0-0.rc6.git0.3.fc16.x86_64 #1
  RIP: e030:[<ffffffff81015d1d>]  [<ffffffff81015d1d>] mwait_idle+0x6f/0xb4
  ...
  Call Trace:
   [<ffffffff8100e2ed>] cpu_idle+0xae/0xe8
   [<ffffffff8149ee78>] cpu_bringup_and_idle+0xe/0x10
  RIP  [<ffffffff81015d1d>] mwait_idle+0x6f/0xb4
   RSP <ffff8801d28ddf10>

In the case of amd_e400_idle we don't get so spectacular crashes, but we
do end up making an MSR which is trapped in the hypervisor, and then
follow it up with a yield hypercall.  Meaning we end up going to
hypervisor twice instead of just once.

The previous behavior before v3.0 was that pm_idle was set to
default_idle regardless of select_idle_routine/idle_setup.

We want to do that, but only for one specific case: Xen.  This patch
does that.

Fixes RH BZ #739499 and Ubuntu #881076
Reported-by: NStefan Bader <stefan.bader@canonical.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

wrong register returned...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Prevent tracing of preempt_disable() in get_cpu_var() in
kvm_clock_read(). When CONFIG_DEBUG_PREEMPT is enabled,
preempt_disable/enable() are traced and this causes the function_graph
tracer to go into an infinite recursion. By open coding the
preempt_disable() around the get_cpu_var(), we can use the notrace
version which prevents preempt_disable/enable() from being traced and
prevents the recursion.

Based on a similar patch for Xen from Jeremy Fitzhardinge.
Tested-by: NGleb Natapov <gleb@redhat.com>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Support guest/host-only profiling by switch perf msrs on
a guest entry if needed.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Some cpus have special support for switching PERF_GLOBAL_CTRL msr.
Add logic to detect if such support exists and works properly and extend
msr switching code to use it if available. Also extend number of generic
msr switching entries to 8.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

(Added the missing signed-off-by line)

In hundreds of days, the __cycles_2_ns calculation in sched_clock
has an overflow.  cyc * per_cpu(cyc2ns, cpu) exceeds 64 bits, causing
the final value to become zero.  We can solve this without losing
any precision.

We can decompose TSC into quotient and remainder of division by the
scale factor, and then use this to convert TSC into nanoseconds.
Signed-off-by: NSalman Qazi <sqazi@google.com>
Acked-by: NJohn Stultz <johnstul@us.ibm.com>
Reviewed-by: NPaul Turner <pjt@google.com>
Cc: stable@kernel.org
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111115221121.7262.88871.stgit@dungbeetle.mtv.corp.google.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

PVHVM running with more than 32 vcpus and pv_irq/pv_time enabled
need VCPU placement to work, or else it will softlockup.

CC: stable@kernel.org
Acked-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: NZhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

When mapping a foreign page with xenbus_map_ring_valloc() with the
GNTTABOP_map_grant_ref hypercall, set the GNTMAP_contains_pte flag and
pass a pointer to the PTE (in init_mm).

After the page is mapped, the usual fault mechanism can be used to
update additional MMs.  This allows the vmalloc_sync_all() to be
removed from alloc_vm_area().
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NAndrew Morton <akpm@linux-foundation.org>
[v1: Squashed fix by Michal for no-mmu case]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NMichal Simek <monstr@monstr.eu>

It appears that stop_machine_text_poke() wants to be called on all CPUs,
like it's done from text_poke_smp().  Fix text_poke_smp_batch() to do
this.
Signed-off-by: NRabin Vincent <rabin@rab.in>
Acked-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Jason Baron <jbaron@redhat.com>
Link: http://lkml.kernel.org/r/1319702072-32676-1-git-send-email-rabin@rab.inSigned-off-by: NIngo Molnar <mingo@elte.hu>

Now that the core offcore support is fixed up (thanks Stephane) and we
have sane generic events utilizing them, re-enable the raw access to
the feature as well.

Note that it doesn't matter if you use event 0x1b7 or 0x1bb to specify
an offcore event, either one works and neither guarantees you'll end
up on a particular offcore MSR.

Based on original patch from: Vince Weaver <vweaver1@eecs.utk.edu>.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Vince Weaver <vweaver1@eecs.utk.edu>.
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1108031200390.703@cl320.eecs.utk.eduSigned-off-by: NIngo Molnar <mingo@elte.hu>

People (Linus) objected to using -ENOSPC to signal not having enough
resources on the PMU to satisfy the request. Use -EINVAL.
Requested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/n/tip-xv8geaz2zpbjhlx0svmpp28n@git.kernel.org
[ merged to newer kernel, fixed up MIPS impact ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>