Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 17 12月, 2011 1 次提交
  3. 13 12月, 2011 1 次提交
    • M
      x86, efi: EFI boot stub support · 291f3632
      由 Matt Fleming 提交于 
      There is currently a large divide between kernel development and the
development of EFI boot loaders. The idea behind this patch is to give
the kernel developers full control over the EFI boot process. As
H. Peter Anvin put it,

"The 'kernel carries its own stub' approach been very successful in
dealing with BIOS, and would make a lot of sense to me for EFI as
well."

This patch introduces an EFI boot stub that allows an x86 bzImage to
be loaded and executed by EFI firmware. The bzImage appears to the
firmware as an EFI application. Luckily there are enough free bits
within the bzImage header so that it can masquerade as an EFI
application, thereby coercing the EFI firmware into loading it and
jumping to its entry point. The beauty of this masquerading approach
is that both BIOS and EFI boot loaders can still load and run the same
bzImage, thereby allowing a single kernel image to work in any boot
environment.

The EFI boot stub supports multiple initrds, but they must exist on
the same partition as the bzImage. Command-line arguments for the
kernel can be appended after the bzImage name when run from the EFI
shell, e.g.

Shell> bzImage console=ttyS0 root=/dev/sdb initrd=initrd.img

v7:
 - Fix checkpatch warnings.

v6:

 - Try to allocate initrd memory just below hdr->inird_addr_max.

v5:

 - load_options_size is UTF-16, which needs dividing by 2 to convert
   to the corresponding ASCII size.

v4:

 - Don't read more than image->load_options_size

v3:

 - Fix following warnings when compiling CONFIG_EFI_STUB=n

   arch/x86/boot/tools/build.c: In function ‘main’:
   arch/x86/boot/tools/build.c:138:24: warning: unused variable ‘pe_header’
   arch/x86/boot/tools/build.c:138:15: warning: unused variable ‘file_sz’

 - As reported by Matthew Garrett, some Apple machines have GOPs that
   don't have hardware attached. We need to weed these out by
   searching for ones that handle the PCIIO protocol.

 - Don't allocate memory if no initrds are on cmdline
 - Don't trust image->load_options_size

Maarten Lankhorst noted:
 - Don't strip first argument when booted from efibootmgr
 - Don't allocate too much memory for cmdline
 - Don't update cmdline_size, the kernel considers it read-only
 - Don't accept '\n' for initrd names

v2:

 - File alignment was too large, was 8192 should be 512. Reported by
   Maarten Lankhorst on LKML.
 - Added UGA support for graphics
 - Use VIDEO_TYPE_EFI instead of hard-coded number.
 - Move linelength assignment until after we've assigned depth
 - Dynamically fill out AddressOfEntryPoint in tools/build.c
 - Don't use magic number for GDT/TSS stuff. Requested by Andi Kleen
 - The bzImage may need to be relocated as it may have been loaded at
   a high address address by the firmware. This was required to get my
   macbook booting because the firmware loaded it at 0x7cxxxxxx, which
   triggers this error in decompress_kernel(),

	if (heap > ((-__PAGE_OFFSET-(128<<20)-1) & 0x7fffffff))
		error("Destination address too large");

Cc: Mike Waychison <mikew@google.com>
Cc: Matthew Garrett <mjg@redhat.com>
Tested-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1321383097.2657.9.camel@mfleming-mobl1.ger.corp.intel.comSigned-off-by: NH. Peter Anvin <hpa@linux.intel.com>
      291f3632
  5. 10 12月, 2011 3 次提交
  7. 09 12月, 2011 3 次提交
    • Y
      thp: add compound tail page _mapcount when mapped · b6999b19
      由 Youquan Song 提交于 
      With the 3.2-rc kernel, IOMMU 2M pages in KVM works.  But when I tried
to use IOMMU 1GB pages in KVM, I encountered an oops and the 1GB page
failed to be used.

The root cause is that 1GB page allocation calls gup_huge_pud() while 2M
page calls gup_huge_pmd.  If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that.

So when the mapped page is relesed, it will result in kernel oops
because the page is not marked mapped.

This patch add tail process for compound page in 1GB huge page which
keeps the same process as 2M page.

Reproduce like:
1. Add grub boot option: hugepagesz=1G hugepages=8
2. mount -t hugetlbfs -o pagesize=1G hugetlbfs /dev/hugepages
3. qemu-kvm -m 2048 -hda os-kvm.img -cpu kvm64 -smp 4 -mem-path /dev/hugepages
	-net none -device pci-assign,host=07:00.1

  kernel BUG at mm/swap.c:114!
  invalid opcode: 0000 [#1] SMP
  Call Trace:
    put_page+0x15/0x37
    kvm_release_pfn_clean+0x31/0x36
    kvm_iommu_put_pages+0x94/0xb1
    kvm_iommu_unmap_memslots+0x80/0xb6
    kvm_assign_device+0xba/0x117
    kvm_vm_ioctl_assigned_device+0x301/0xa47
    kvm_vm_ioctl+0x36c/0x3a2
    do_vfs_ioctl+0x49e/0x4e4
    sys_ioctl+0x5a/0x7c
    system_call_fastpath+0x16/0x1b
  RIP  put_compound_page+0xd4/0x168
Signed-off-by: NYouquan Song <youquan.song@intel.com>
Reviewed-by: NAndrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      b6999b19
    • M
      x86, efi: Calling __pa() with an ioremap()ed address is invalid · e8c71062
      由 Matt Fleming 提交于 
      If we encounter an efi_memory_desc_t without EFI_MEMORY_WB set
in ->attribute we currently call set_memory_uc(), which in turn
calls __pa() on a potentially ioremap'd address.

On CONFIG_X86_32 this is invalid, resulting in the following
oops on some machines:

  BUG: unable to handle kernel paging request at f7f22280
  IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210
  [...]

  Call Trace:
   [<c104f8ca>] ? page_is_ram+0x1a/0x40
   [<c1025aff>] reserve_memtype+0xdf/0x2f0
   [<c1024dc9>] set_memory_uc+0x49/0xa0
   [<c19334d0>] efi_enter_virtual_mode+0x1c2/0x3aa
   [<c19216d4>] start_kernel+0x291/0x2f2
   [<c19211c7>] ? loglevel+0x1b/0x1b
   [<c19210bf>] i386_start_kernel+0xbf/0xc8

A better approach to this problem is to map the memory region
with the correct attributes from the start, instead of modifying
it after the fact. The uncached case can be handled by
ioremap_nocache() and the cached by ioremap_cache().

Despite first impressions, it's not possible to use
ioremap_cache() to map all cached memory regions on
CONFIG_X86_64 because EFI_RUNTIME_SERVICES_DATA regions really
don't like being mapped into the vmalloc space, as detailed in
the following bug report,

	https://bugzilla.redhat.com/show_bug.cgi?id=748516

Therefore, we need to ensure that any EFI_RUNTIME_SERVICES_DATA
regions are covered by the direct kernel mapping table on
CONFIG_X86_64. To accomplish this we now map E820_RESERVED_EFI
regions via the direct kernel mapping with the initial call to
init_memory_mapping() in setup_arch(), whereas previously these
regions wouldn't be mapped if they were after the last E820_RAM
region until efi_ioremap() was called. Doing it this way allows
us to delete efi_ioremap() completely.
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console-pimps.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>
      e8c71062
    • M
      x86, hpet: Immediately disable HPET timer 1 if rtc irq is masked · 2ded6e6a
      由 Mark Langsdorf 提交于 
      When HPET is operating in RTC mode, the TN_ENABLE bit on timer1
controls whether the HPET or the RTC delivers interrupts to irq8. When
the system goes into suspend, the RTC driver sends a signal to the
HPET driver so that the HPET releases control of irq8, allowing the
RTC to wake the system from suspend. The switchover is accomplished by
a write to the HPET configuration registers which currently only
occurs while servicing the HPET interrupt.

On some systems, I have seen the system suspend before an HPET
interrupt occurs, preventing the write to the HPET configuration
register and leaving the HPET in control of the irq8. As the HPET is
not active during suspend, it does not generate a wake signal and RTC
alarms do not work.

This patch forces the HPET driver to immediately transfer control of
the irq8 channel to the RTC instead of waiting until the next
interrupt event.
Signed-off-by: NMark Langsdorf <mark.langsdorf@amd.com>
Link: http://lkml.kernel.org/r/20111118153306.GB16319@alberich.amd.comTested-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
      2ded6e6a
  9. 08 12月, 2011 1 次提交
  11. 07 12月, 2011 1 次提交
  13. 06 12月, 2011 7 次提交
  15. 05 12月, 2011 21 次提交
  17. 04 12月, 2011 2 次提交