The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and
the DGE-530T uses Yukon1 so it uses skge driver.

Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If both ports are receiving on the SysKonnect dual port cards,
then it appears the bus interface unit can give an interrupt status
for frame before DMA has completed.  This leads to bogus frames
and general confusion. This is why receive checksumming is also
messed up on dual port cards.

A workaround for the out of order receive problem is to eliminating
split transactions on PCI-X.

This version is based of the current linux-2.6.git including earlier
patch to disable dual ports.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When both ports are receiving simultaneously, the receive logic gets confused
and may pass up a packet before it is full. This causes hangs, and IP will see
lots of garbage packets. There is even the potential for data corruption if
a later arriving packet DMA's into freed memory.

It looks like a hardware bug because status arrives for a packet but no
data is there. Until this bug is worked out, block the user from bringing
up both ports at once.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Bringing down a port also masks off the status and other IRQ's
needed for device to function due to missing paren's.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Update version number, to track changes.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: NStephe Hemminger <shemminger@osdl.org>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Need to make sure interrupt is not racing with unregister of
network device.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

It is more efficient not to write the status ring from the
processor and just read the active portion.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Need to make the edge-triggered workaround timer faster to get marginally
better peformance. The test_and_set_bit in schedule_prep() acts as a barrier
already. Make it a module parameter so that laptops who are concerned
about power can set it to 0; and user's stuck with broken BIOS's
can turn the driver into pure polling.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Gcc isn't smart enough to know that it can do a modulo
operation with power of 2 constant by doing a mask.
So add macro to do it for us.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Mask for transmit ring status was picking up bits from the
unused sync ring.  They were always zero, so far...
Also, make sure to remind self not to make tx ring too big.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

The status interrupt flag should be cleared before processing,
not afterwards to avoid race. Need to process in poll routine
even if no new interrupt status. This is a normal occurrence when
more than 64 frames (NAPI weight) are processed in one poll routine.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

This is a backout of earlier patch.

The whole rescheduling hack was a bad idea. It doesn't really solve
the problem and it makes the code more complicated for no good reason.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Update to version 1.2
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The sky2_reset function only called from sky2_probe.
Maybe the compiler was smart enough to figure this out already.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The ALIGN() macro in kernel.h does the same math that the
sky2 driver was using for padding.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add an fake NAPI schedule once a second. This is an attempt to work around
for broken configurations with edge-triggered interrupts.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This is a workaround for the case edge-triggered irq's. Several users
seem to have broken configurations sharing edge-triggered irq's. To avoid
losing IRQ's, reshedule if more work arrives.

The changes to netdevice.h are to extract the part that puts device
back in list into separate inline.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Sky2 driver will oops referencing bad memory if used on
a dual port card.  The problem is accessing past end of
MIB counter space.

Applies for both 2.6.17 and 2.6.16 (with fuzz)
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes the problem of some Dlink cards picking the wrong
driver.  It looks like these cards use Yukon 1 chipset, not Yukon 2.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Transmit buffers are always freed with interrupts enabled (softirq),
so we can just call dev_kfree_skb.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Unicast packets are shown as multicast, real multicast packets are missing.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Typo in last stats patch.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Expose all the available hardware statistics via ethtool.
And cleanup some of the statistics definitions.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Set version to 1.1
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The hardware has additional error trap interrupt bits.  I have never seen
them trigger, but if they do, it looks like this might be useful.
Signed-off-by: NStephen Hemminger <shemminger@osdl.rog>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch decodes state and revovers from any races in the transmit
timeout and NAPI logic. It should never trigger, but if it does then
do the right thing.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Small whitespace fixes.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add MSI support to sky2 driver.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Change default coalescing parameters slightly, and allow wider
range of values.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Redo the interupt handling of sky2 driver based on the IRQ mangement
documentation. All interrupts are handled by the device0 NAPI poll
routine.

Don't need to adjust interrupt mask in IRQ context, done only when
changing device under RTNL. Therefore don't need hwlock anymore.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove wake on lan support for now. It doesn't work right, and I
don't have a machine with working suspend/resume to test or fix it.
It will be re-enabled later.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The Yukon EC/rev0 (A1) chipset requires a bunch of workarounds. I copied these
from sk98lin.  But since they never got tested and add more cruft to the code;
any attempt at using driver as is on this version will probably fail.

It looks like this was a early engineering sample chip revision, if it ever shows
up on a real system. Produce an error message.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Turn on truncation to prevent getting choked by frames larger than expected.
Without this fix, driver hangs after receiving an oversize packet.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Avoid premature transmit ring full conditions.
Force a transmit status interrupt if transmit ring gets nearly full
and after a TSO send.

Allow more entries in transmit ring to be used if dma_addr is 32 bits
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Don't use sky2 to seed random pool beacause the network packet arrival time
will not be truly random due to NAPI and interrupt mitigation.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Remove Message Signaled Interrupt support (for 2.6.16).
MSI is inherently edge-triggered and that is incompatiable (without more
work) with NAPI.

In future, will replace with smarter lockless-IRQ handling like
tg3.c
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to avoid race in updating IRQ mask.  This can probably be replaced
smarter use of the interrupt control registers (if/when chipset
docs are available).
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

To avoid problems with PCI config access without ACPI (or busted ACPI tables),
use the device's window into PCI config space.

I know this probably will upset the purists, but I would rather have users
than ACPI testers. It also generates less code.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>

Need to force a transmit coalesce timer restart after processing
transmit packets. Otherwise, can get transmit status after last
update and chip doesn't send the next one.

Can go with the chip defaults for coalescing timers, except for
Tx timer which needs to be bigger.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>