Introduce imx6sx-sdb-sai.dts so that it is possible to use the
SAI interface.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Based on i.MX6 SoloX with 1GB of RAM.

https://boundarydevices.com/product/nit6_solox-imx6/Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This baseboard can be used with all TX6 SoMs, but only a certain set
of combinations can be ordered by default. Add support for these
combinations in mainline, so that users can easily adopt their own
combination of SoM and baseboard themselves.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for the following i.MX6 based modules from Ka-Ro
electronics GmbH:
TX6S-8034:
Processor    Freescale i.MX 6 Solo, 800MHz
RAM          256MiB DDR3 SDRAM
ROM          128MiB NAND Flash
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6S-8035:
Processor    Freescale i.MX 6 Solo, 800MHz
RAM          512MiB DDR3 SDRAM
ROM          4GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6U-8033:
Processor    Freescale i.MX 6 Dual Lite, 800MHz
RAM          1GiB DDR3 SDRAM
ROM          4GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6Q-1036:
Processor    Freescale i.MX 6Quad, 1GHz
RAM          1GB DDR3 SDRAM 64-bit
ROM          8GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  Extended Consumer Grade (-20°C to 105°C Tj)
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Based on i.MX6 Quad Plus with 4GB of RAM.

https://boundarydevices.com/product/nitrogen6max/Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The TXUL-0010/-0011 modules are Computers On Module manufactured by
  Ka-Ro electronics GmbH with the following characteristics:
  Processor    Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
  RAM          256MB 16-bit DDR3 SDRAM
  ROM          128MB NAND Flash (TXUL-0010) / 4GB eMMC (TXUL-0011)
  Power supply Single 3.3 to 5V
  Size         26mm SO-DIMM
  Temp. Range  -40°C to 85°C
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Initial commit for PH1-Pro4 Sanji board support.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Initial commit for PH1-Pro4 Ace board support.

Note:
There are two variants for the amount of DDR memory; 1GB or 2GB.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The LG Optimus Black codename sniper is a smartphone that was designed and
manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC, GP version.

This adds devicetree support for the device, with only a few basic features
supported, such as debug uart, i2c, internal emmc and external mmc.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for Advantech/GE B850v3 board.
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for Advantech/GE B650v3 board.
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for Advantech/GE B450v3 board.
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NPetr Štetiar <ynezz@true.cz>
Reviewed-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Uniwest evi is a portable electrical eddy current non-destructive
testing device.
Signed-off-by: NJoshua Clayton <stillcompiling@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch adds dts file for imx6qp-sabresd board.
Signed-off-by: NBai Ping <ping.bai@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This patch adds basic dts file for i.MX6QP-Sbreauto board.
Signed-off-by: NBai Ping <ping.bai@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q
Signed-off-by: NMichael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
Signed-off-by: NJelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add barebones K2G evm dts. This DTS allows the board to boot using a
ram based filesystem.

The technical reference manual for K2G can be found here:
http://www.ti.com/lit/ug/spruhy8/spruhy8.pdfSigned-off-by: NVitaly Andrianov <vitalya@ti.com>
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NSantosh Shilimkar <ssantosh@kernel.org>

Signed-off-by: NLars Persson <larper@axis.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This patch adds a dts file to support the Nexus7 2013
device. Its based off of the qcom-apq8064-ifc6410.dts
which is similar hardware.

Also includes some comments and context folded in
from Vinay Simha BN <simhavcs@gmail.com>

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Vinay Simha BN <simhavcs@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Acked-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

It's pretty similar to the STM32F429, but there are some
subtle changes required to boot successfully.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMaxime Coquelin <mcoquelin.stm32@gmail.com>

This adds basic chip support for Mediatek MT7623.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

Add dts file to support Buffalo Linkstation LS-GL
(a.k.a Buffalo Linkstation Pro/Live), which is marvell orion5x based
3.5" HDD NAS.

Product info:
  - (JPN) http://buffalo.jp/products/catalog/item/l/ls-gl/
  - (ENG) http://www.buffalotech.com/products/network-storage/linkstation/linkstation-pro

This device tree is based on the board file:
  arch/arm/mach-orion5x/kurobox_pro-setup.c
However, that board file also support Kurobox Pro, which is not supported by
device tree yet. So the board file is not removed.
Signed-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add dts file to support Buffalo Linkstation LS-QVL,
which is marvell kirkwood based 4-bay 3.5" HDD NAS.
Product info:
  - (JPN) http://buffalo.jp/product/hdd/network/ls-qvl_r5/
  - (ENG) http://www.buffalotech.com/products/network-storage/home-and-small-office/linkstation-pro-quadSigned-off-by: NMario Lange <mario_lange@gmx.net>
Signed-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

LS-WVL/VL are both kirkwood-6282 based NAS devices, which share
many MPP pins. However they are slightly different:
  - LS-WVL is 2-Bay NAS, and LS-VL is only 1-Bay.
  - There're two red LED indicator on LS-WVL to show when HDD fails,
    which is similar to LS-WXL, but there's no such on LS-VL.

So after the split, common part goes into .dtsi file:
  - kirkwood-linkstation-6282.dtsi
while all rest part goes into device specific .dts file:
  - kirkwood-linkstation-lsvl.dts
  - kirkwood-linkstation-lswvl.dts
Signed-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

LS-WXL/WSXL are both kirkwood-6281 based 2-Bay NAS devices, which share
many MPP pins. However they are slightly different:
  - There're two red LED indicator on LS-WXL to show when HDD fails,
    but there's no such on LS-WSXL.
  - There's 4-level speed adjustable FAN on LS-WXL, but not LS-WSXL.

So after the split, common part goes into .dtsi file:
  - kirkwood-linkstation.dtsi
  - kirkwood-linkstation-duo-6281.dtsi
while all rest part goes into device specific .dts file:
  - kirkwood-linkstation-lswsxl.dts
  - kirkwood-linkstation-lswxl.dts
Signed-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

This one is essentially the same as revision 2 B board (with the I2S on
P5 header).
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
[anholt: Rebased on bcm2835.dtsi -> bcm283x.dtsi change]
Signed-off-by: NEric Anholt <eric@anholt.net>

The Itead Ibox is a multi board device based on the Allwinner A20 SoC.
It contains the A20 Itead Core module and a base board for the external
interfaces.

The core module comes with 4GB NAND and 1GB DDR RAM.

The base board to which the core board is connected provides 3 USB 2.0 Host
ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet port, HDMI, IR receiver,
SPDIF and a 32-pin GPIO header. This header expands the features of core
board by exposing the VGA pins, audio In/Out pins, SATA, SPI, I2C, UARTS,
USB-OTG and power.
Signed-off-by: NMarcus Cooper <codekipper@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

It's device based on BCM47094 which is quite similar to BCM4709 except
for higher CPU frequency. This device has 2 flash memories, it boots
from serial one and stores firmware on NAND. Other than that we define
standard stuff like LEDs, buttons and UART.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Cubietruck Plus is a A83T/H8 based development board. The board has
standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host
via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet,
WiFi, headphone out / mic in, and various GPIO headers.

The board also has an EEPROM on i2c0 which holds the MAC address.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.

A83T patches are tested on this board.
It has UART, ethernet, USB, HDMI, etc ports on it.

For FEL mode it needs USB A-A(Male) cable. I used uart0 which
is multiplexed to microsd pins PF2 and PF4.

Enabled UART0 Header(PB9, PB10 pins).
Signed-off-by: NVishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Pi 2 B ends up like a Pi 1 B+, with the same peripherals and
pinout, but the CPU and memory layout changed to use the 2836.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This allows us to boot dra62x j5-eco evm with NFSroot.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This device tree was tested on a Sigma Designs SMP8758 Vantage-1172
Rev E1 development board.
Signed-off-by: NMarc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

SBC-iMX7 is a single board computer designed for industrial
and embedded applications. It is based on the Freescale i.MX7
system-on-chip. SBC-iMX7 is implemented with the CL-SOM-iMX7
System-on-Module providing most of the functions, and SB-SOM-iMX7
carrier board providing additional peripheral functions and
connectors.

http://www.compulab.co.il/products/sbcs/sbc-imx7-freescale-i-mx-7-single-board-computer/

http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/

Add basic board support, including SD card as a secondary boot and storage device
Signed-off-by: NIlya Ledvich <ilya@compulab.co.il>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>

CL-SOM-iMX7 is a miniature System-on-Module (SoM) based on
Freescale i.MX7 System-on-Chip family.

http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/

Add basic DT support for standalone module (without a carrier board):

* Memory configuration
* eMMC
* 2x Gigabit Ethernet ports (FEC1 and FEC2)
* I2C2 bus
  * EEPROM
  * PCA9555 GPIO extender
  * PMIC
* UART1
* USB OTG port
Signed-off-by: NIlya Ledvich <ilya@compulab.co.il>
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>

Novena is an open-hardware laptop/desktop/bare board.

See http://www.kosagi.com/w/index.php?title=Novena_Main_PageSigned-off-by: NSean Cross <xobs@kosagi.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This device tree adds support for TS-4800 by Technologic Systems. This
board is based on MX51-babbage, but there are some subtle differences in
the pins used, and there is an additional FPGA that is memory-mapped.

More details here:
  http://wiki.embeddedarm.com/wiki/TS-4800Signed-off-by: NDamien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>