Create the sections describing the McBSP ports to be able to use them via
DT.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Create the needed sections to be able to probe McBSP ports via DT.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Since the board is based on OMAP2420 we should include the dedicated dtsi
file (which includes the common omap2 dtsi).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

The McBSP IP within OMAP2420 and 2430 is different we need to create separate
dtsi files for them.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add the support for D6 and D7 LEDs on Beagle board.
- D6 will be used for heartbeat
- D7 will be used for mmc0
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add device tree properties for twl4030/gpio, according to the
platform data of corresponding boards. This enables the led
connected to LEDB output for both boards, as well as
pullups/pulldowns on GPIO for the BeagleBoard.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>

Remove some useless comment and move GIC controller outside
of the OCP node since it does use the MPU internal bus and
not the OCP.
This will not change the functionality but will reflect the
reality more accurately.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Add cortex-a9 local timer support for all OMAP4 based
SOCs using DT.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Provide PL310 Level 2 Cache Controller Device Tree
support for OMAP4 based devices.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Device tree data for the EMIF sdram controllers in OMAP4
and LPDDR2 memory devices attached to OMAP4 boards.
Reviewed-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NAneesh V <aneesh@ti.com>
[santosh.shilimkar@ti.com: Rebased against 3.6-rc]
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
[b-cousson@ti.com: Use label in board to access EMIF nodes]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add keypad data node in omap4 device tree file.
Also fill the device tree binding parameters
with the required value in "omap4-sdp" dts file.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
[b-cousson@ti.com: Re-align the entries and the comments]

Add bmp085 pressure sensor data in omap5 evm dts file.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add keypad data node in omap5 device tree file.
Also fill the device tree binding parameters
with the required value in "omap5-evm" dts file.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
[b-cousson@ti.com: Fix merge issue with MMC patches,
put node at the proper place, align entries and comments]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add tmp102 temperature sensor data in omap5 evm dts file.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add I2C data nodes in omap5 device tree file.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add tps65217 regulator device tree data to AM335x-Bone by adding
regulator consumers with tightened constraints and regulator-name.
TPS65217 regulator handle can be obtained by using this regulator
name.

This patch also add I2C node with I2C frequency and tps65217 PMIC
I2C slave address.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add tps65910 regulator device tree data to AM335x-EVM by adding
regulator consumers with tightened constraints and regulator-name.
TPS65910 regulator handle can be obtained by using this regulator
name.

This patch also add I2C node with I2C frequency and tps65910 PMIC
I2C slave address.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add device tree data for tps65217 regulator by adding all tps65217
regulator nodes. Regulator is initialized based on compatiable
name provided in tps65217 DT file.

All tps65910 PMIC regulator device tree nodes are placed in a
seperate device tree include file (tps65217.dtsi). This patch
was tested on AM335x-Bone.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add device tree data for tps65910 regulator by adding all tps65910
regulator nodes. Regulator is initialized based on compatiable
name provided in tps65910 DT file.

All tps65910 PMIC regulator device tree nodes are placed in a
seperate device tree include file (tps65910.dtsi). This patch
was tested on AM335x-EVM.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

regulators do not have a 'reg' property, hence the regulator@0,
regulator@1 do not make sense. get rid of it.
Reported-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Ideally in common SoC dtsi file should set all modules
to "disabled" state and it should get enabled in respective
EVM/Board dts file as per usage.

This patch sets default status of all modules to "disabled"
state in am33xx.dtsi file. Currently there are no modules
supported as part of Bone and EVM dts support, so care
to add entry "status = "okay"" while adding support for any
module.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add OMAP MMC related device tree data for OMAP5.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

vcxio, v2v1 and v1v8 are expected to be always on, update the dtsi
for twl6030 to reflect this.

commit '86f5fc' regulator: core: Mark all DT based boards as having
full constraints) caused these to be disabled at late boot causing
OMAP4 boards (using twl6030) to lockup.
Reported-by: NKishon Vijay Abraham I <kishon@ti.com>
Reported-by: NJ Keerthy <j-keerthy@ti.com>
Signed-off-by: NRajendra nayak <rnayak@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add am33xx wdt node.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
[tony@atomide.com: I messed up and produced an empty commit db27ac80 with stg apply]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add alias for gpio nodes, so that gpio driver can identify the port
number and then specify a sensible gpio base rather than using the
one dynamically allocated by gpio core.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Commit 88cde8b7 (ARM: dts: imx: update #interrupt-cells for gpio nodes)
changes gpio #interrupt-cells from 1 to 2 without updating the users.
It causes the gpio irq requesting call failing in client driver's probe
function.

Add the irq type cell for those gpio interrupt users to fix their
driver probe failure.
Reported-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Since commit c7e963f6 (net/smsc911x: Add regulator support), the lan9220
device tree probe fails on imx53-ard board, because the commit makes
VDD33A and VDDVARIO supplies mandatory for the driver.

Add a fixed dummy 3V3 supplying lan9220 to fix the regression.

Cc: stable@vger.kernel.org
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Fix registers range.

Cc: stable@vger.kernel.org
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Fix registers range.

Cc: stable@vger.kernel.org
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

In order to have audio functional on mx6qsabrelite, it is necessary
to setup the IOMUX for MX6Q_PAD_GPIO_0__CCM_CLKO pins as it provides
the audio clock.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Fix serial console node and allow the board to boot again.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

It has been decided to use marvell, not mrvl, in the compatibility
property. Search & replace.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJosh Coombs <josh.coombs@gmail.com>

Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Now that we have I2C support in DT, describe the LM63 in
the DT file for the iConnect.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>

Now that the GPIO controllers have been converted over to DT,
described the gpio-keys in DT.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NSimon Baatz <gmbnomis@gmail.com>

Move description of GPIO keys on both the DNS320 and DNS325 into DT.
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>