When building a kernel image with only CONFIG_CPU_IDLE but no CONFIG_PM,
we will get the following link error.

  LD      init/built-in.o
arch/arm/mach-imx/built-in.o: In function `imx6q_enter_wait':
platform-spi_imx.c:(.text+0x25c0): undefined reference to `imx6q_set_lpm'
platform-spi_imx.c:(.text+0x25d4): undefined reference to `imx6q_set_lpm'
arch/arm/mach-imx/built-in.o: In function `imx6q_cpuidle_init':
platform-spi_imx.c:(.init.text+0x75d4): undefined reference to `imx6q_set_chicken_bit'
make[1]: *** [vmlinux] Error 1

Since pm-imx6q.c has been a collection of library functions that access
CCM low-power registers used by not only suspend but also cpuidle and
other drivers, let's build pm-imx6q.c independently of CONFIG_PM to fix
above error.
Reported-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: stable@vger.kernel.org
Acked-by: NChristian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.14/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps, mostly to deal with the 34xx vs 36xx SoC
configuration for overo boards.

* tag 'omap-for-v3.14/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  Documentation: dt: OMAP: Update Overo/Tobi
  ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
  ARM: dts: omap3-tobi: Use the correct vendor prefix
  ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
  ARM: OMAP2+: Remove legacy macros for zoom platforms
  ARM: OMAP2+: Remove MACH_NOKIA_N800
  ARM: dts: N900: add missing compatible property
  ARM: dts: N9/N950: fix boot hang with 3.14-rc1
  ARM: OMAP1: nokia770: enable tahvo-usb
  ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
  ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
  ARM: dts: omap3-gta04: Fix mmc1 properties.
  ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
  ARM: OMAP2+: add missing ARCH_HAS_OPP
  ARM: dts: am335x-evmsk: Fix mmc1 support
  ARM: DTS: am335x-evmsk: Correct audio clock frequency
  ARM: dts: omap3-gta04: Add EOC irq gpio line handling.
Signed-off-by: NOlof Johansson <olof@lixom.net>

This alias entry was evidently cut/paste from a different board, and
not correctly updated to match Cardhu. Fix this.

Fixes: 553c0a20 ("ARM: tegra: set up /aliases entries for RTCs")
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'pwm_pxa_for_v3.14' of https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux into fixes

* tag 'pwm_pxa_for_v3.14' of https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux:
  ARM: pxa: Add dummy backlight power supply on Mitac Mio A701
Signed-off-by: NOlof Johansson <olof@lixom.net>

Pull btrfs fixes from Chris Mason:
 "We have a small collection of fixes in my for-linus branch.

  The big thing that stands out is a revert of a new ioctl.  Users
  haven't shipped yet in btrfs-progs, and Dave Sterba found a better way
  to export the information"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: use right clone root offset for compressed extents
  btrfs: fix null pointer deference at btrfs_sysfs_add_one+0x105
  Btrfs: unset DCACHE_DISCONNECTED when mounting default subvol
  Btrfs: fix max_inline mount option
  Btrfs: fix a lockdep warning when cleaning up aborted transaction
  Revert "btrfs: add ioctl to export size of global metadata reservation"

Pull devicetree fixes from Rob Herring:
 "Fix booting on PPC boards.  Changes to of_match_node matching caused
  the serial port on some PPC boards to stop working.  Reverted the
  change and reimplement to split matching between new style compatible
  only matching and fallback to old matching algorithm"

* tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: search the best compatible match first in __of_match_node()
  Revert "OF: base: match each node compatible against all given matches first"

Currently, of_match_node compares each given match against all node's
compatible strings with of_device_is_compatible.

To achieve multiple compatible strings per node with ordering from
specific to generic, this requires given matches to be ordered from
specific to generic. For most of the drivers this is not true and also
an alphabetical ordering is more sane there.

Therefore, this patch introduces a function to match each of the node's
compatible strings against all given compatible matches without type and
name first, before checking the next compatible string. This implies
that node's compatibles are ordered from specific to generic while
given matches can be in any order. If we fail to find such a match
entry, then fall-back to the old method in order to keep compatibility.

Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Tested-by: NStephen Chivers <schivers@csc.com>
Signed-off-by: NRob Herring <robh@kernel.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "Mostly minor fixes this time to v3.14-rc1 related changes.  Also
  included is one fix for a free after use regression in persistent
  reservations UNREGISTER logic that is CC'ed to >= v3.11.y stable"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  Target/sbc: Fix protection copy routine
  IB/srpt: replace strict_strtoul() with kstrtoul()
  target: Simplify command completion by removing CMD_T_FAILED flag
  iser-target: Fix leak on failure in isert_conn_create_fastreg_pool
  iscsi-target: Fix SNACK Type 1 + BegRun=0 handling
  target: Fix missing length check in spc_emulate_evpd_83()
  qla2xxx: Remove last vestiges of qla_tgt_cmd.cmd_list
  target: Fix 32-bit + CONFIG_LBDAF=n link error w/ sector_div
  target: Fix free-after-use regression in PR unregister

Pull i2c fixes from Wolfram Sang:
 "i2c has a bugfix and documentation improvements for you"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  Documentation: i2c: mention ACPI method for instantiating devices
  Documentation: i2c: describe devicetree method for instantiating devices
  i2c: mv64xxx: refactor message start to ensure proper initialization

Merge branches 'irq-urgent-for-linus' and 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq update from Thomas Gleixner:
 "Fix from the urgent branch: a trivial oneliner adding the missing
  Kconfig dependency curing build failures which have been discovered by
  several build robots.

  The update in the irq-core branch provides a new function in the
  irq/devres code, which is a prerequisite for driver developers to get
  rid of boilerplate code all over the place.

  Not a bugfix, but it has zero impact on the current kernel due to the
  lack of users.  It's simpler to provide the infrastructure to
  interested parties via your tree than fulfilling the wishlist of
  driver maintainers on which particular commit or tag this should be
  based on"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Add missing irq_to_desc export for CONFIG_SPARSE_IRQ=n

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq: Add devm_request_any_context_irq()

Pull timer fixes from Thomas Gleixner:
 "The following trilogy of patches brings you:

   - fix for a long standing math overflow issue with HZ < 60

   - an onliner fix for a corner case in the dreaded tick broadcast
     mechanism affecting a certain range of AMD machines which are
     infested with the infamous automagic C1E power control misfeature

   - a fix for one of the ARM platforms which allows the kernel to
     proceed and boot instead of stupidly panicing for no good reason.
     The patch is slightly larger than necessary, but it's less ugly
     than the alternative 5 liner"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick: Clear broadcast pending bit when switching to oneshot
  clocksource: Kona: Print warning rather than panic
  time: Fix overflow when HZ is smaller than 60

Merge tag 'trace-fixes-v3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull twi tracing fixes from Steven Rostedt:
 "Two urgent fixes in the tracing utility.

  The first is a fix for the way the ring buffer stores timestamps.
  After a restructure of the code was done, the ring buffer timestamp
  logic missed the fact that the first event on a sub buffer is to have
  a zero delta, as the full timestamp is stored on the sub buffer
  itself.  But because the delta was not cleared to zero, the timestamp
  for that event will be calculated as the real timestamp + the delta
  from the last timestamp.  This can skew the timestamps of the events
  and have them say they happened when they didn't really happen.
  That's bad.

  The second fix is for modifying the function graph caller site.  When
  the stop machine was removed from updating the function tracing code,
  it missed updating the function graph call site location.  It is still
  modified as if it is being done via stop machine.  But it's not.  This
  can lead to a GPF and kernel crash if the function graph call site
  happens to lie between cache lines and one CPU is executing it while
  another CPU is doing the update.  It would be a very hard condition to
  hit, but the result is severe enough to have it fixed ASAP"

* tag 'trace-fixes-v3.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace/x86: Use breakpoints for converting function graph caller
  ring-buffer: Fix first commit on sub-buffer having non-zero delta

Pull x86 EFI fixes from Peter Anvin:
 "A few more EFI-related fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/efi: Check status field to validate BGRT header
  x86/efi: Fix 32-bit fallout

Pull ARM SoC fixes from Kevin Hilman:
 "A collection of ARM SoC fixes for v3.14-rc1.

  Mostly a collection of Kconfig, device tree data and compilation fixes
  along with fix to drivers/phy that fixes a boot regression on some
  Marvell mvebu platforms"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  dma: mv_xor: Silence a bunch of LPAE-related warnings
  ARM: ux500: disable msp2 device tree node
  ARM: zynq: Reserve not DMAable space in front of the kernel
  ARM: multi_v7_defconfig: Select CONFIG_SOC_DRA7XX
  ARM: imx6: Initialize low-power mode early again
  ARM: pxa: fix various compilation problems
  ARM: pxa: fix compilation problem on AM300EPD board
  ARM: at91: add Atmel's SAMA5D3 Xplained board
  spi/atmel: document clock properties
  mmc: atmel-mci: document clock properties
  ARM: at91: enable USB host on at91sam9n12ek board
  ARM: at91/dt: fix sama5d3 ohci hclk clock reference
  ARM: at91/dt: sam9263: fix compatibility string for the I2C
  ata: sata_mv: Fix probe failures with optional phys
  drivers: phy: Add support for optional phys
  drivers: phy: Make NULL a valid phy reference
  ARM: fix HAVE_ARM_TWD selection for OMAP and shmobile
  ARM: moxart: move DMA_OF selection to driver
  ARM: hisi: fix kconfig warning on HAVE_ARM_TWD

Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NGuenter Roeck <linux@roeck-us.net>

Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

For non compressed extents, iterate_extent_inodes() gives us offsets
that take into account the data offset from the file extent items, while
for compressed extents it doesn't. Therefore we have to adjust them before
placing them in a send clone instruction. Not doing this adjustment leads to
the receiving end requesting for a wrong a file range to the clone ioctl,
which results in different file content from the one in the original send
root.

Issue reproducible with the following excerpt from the test I made for
xfstests:

  _scratch_mkfs
  _scratch_mount "-o compress-force=lzo"

  $XFS_IO_PROG -f -c "truncate 118811" $SCRATCH_MNT/foo
  $XFS_IO_PROG -c "pwrite -S 0x0d -b 39987 92267 39987" $SCRATCH_MNT/foo

  $BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/mysnap1

  $XFS_IO_PROG -c "pwrite -S 0x3e -b 80000 200000 80000" $SCRATCH_MNT/foo
  $BTRFS_UTIL_PROG filesystem sync $SCRATCH_MNT
  $XFS_IO_PROG -c "pwrite -S 0xdc -b 10000 250000 10000" $SCRATCH_MNT/foo
  $XFS_IO_PROG -c "pwrite -S 0xff -b 10000 300000 10000" $SCRATCH_MNT/foo

  # will be used for incremental send to be able to issue clone operations
  $BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/clones_snap

  $BTRFS_UTIL_PROG subvolume snapshot -r $SCRATCH_MNT $SCRATCH_MNT/mysnap2

  $FSSUM_PROG -A -f -w $tmp/1.fssum $SCRATCH_MNT/mysnap1
  $FSSUM_PROG -A -f -w $tmp/2.fssum -x $SCRATCH_MNT/mysnap2/mysnap1 \
      -x $SCRATCH_MNT/mysnap2/clones_snap $SCRATCH_MNT/mysnap2
  $FSSUM_PROG -A -f -w $tmp/clones.fssum $SCRATCH_MNT/clones_snap \
      -x $SCRATCH_MNT/clones_snap/mysnap1 -x $SCRATCH_MNT/clones_snap/mysnap2

  $BTRFS_UTIL_PROG send $SCRATCH_MNT/mysnap1 -f $tmp/1.snap
  $BTRFS_UTIL_PROG send $SCRATCH_MNT/clones_snap -f $tmp/clones.snap
  $BTRFS_UTIL_PROG send -p $SCRATCH_MNT/mysnap1 \
      -c $SCRATCH_MNT/clones_snap $SCRATCH_MNT/mysnap2 -f $tmp/2.snap

  _scratch_unmount
  _scratch_mkfs
  _scratch_mount

  $BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/1.snap
  $FSSUM_PROG -r $tmp/1.fssum $SCRATCH_MNT/mysnap1 2>> $seqres.full

  $BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/clones.snap
  $FSSUM_PROG -r $tmp/clones.fssum $SCRATCH_MNT/clones_snap 2>> $seqres.full

  $BTRFS_UTIL_PROG receive $SCRATCH_MNT -f $tmp/2.snap
  $FSSUM_PROG -r $tmp/2.fssum $SCRATCH_MNT/mysnap2 2>> $seqres.full
Signed-off-by: NFilipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: NChris Mason <clm@fb.com>

bdev is null when disk has disappeared and mounted with
the degrade option

stack trace
---------
btrfs_sysfs_add_one+0x105/0x1c0 [btrfs]
open_ctree+0x15f3/0x1fe0 [btrfs]
btrfs_mount+0x5db/0x790 [btrfs]
? alloc_pages_current+0xa4/0x160
mount_fs+0x34/0x1b0
vfs_kern_mount+0x62/0xf0
do_mount+0x22e/0xa80
? __get_free_pages+0x9/0x40
? copy_mount_options+0x31/0x170
SyS_mount+0x7e/0xc0
system_call_fastpath+0x16/0x1b
---------

reproducer:
-------
mkfs.btrfs -draid1 -mraid1 /dev/sdc /dev/sdd
(detach a disk)
devmgt detach /dev/sdc [1]
mount -o degrade /dev/sdd /btrfs
-------

[1] github.com/anajain/devmgt.git
Signed-off-by: NAnand Jain <Anand.Jain@oracle.com>
Tested-by: NHidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: NChris Mason <clm@fb.com>

Because the offload mechanism can fall back to a standard transfer,
having two seperate initialization states is unfortunate. Let's just
have one state which does things consistently. This fixes a bug where
some preparation was missing when the fallback happened. And it makes
the code much easier to follow. To implement this, we put the check
if offload is possible at the top of the offload setup function.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Tested-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d4 (i2c: mv64xxx: Add I2C Transaction Generator support)

Pull USB fixes from Greg KH:
 "Here is a bunch of USB fixes for 3.14-rc3.  Most of these are xhci
  reverts, fixing a bunch of reported issues with USB 3 host controller
  issues that loads of people have been hitting (with the exception of
  kernel developers, all of our machines seem to be working fine, which
  is why these took so long to get resolved...)

  There are some other minor fixes and new device ids, as ususal.  All
  have been in linux-next successfully"

* tag 'usb-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
  usb: option: blacklist ZTE MF667 net interface
  Revert "usb: xhci: Link TRB must not occur within a USB payload burst"
  Revert "xhci: Avoid infinite loop when sg urb requires too many trbs"
  Revert "xhci: Set scatter-gather limit to avoid failed block writes."
  xhci 1.0: Limit arbitrarily-aligned scatter gather.
  Modpost: fixed USB alias generation for ranges including 0x9 and 0xA
  usb: core: Fix potential memory leak adding dyn USBdevice IDs
  USB: ftdi_sio: add Tagsys RFID Reader IDs
  usb: qcserial: add Netgear Aircard 340U
  usb-storage: enable multi-LUN scanning when needed
  USB: simple: add Dynastream ANT USB-m Stick device support
  usb-storage: add unusual-devs entry for BlackBerry 9000
  usb-storage: restrict bcdDevice range for Super Top in Cypress ATACB
  usb: phy: move some error messages to debug
  usb: ftdi_sio: add Mindstorms EV3 console adapter
  usb: dwc2: fix memory corruption in dwc2 driver
  usb: dwc2: fix role switch breakage
  usb: dwc2: bail out early when booting with "nousb"
  Revert "xhci: replace xhci_read_64() with readq()"
  Revert "xhci: replace xhci_write_64() with writeq()"
  ...

Pull tty/serial driver fixes from Greg KH:
 "Here are a small number of tty/serial driver fixes to resolve reported
  issues with 3.14-rc and earlier (in the case of the vt bugfix).  Some
  of these have been tested and reported by a number of people as the
  tty bugfix was pretty commonly hit on some platforms.

  All have been in linux-next for a while"

* tag 'tty-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  vt: Fix secure clear screen
  serial: 8250: Support XR17V35x fraction divisor
  n_tty: Fix stale echo output
  serial: sirf: fix kernel panic caused by unpaired spinlock
  serial: 8250_pci: unbreak last serial ports on NetMos 9865 cards
  n_tty: Fix poll() when TIME_CHAR and MIN_CHAR == 0
  serial: omap: fix rs485 probe on defered pinctrl
  serial: 8250_dw: fix compilation warning when !CONFIG_PM_SLEEP
  serial: omap-serial: Move info message to probe function
  tty: Set correct tty name in 'active' sysfs attribute
  tty: n_gsm: Fix for modems with brk in modem status control
  drivers/tty/hvc: don't use module_init in non-modular hyp. console code

Pull staging driver fixes from Greg KH:
 "Here are a number (lots, I know) of fixes for staging drivers to
  resolve a bunch of reported issues.

  The largest patches here is one revert of a patch that is in 3.14-rc1
  to fix reported problems, and a sync of a usb host driver that
  required some ARM patches to go in before it could be accepted (which
  is why it missed -rc1)

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (56 commits)
  staging/rtl8821ae: fix build, depends on MAC80211
  iio: max1363: Use devm_regulator_get_optional for optional regulator
  iio:accel:bma180: Use modifier instead of index in channel specification
  iio: adis16400: Set timestamp as the last element in chan_spec
  iio: ak8975: Fix calculation formula for convert micro tesla to gauss unit
  staging:iio:ad799x fix typo in ad799x_events[]
  iio: mxs-lradc: remove useless scale_available files
  iio: mxs-lradc: fix buffer overflow
  iio:magnetometer:mag3110: Fix output of decimal digits in show_int_plus_micros()
  iio:magnetometer:mag3110: Report busy in _read_raw() / write_raw() when buffer is enabled
  wlags49_h2: Fix overflow in wireless_set_essid()
  xlr_net: Fix missing trivial allocation check
  staging: r8188eu: overflow in rtw_p2p_get_go_device_address()
  staging: r8188eu: array overflow in rtw_mp_ioctl_hdl()
  staging: r8188eu: Fix typo in USB_DEVICE list
  usbip/userspace/libsrc/names.c: memory leak
  gpu: ion: dereferencing an ERR_PTR
  staging: comedi: usbduxsigma: fix unaligned dereferences
  staging: comedi: fix too early cleanup in comedi_auto_config()
  staging: android: ion: dummy: fix an error code
  ...

Merge tag 'driver-core-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg KH:
 "Here is a single driver core patch for 3.14-rc3 for the component code
  that Russell has found and fixed"

* tag 'driver-core-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  drivers/base: fix devres handling for master device

Pull char/misc fixes from Greg KH:
 "Here are some small char/misc driver fixes, along with some
  documentation updates, for 3.14-rc3.  Nothing major, just a number of
  fixes for reported issues"

* tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Revert "misc: eeprom: sunxi: Add new compatibles"
  Revert "ARM: sunxi: dt: Convert to the new SID compatibles"
  misc: mic: fix possible signed underflow (undefined behavior) in userspace API
  ARM: sunxi: dt: Convert to the new SID compatibles
  misc: eeprom: sunxi: Add new compatibles
  misc: genwqe: Fix potential memory leak when pinning memory
  Documentation:Update Documentation/zh_CN/arm64/memory.txt
  Documentation:Update Documentation/zh_CN/arm64/booting.txt
  Documentation:Chinese translation of Documentation/arm64/tagged-pointers.txt
  raw: set range for MAX_RAW_DEVS
  raw: test against runtime value of max_raw_minors
  Drivers: hv: vmbus: Don't timeout during the initial connection with host
  Drivers: hv: vmbus: Specify the target CPU that should receive notification
  VME: Correct read/write alignment algorithm
  mei: don't unset read cb ptr on reset
  mei: clear write cb from waiting list on reset

A user was running into errors from an NFS export of a subvolume that had a
default subvol set.  When we mount a default subvol we will use d_obtain_alias()
to find an existing dentry for the subvolume in the case that the root subvol
has already been mounted, or a dummy one is allocated in the case that the root
subvol has not already been mounted.  This allows us to connect the dentry later
on if we wander into the path.  However if we don't ever wander into the path we
will keep DCACHE_DISCONNECTED set for a long time, which angers NFS.  It doesn't
appear to cause any problems but it is annoying nonetheless, so simply unset
DCACHE_DISCONNECTED in the get_default_root case and switch btrfs_lookup() to
use d_materialise_unique() instead which will make everything play nicely
together and reconnect stuff if we wander into the defaul subvol path from a
different way.  With this patch I'm no longer getting the NFS errors when
exporting a volume that has been mounted with a default subvol set.  Thanks,

cc: bfields@fieldses.org
cc: ebiederm@xmission.com
Signed-off-by: NJosef Bacik <jbacik@fb.com>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NChris Mason <clm@fb.com>

Currently, the only mount option for max_inline that has any effect is
max_inline=0.  Any other value that is supplied to max_inline will be
adjusted to a minimum of 4k.  Since max_inline has an effective maximum
of ~3900 bytes due to page size limitations, the current behaviour
only has meaning for max_inline=0.

This patch will allow the the max_inline mount option to accept non-zero
values as indicated in the documentation.
Signed-off-by: NMitch Harder <mitch.harder@sabayonlinux.org>
Signed-off-by: NChris Mason <clm@fb.com>

Given now we have 2 spinlock for management of delayed refs,
CONFIG_DEBUG_SPINLOCK=y helped me find this,

[ 4723.413809] BUG: spinlock wrong CPU on CPU#1, btrfs-transacti/2258
[ 4723.414882]  lock: 0xffff880048377670, .magic: dead4ead, .owner: btrfs-transacti/2258, .owner_cpu: 2
[ 4723.417146] CPU: 1 PID: 2258 Comm: btrfs-transacti Tainted: G        W  O 3.12.0+ #4
[ 4723.421321] Call Trace:
[ 4723.421872]  [<ffffffff81680fe7>] dump_stack+0x54/0x74
[ 4723.422753]  [<ffffffff81681093>] spin_dump+0x8c/0x91
[ 4723.424979]  [<ffffffff816810b9>] spin_bug+0x21/0x26
[ 4723.425846]  [<ffffffff81323956>] do_raw_spin_unlock+0x66/0x90
[ 4723.434424]  [<ffffffff81689bf7>] _raw_spin_unlock+0x27/0x40
[ 4723.438747]  [<ffffffffa015da9e>] btrfs_cleanup_one_transaction+0x35e/0x710 [btrfs]
[ 4723.443321]  [<ffffffffa015df54>] btrfs_cleanup_transaction+0x104/0x570 [btrfs]
[ 4723.444692]  [<ffffffff810c1b5d>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[ 4723.450336]  [<ffffffff810c1c2d>] ? trace_hardirqs_on+0xd/0x10
[ 4723.451332]  [<ffffffffa015e5ee>] transaction_kthread+0x22e/0x270 [btrfs]
[ 4723.452543]  [<ffffffffa015e3c0>] ? btrfs_cleanup_transaction+0x570/0x570 [btrfs]
[ 4723.457833]  [<ffffffff81079efa>] kthread+0xea/0xf0
[ 4723.458990]  [<ffffffff81079e10>] ? kthread_create_on_node+0x140/0x140
[ 4723.460133]  [<ffffffff81692aac>] ret_from_fork+0x7c/0xb0
[ 4723.460865]  [<ffffffff81079e10>] ? kthread_create_on_node+0x140/0x140
[ 4723.496521] ------------[ cut here ]------------

----------------------------------------------------------------------

The reason is that we get to call cond_resched_lock(&head_ref->lock) while
still holding @delayed_refs->lock.

So it's different with __btrfs_run_delayed_refs(), where we do drop-acquire
dance before and after actually processing delayed refs.

Here we don't drop the lock, others are not able to add new delayed refs to
head_ref, so cond_resched_lock(&head_ref->lock) is not necessary here.
Signed-off-by: NLiu Bo <bo.li.liu@oracle.com>
Signed-off-by: NChris Mason <clm@fb.com>

This reverts commit 01e219e8.

David Sterba found a different way to provide these features without adding a new
ioctl.  We haven't released any progs with this ioctl yet, so I'm taking this out
for now until we finalize things.
Signed-off-by: NChris Mason <clm@fb.com>
Signed-off-by: NDavid Sterba <dsterba@suse.cz>
CC: Jeff Mahoney <jeffm@suse.com>

Pull two nfsd bugfixes from Bruce Fields.

* 'for-3.14' of git://linux-nfs.org/~bfields/linux:
  lockd: send correct lock when granting a delayed lock.
  nfsd4: fix acl buffer overrun

Pull md fixes from Neil Brown:
 "Two bugfixes for md

  both tagged for -stable"

* tag 'md/3.14-fixes' of git://neil.brown.name/md:
  md/raid5: Fix CPU hotplug callback registration
  md/raid1: restore ability for check and repair to fix read errors.

This reverts commit 10535314.
Stephen Chivers reported this is broken as we will get a match
entry '.type = "serial"' instead of the '.compatible = "ns16550"'
in the following scenario:
	serial0: serial@4500 {
		compatible = "fsl,ns16550", "ns16550";
	}

	struct of_device_id of_platform_serial_table[] = {
		{ .compatible = "ns8250",   .data = (void *)PORT_8250, },
		{ .compatible = "ns16450",  .data = (void *)PORT_16450, },
		{ .compatible = "ns16550a", .data = (void *)PORT_16550A, },
		{ .compatible = "ns16550",  .data = (void *)PORT_16550, },
		{ .compatible = "ns16750",  .data = (void *)PORT_16750, },
		{ .compatible = "ns16850",  .data = (void *)PORT_16850, },
		...
		{ .type = "serial",         .data = (void *)PORT_UNKNOWN, },
		{ /* end of list */ },
	};

So just revert this patch, we will use another implementation to find
the best compatible match in a follow-on patch.
Reported-by: NStephen N Chivers <schivers@csc.com.au>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NRob Herring <robh@kernel.org>

This reverts commit f0de8e04, it is
incorrect, a future patch will fix this up properly.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 01ab1167, it is
incorrect, a future patch will fix this up properly.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There have been reports of EFI crashes since -rc1. The following two
commits fix known issues.

 * Fix boot failure on 32-bit EFI due to the recent EFI memmap changes
   merged during the merge window - Borislav Petkov

 * Avoid a crash during efi_bgrt_init() by detecting invalid BGRT
   headers based on the 'status' field.
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Pull KVM fixes from Paolo Bonzini:
 "A small error handling problem and a compile breakage for ARM64"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  arm64: KVM: Add VGIC device control for arm64
  KVM: return an error code in kvm_vm_ioctl_register_coalesced_mmio()

Pull x86 fixes from Peter Anvin:
 "A collection of small fixes:

   - There still seem to be problems with asm goto which requires the
     empty asm hack.
   - If SMAP is disabled at compile time, don't enable it nor try to
     interpret a page fault as an SMAP violation.
   - Fix a case of unbounded recursion while tracing"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, smap: smap_violation() is bogus if CONFIG_X86_SMAP is off
  x86, smap: Don't enable SMAP if CONFIG_X86_SMAP is disabled
  compiler/gcc4: Make quirk for asm_volatile_goto() unconditional
  x86: Use preempt_disable_notrace() in cycles_2_ns()

Pull ACPI and power management fixes from Rafael Wysocki:
 "These include a fix for a recent intel_pstate regression, a fix for a
  regression in the ACPI-based PCI hotplug (ACPIPHP) code introduced
  during the 3.12 cycle, fixes for two bugs in the ACPI core introduced
  recently and a MAINTAINERS update related to cpufreq.

  Specifics:

   - Fix for a recent regression in the intel_pstate driver that
     introduced a race condition causing systems to crash during
     initialization in some situations.  This removes the affected code
     altogether.  From Dirk Brandewie.

   - ACPIPHP fix for a regression introduced during the 3.12 cycle
     causing devices to be dropped as a result of bus check
     notifications after system resume on some systems due to the way
     ACPIPHP interprets _STA return values (arguably incorrectly).  From
     Mika Westerberg.

   - ACPI dock driver fix for a problem causing docking to fail due to a
     check that always fails after recent ACPI core changes (found by
     code inspection).

   - ACPI container driver fix to prevent memory from being leaked in an
     error code path after device_register() failures.

   - Update of the arm_big_little cpufreq driver maintainer's e-mail
     address"

* tag 'pm+acpi-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  MAINTAINERS / cpufreq: update Sudeep's email address
  intel_pstate: Remove energy reporting from pstate_sample tracepoint
  ACPI / container: Fix error code path in container_device_attach()
  ACPI / hotplug / PCI: Relax the checking of _STA return values
  ACPI / dock: Use acpi_device_enumerated() to check if dock is present

Pull EDAC fixes from Borislav Petkov:
 "Fix polling timeout setting through sysfs.

  You're surely wondering why the patches are not based on an rc.  Well,
  Andrew sent you 79040cad ("drivers/edac/edac_mc_sysfs.c: poll
  timeout cannot be zero sent you") already (it got in in -rc2) but it
  is not enough as a fix because for one, setting too low polling
  intervals (< 1sec) don't make any sense and cause unnecessary polling
  load on the system.

  Then, even if we set some interval, we explode with

    [ 4143.094342] WARNING: CPU: 1 PID: 0 at kernel/workqueue.c:1393 __queue_work+0x1d7/0x340()

  because the workqueue setup path is used also for the timeout period
  resetting and we're doing INIT_DELAYED_WORK() on an already active
  workqueue.  Which is total bollocks.  So this is taken care of by the
  second patch.

  I've CCed stable for those two"

* tag 'edac_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  EDAC: Correct workqueue setup path
  EDAC: Poll timeout cannot be zero, p2

Pull fbdev fixes from Tomi Valkeinen:
 "Minor fbdev fixes for 3.14"

* tag 'fbdev-fixes-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
  video: Kconfig: Allow more broad selection of the imxfb framebuffer driver.
  video: exynos: Fix S6E8AX0 LCD driver build error
  OMAPDSS: fix fck field types
  OMAPDSS: DISPC: decimation rounding fix