If relocate of block group 0 fails with ENOSPC we end up infinitely
looping because key.offset -= 1 statement in that case brings us back to
where we started.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Generally we don't allow dup for data, but mixed chunks are special and
people seem to think this has its use cases.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Do not run sanity checks on all target profiles unless they all will be
used.  This came up because alloc_profile_is_valid() is now more strict
than it used to be.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Header file is not a good place to define functions.  This also moves a
call to alloc_profile_is_valid() down the stack and removes a redundant
check from __btrfs_alloc_chunk() - alloc_profile_is_valid() takes it
into account.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

"0" is a valid value for an on-disk chunk profile, but it is not a valid
extended profile.  (We have a separate bit for single chunks in extended
case)

Also rename it to alloc_profile_is_valid() for clarity.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Add functions to abstract the conversion between chunk and extended
allocation profile formats and switch everybody to use them.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

A few years ago the btrfs code to support blocks lager than
the page size was disabled to fix a few corner cases in the
page cache handling.  This fixes the code to properly support
large metadata blocks again.

Since current kernels will crash early and often with larger
metadata blocks, this adds an incompat bit so that older kernels
can't mount it.

This also does away with different blocksizes for nodes and leaves.
You get a single block size for all tree blocks.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

When we are setting up the mount, we close all the
devices that were not actually part of the metadata we found.

But, we don't make sure that one of those devices wasn't
fs_devices->latest_bdev, which means we can do a use after free
on the one we closed.

This updates latest_bdev as it goes.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

This patch corrects error checking of lookup_extent_mapping().
Signed-off-by: NTsutomu Itoh <t-itoh@jp.fujitsu.com>

Raid array setup code creates an extent buffer in an usual way. When the
PAGE_CACHE_SIZE is > super block size, the extent pages are not marked
up-to-date, which triggers a WARN_ON in the following
write_extent_buffer call. Add an explicit up-to-date call to silence the
warning.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>

system chunks by default are very small.  This makes them slightly
larger and also fixes the conditional checks to make sure we don't
allocate a billion of them at once.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Implement an ioctl for canceling restriper.  Currently we wait until
relocation of the current block group is finished, in future this can be
done by triggering a commit.  Balance item is deleted and no memory
about the interrupted balance is kept.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Implement an ioctl for pausing restriper.  This pauses the relocation,
but balance is still considered to be "in progress": balance item is
not deleted, other volume operations cannot be started, etc.  If paused
in the middle of profile changing operation we will continue making
allocations with the target profile.

Add a hook to close_ctree() to pause restriper and free its data
structures on unmount.  (It's safe to unmount when restriper is in
"paused" state, we will resume with the same parameters on the next
mount)
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Since restriper kthread starts involuntarily on mount and can suck cpu
and memory bandwidth add a mount option to forcefully skip it.  The
restriper in that case hangs around in paused state and can be resumed
from userspace when it's convenient.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

On mount, if balance item is found, resume balance in a separate
kernel thread.

Try to be smart to continue roughly where previous balance (or convert)
was interrupted.  For chunk types that were being converted to some
profile we turn on soft convert, in case of a simple balance we turn on
usage filter and relocate only less-than-90%-full chunks of that type.
These are just heuristics but they help quite a bit, and can be improved
in future.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Introduce a new btree objectid for storing balance item.  The reason is
to be able to resume restriper after a crash with the same parameters.
Balance item has a very high objectid and goes into tree of tree roots.

The key for the new item is as follows:

	[ BTRFS_BALANCE_OBJECTID ; BTRFS_BALANCE_ITEM_KEY ; 0 ]

Older kernels simply ignore it so it's safe to mount with an older
kernel and then go back to the newer one.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

When doing convert from one profile to another if soft mode is on
restriper won't touch chunks that already have the profile we are
converting to.  This is useful if e.g. half of the FS was converted
earlier.

The soft mode switch is (like every other filter) per-type.  This means
that we can convert for example meta chunks the "hard" way while
converting data chunks selectively with soft switch.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Profile changing is done by launching a balance with
BTRFS_BALANCE_CONVERT bits set and target fields of respective
btrfs_balance_args structs initialized.  Profile reducing code in this
case will pick restriper's target profile if it's available instead of
doing a blind reduce.  If target profile is not yet available it goes
back to a plain reduce.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Select chunks which have at least one byte located inside a given
[vstart, vend) virtual address space range.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Select chunks which have at least one byte of at least one stripe
located on a device with devid X in a given [pstart,pend) physical
address range.

This filter only works when devid filter is turned on.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Relocate chunks which have at least one stripe located on a device with
devid X.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Select chunks that are less than X percent full.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Select chunks based on a given profile mask.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

This allows to have a separate set of filters for each chunk type
(data,meta,sys).  The code however is generic and switch on chunk type
is only done once.

This commit also adds a type filter: it allows to balance for example
meta and system chunks w/o touching data ones.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Add basic restriper infrastructure: extended balancing ioctl and all
related ioctl data structures, add data structure for tracking
restriper's state to fs_info, etc.  The semantics of the old balancing
ioctl are fully preserved.

Explicitly disallow any volume operations when balance is in progress.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

Chunk's type and profile are encoded in u64 flags field.  Introduce
masks to easily access them.  Also fix the type of BTRFS_BLOCK_GROUP_*
constants, it should be ULL.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

{data,metadata,system}_alloc_profile fields have been unused for a long
time now.  Get rid of them.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>

The correct lock order is uuid_mutex -> volume_mutex -> chunk_mutex,
but when we mount a filesystem which has backing seed devices, we have
this lock chain:

    open_ctree()
        lock(chunk_mutex);
        read_chunk_tree();
            read_one_dev();
                open_seed_devices();
                    lock(uuid_mutex);

and then we hit a lockdep splat.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>

For btrfs raid, while discarding a range of space, we'll need to know
the start offset and length to discard for each device, and it's done
in btrfs_map_block().

However the calculation is a bit complex for raid0 and raid10, so I
reimplement it based on a fact that:

        dev1          dev2           dev3    (raid0)
        -----------------------------------
        s0 s3 s6      s1 s4 s7       s2 s5

Each device has (total_stripes / nr_dev) stripes, or plus one.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>

We pre-allocate a btrfs bio with fixed size, and then may re-allocate
memory if we find stripes are bigger than the fixed size. But this
pre-allocation is not necessary.

Also we don't have to calcuate the stripe number twice.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>

Some functions never use the transaction handle passed to them.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>

pathname resolution under a global mutex, taken on some paths in ->mount()
is a Bad Idea(tm) - think what happens if said pathname resolution triggers
automount of some btrfs instance and walks into attempt to grab the same
mutex.  Deadlock - we are waiting for daemon to finish walking the path,
daemon is waiting for us to release the mutex...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The 256MB chunk is a little small on a huge FS.  This scales up the
chunk size.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

This is the last part of the patch series. It modifies the btrfs
code to use the integrity check module if configured to do so
with the define BTRFS_FS_CHECK_INTEGRITY. If this define is not set,
the only effective change is that code is added that handles the
mount option to activate the integrity check. If the mount option is
set and the define BTRFS_FS_CHECK_INTEGRITY is not set, that code
complains in the log and the mount fails with EINVAL.

Add the mount option to activate the usage of the integrity check
code.
Add invocation of btrfs integrity check code init and cleanup
function on mount and umount, respectively.
Add hook to call btrfs integrity check code version of
submit_bh/submit_bio.
Signed-off-by: NStefan Behrens <sbehrens@giantdisaster.de>

The btrfs io submission threads can build up massive plug lists.  This
keeps things more reasonable so we don't hand over huge dumps of IO at
once.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

btrfs_end_bio checks the number of errors on a bio against the max
number of errors allowed before sending any EIOs up to the higher
levels.

If we got enough copies of the bio done for a given raid level, it is
supposed to clear the bio error flag and return success.

We have pointers to the original bio sent down by the higher layers and
pointers to any cloned bios we made for raid purposes.  If the original
bio happens to be the one that got an io error, but not the last one to
finish, it might not have the BIO_UPTODATE bit set.

Then, when the last bio does finish, we'll call bio_end_io on the
original bio.  It won't have the uptodate bit set and we'll end up
sending EIO to the higher layers.

We already had a check for this, it just was conditional on getting the
IO error on the very last bio.  Make the check unconditional so we eat
the EIOs properly.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

If we call ioctl(BTRFS_IOC_ADD_DEV) directly, we'll succeed in adding
a readonly device to a btrfs filesystem, and btrfs will write to
that device, emitting kernel errors:

[ 3109.833692] lost page write due to I/O error on loop2
[ 3109.833720] lost page write due to I/O error on loop2
...
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

btrfs_previous_item() just search the b+ tree, do not COW the nodes or leaves,
if we modify the result of it, the meta-data will be broken. fix it.
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Signed-off-by: NChris Mason <chris.mason@oracle.com>

fs_info has now ~9kb, more than fits into one page. This will cause
mount failure when memory is too fragmented. Top space consumers are
super block structures super_copy and super_for_commit, ~2.8kb each.
Allocate them dynamically. fs_info will be ~3.5kb. (measured on x86_64)

Add a wrapper for freeing fs_info and all of it's dynamically allocated
members.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>