- 25 4月, 2012 1 次提交
-
-
由 Eliad Peller 提交于
ieee80211_mgd_teardown() is called on netdev removal, which occurs after the vif was already removed from the low-level driver, resulting in the following warning: [ 4809.014734] ------------[ cut here ]------------ [ 4809.019861] WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211]() [ 4809.030388] wlan0: Failed check-sdata-in-driver check, flags: 0x4 [ 4809.036862] Modules linked in: wlcore_sdio(-) wl12xx wlcore mac80211 cfg80211 [last unloaded: cfg80211] [ 4809.046849] [<c001bd4c>] (unwind_backtrace+0x0/0x12c) [ 4809.055937] [<c047cf1c>] (dump_stack+0x20/0x24) [ 4809.065385] [<c003e334>] (warn_slowpath_common+0x5c/0x74) [ 4809.075589] [<c003e408>] (warn_slowpath_fmt+0x40/0x48) [ 4809.088291] [<bf033630>] (ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211]) [ 4809.102844] [<bf067f84>] (ieee80211_destroy_auth_data+0x80/0xa4 [mac80211]) [ 4809.116276] [<bf068004>] (ieee80211_mgd_teardown+0x5c/0x74 [mac80211]) [ 4809.129331] [<bf043f18>] (ieee80211_teardown_sdata+0xb0/0xd8 [mac80211]) [ 4809.141595] [<c03b5e58>] (rollback_registered_many+0x228/0x2f0) [ 4809.153056] [<c03b5f48>] (unregister_netdevice_many+0x28/0x50) [ 4809.165696] [<bf041ea8>] (ieee80211_remove_interfaces+0xb4/0xdc [mac80211]) [ 4809.179151] [<bf032174>] (ieee80211_unregister_hw+0x50/0xf0 [mac80211]) [ 4809.191043] [<bf0bebb4>] (wlcore_remove+0x5c/0x7c [wlcore]) [ 4809.201491] [<c02c6918>] (platform_drv_remove+0x24/0x28) [ 4809.212029] [<c02c4d50>] (__device_release_driver+0x8c/0xcc) [ 4809.222738] [<c02c4e84>] (device_release_driver+0x30/0x3c) [ 4809.233099] [<c02c4258>] (bus_remove_device+0x10c/0x128) [ 4809.242620] [<c02c26f8>] (device_del+0x11c/0x17c) [ 4809.252150] [<c02c6de0>] (platform_device_del+0x28/0x68) [ 4809.263051] [<bf0df49c>] (wl1271_remove+0x3c/0x50 [wlcore_sdio]) [ 4809.273590] [<c03806b0>] (sdio_bus_remove+0x48/0xf8) [ 4809.283754] [<c02c4d50>] (__device_release_driver+0x8c/0xcc) [ 4809.293729] [<c02c4e2c>] (driver_detach+0x9c/0xc4) [ 4809.303163] [<c02c3d7c>] (bus_remove_driver+0xc4/0xf4) [ 4809.312973] [<c02c5a98>] (driver_unregister+0x70/0x7c) [ 4809.323220] [<c03809c4>] (sdio_unregister_driver+0x24/0x2c) [ 4809.334213] [<bf0df458>] (wl1271_exit+0x14/0x1c [wlcore_sdio]) [ 4809.344930] [<c009b1a4>] (sys_delete_module+0x228/0x2a8) [ 4809.354734] ---[ end trace 515290ccf5feb522 ]--- Rename ieee80211_mgd_teardown() to ieee80211_mgd_stop(), and call it on ieee80211_do_stop(). Signed-off-by: NEliad Peller <eliad@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 24 4月, 2012 1 次提交
-
-
由 Peter Huang (Peng) 提交于
bridge: set fake_rtable's dst to NULL to avoid kernel Oops when bridge is deleted before tap/vif device's delete, kernel may encounter an oops because of NULL reference to fake_rtable's dst. Set fake_rtable's dst to NULL before sending packets out can solve this problem. v4 reformat, change br_drop_fake_rtable(skb) to {} v3 enrich commit header v2 introducing new flag DST_FAKE_RTABLE to dst_entry struct. [ Use "do { } while (0)" for nop br_drop_fake_rtable() implementation -DaveM ] Acked-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NPeter Huang <peter.huangpeng@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 4月, 2012 1 次提交
-
-
由 Neal Cardwell 提交于
Commit f5fff5dc forgot to fix TCP_MAXSEG behavior IPv6 sockets, so IPv6 TCP server sockets that used TCP_MAXSEG would find that the advmss of child sockets would be incorrect. This commit mirrors the advmss logic from tcp_v4_syn_recv_sock in tcp_v6_syn_recv_sock. Eventually this logic should probably be shared between IPv4 and IPv6, but this at least fixes this issue. Signed-off-by: NNeal Cardwell <ncardwell@google.com> Acked-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 4月, 2012 1 次提交
-
-
由 Eric Dumazet 提交于
It seems there is a logic error in trace_drop_common(), since we store only 64 drops, even if they are from same location. This fix is a one liner, but we probably need more work to avoid useless atomic dec/inc Now I can watch 1 Mpps drops through dropwatch... Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Neil Horman <nhorman@tuxdriver.com> Acked-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 4月, 2012 1 次提交
-
-
由 Eric W. Biederman 提交于
While reviewing the sysctl code in ax25 I spotted races in ax25_exit where it is possible to receive notifications and packets after already freeing up some of the data structures needed to process those notifications and updates. Call unregister_netdevice_notifier early so that the rest of the cleanup code does not need to deal with network devices. This takes advantage of my recent enhancement to unregister_netdevice_notifier to send unregister notifications of all network devices that are current registered. Move the unregistration for packet types, socket types and protocol types before we cleanup any of the ax25 data structures to remove the possibilities of other races. Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 4月, 2012 1 次提交
-
-
由 Eric Dumazet 提交于
Alexander Beregalov reported skb_over_panic errors and provided stack trace. I occurs commit a21d4572 (tcp: avoid order-1 allocations on wifi and tx path) added a regression, when a retransmit is done after a partial ACK. tcp_retransmit_skb() tries to aggregate several frames if the first one has enough available room to hold the following ones payload. This is controlled by /proc/sys/net/ipv4/tcp_retrans_collapse tunable (default : enabled) Problem is we must make sure _pskb_trim_head() doesnt fool skb_availroom() when pulling some bytes from skb (this pull is done when receiver ACK part of the frame). Reported-by: NAlexander Beregalov <a.beregalov@gmail.com> Cc: Marc MERLIN <marc@merlins.org> Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 4月, 2012 4 次提交
-
-
由 Julian Anastasov 提交于
ops_init should free the net_generic data on init failure and __register_pernet_operations should not call ops_free when NET_NS is not enabled. Signed-off-by: NJulian Anastasov <ja@ssi.bg> Reviewed-by: N"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
tcp_grow_window() has to grow rcv_ssthresh up to window_clamp, allowing sender to increase its window. tcp_grow_window() still assumes a tcp frame is under MSS, but its no longer true with LRO/GRO. This patch fixes one of the performance issue we noticed with GRO on. Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Acked-by: NNeal Cardwell <ncardwell@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Felix Fietkau 提交于
The broken check leads to rate control attempting to use HT40 while the driver is configured for HT20. This leads to interesting hardware issues. HT40 can only be used if the channel type is either HT40- or HT40+ and if the channel type of the cell matches the local type. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Cc: stable@vger.kernel.org Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
Cooked monitor rx was recently changed to use ieee80211_add_rx_radiotap_header instead of generating only limited radiotap information. ieee80211_add_rx_radiotap_header assumes that FCS info is still present if the hardware supports receiving it, however when cooked monitor rx packets are processed, FCS info has already been stripped. Fix this by adding an extra flag indicating FCS presence. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 17 4月, 2012 1 次提交
-
-
由 David Ward 提交于
A parameter set exists for WRED mode, called wred_set, to hold the same values for qavg and qidlestart across all VQs. The WRED mode values had been previously held in the VQ for the default DP. After these values were moved to wred_set, the VQ for the default DP was no longer created automatically (so that it could be omitted on purpose, to have packets in the default DP enqueued directly to the device without using RED). However, gred_dump() was overlooked during that change; in WRED mode it still reads qavg/qidlestart from the VQ for the default DP, which might not even exist. As a result, this command sequence will cause an oops: tc qdisc add dev $DEV handle $HANDLE parent $PARENT gred setup \ DPs 3 default 2 grio tc qdisc change dev $DEV handle $HANDLE gred DP 0 prio 8 $RED_OPTIONS tc qdisc change dev $DEV handle $HANDLE gred DP 1 prio 8 $RED_OPTIONS This fixes gred_dump() in WRED mode to use the values held in wred_set. Signed-off-by: NDavid Ward <david.ward@ll.mit.edu> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 4月, 2012 2 次提交
-
-
由 Lukasz Kucharczyk 提交于
Signed-off-by: NLukasz Kucharczyk <lukasz.kucharczyk@tieto.com> Cc: stable@vger.kernel.org Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Gao feng 提交于
If the ipv6 dst cache which copy from the dst generated by ICMPV6 RA packet. this dst cache will not check expire because it has no RTF_EXPIRES flag. So this dst cache will always be used until the dst gc run. Change the struct dst_entry,add a union contains new pointer from and expires. When rt6_info.rt6i_flags has no RTF_EXPIRES flag,the dst.expires has no use. we can use this field to point to where the dst cache copy from. The dst.from is only used in IPV6. rt6_check_expired check if rt6_info.dst.from is expired. ip6_rt_copy only set dst.from when the ort has flag RTF_ADDRCONF and RTF_DEFAULT.then hold the ort. ip6_dst_destroy release the ort. Add some functions to operate the RTF_EXPIRES flag and expires(from) together. and change the code to use these new adding functions. Changes from v5: modify ip6_route_add and ndisc_router_discovery to use new adding functions. Only set dst.from when the ort has flag RTF_ADDRCONF and RTF_DEFAULT.then hold the ort. Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 13 4月, 2012 6 次提交
-
-
由 Tomasz Gregorek 提交于
Added kfree_skb() calls in the chnk_net.c file on the error paths. Signed-off-by: NSjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 James Chapman 提交于
Applications using L2TP/IP sockets want to be able to bind() an L2TP/IP socket to set the local tunnel id while leaving the auto-assigned source address alone. So if no source address is supplied, don't overwrite the address already stored in the socket. Signed-off-by: NJames Chapman <jchapman@katalix.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 James Chapman 提交于
The l2tp_ip socket close handler does not update the module refcount correctly which prevents module unload after the first bind() call on an L2TPv3 IP encapulation socket. Signed-off-by: NJames Chapman <jchapman@katalix.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Julia Lawall 提交于
At the point of this error-handling code, alloc_skb has succeded, so free the resulting skb by jumping to the err label. Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric W. Biederman 提交于
Recently an oops was reported in phonet if there was a failure during network namespace creation. [ 163.733755] ------------[ cut here ]------------ [ 163.734501] kernel BUG at include/net/netns/generic.h:45! [ 163.734501] invalid opcode: 0000 [#1] PREEMPT SMP [ 163.734501] CPU 2 [ 163.734501] Pid: 19145, comm: trinity Tainted: G W 3.4.0-rc1-next-20120405-sasha-dirty #57 [ 163.734501] RIP: 0010:[<ffffffff824d6062>] [<ffffffff824d6062>] phonet_pernet+0x182/0x1a0 [ 163.734501] RSP: 0018:ffff8800674d5ca8 EFLAGS: 00010246 [ 163.734501] RAX: 000000003fffffff RBX: 0000000000000000 RCX: ffff8800678c88d8 [ 163.734501] RDX: 00000000003f4000 RSI: ffff8800678c8910 RDI: 0000000000000282 [ 163.734501] RBP: ffff8800674d5cc8 R08: 0000000000000000 R09: 0000000000000000 [ 163.734501] R10: 0000000000000000 R11: 0000000000000000 R12: ffff880068bec920 [ 163.734501] R13: ffffffff836b90c0 R14: 0000000000000000 R15: 0000000000000000 [ 163.734501] FS: 00007f055e8de700(0000) GS:ffff88007d000000(0000) knlGS:0000000000000000 [ 163.734501] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 163.734501] CR2: 00007f055e6bb518 CR3: 0000000070c16000 CR4: 00000000000406e0 [ 163.734501] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 163.734501] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 163.734501] Process trinity (pid: 19145, threadinfo ffff8800674d4000, task ffff8800678c8000) [ 163.734501] Stack: [ 163.734501] ffffffff824d5f00 ffffffff810e2ec1 ffff880067ae0000 00000000ffffffd4 [ 163.734501] ffff8800674d5cf8 ffffffff824d667a ffff880067ae0000 00000000ffffffd4 [ 163.734501] ffffffff836b90c0 0000000000000000 ffff8800674d5d18 ffffffff824d707d [ 163.734501] Call Trace: [ 163.734501] [<ffffffff824d5f00>] ? phonet_pernet+0x20/0x1a0 [ 163.734501] [<ffffffff810e2ec1>] ? get_parent_ip+0x11/0x50 [ 163.734501] [<ffffffff824d667a>] phonet_device_destroy+0x1a/0x100 [ 163.734501] [<ffffffff824d707d>] phonet_device_notify+0x3d/0x50 [ 163.734501] [<ffffffff810dd96e>] notifier_call_chain+0xee/0x130 [ 163.734501] [<ffffffff810dd9d1>] raw_notifier_call_chain+0x11/0x20 [ 163.734501] [<ffffffff821cce12>] call_netdevice_notifiers+0x52/0x60 [ 163.734501] [<ffffffff821cd235>] rollback_registered_many+0x185/0x270 [ 163.734501] [<ffffffff821cd334>] unregister_netdevice_many+0x14/0x60 [ 163.734501] [<ffffffff823123e3>] ipip_exit_net+0x1b3/0x1d0 [ 163.734501] [<ffffffff82312230>] ? ipip_rcv+0x420/0x420 [ 163.734501] [<ffffffff821c8515>] ops_exit_list+0x35/0x70 [ 163.734501] [<ffffffff821c911b>] setup_net+0xab/0xe0 [ 163.734501] [<ffffffff821c9416>] copy_net_ns+0x76/0x100 [ 163.734501] [<ffffffff810dc92b>] create_new_namespaces+0xfb/0x190 [ 163.734501] [<ffffffff810dca21>] unshare_nsproxy_namespaces+0x61/0x80 [ 163.734501] [<ffffffff810afd1f>] sys_unshare+0xff/0x290 [ 163.734501] [<ffffffff8187622e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 163.734501] [<ffffffff82665539>] system_call_fastpath+0x16/0x1b [ 163.734501] Code: e0 c3 fe 66 0f 1f 44 00 00 48 c7 c2 40 60 4d 82 be 01 00 00 00 48 c7 c7 80 d1 23 83 e8 48 2a c4 fe e8 73 06 c8 fe 48 85 db 75 0e <0f> 0b 0f 1f 40 00 eb fe 66 0f 1f 44 00 00 48 83 c4 10 48 89 d8 [ 163.734501] RIP [<ffffffff824d6062>] phonet_pernet+0x182/0x1a0 [ 163.734501] RSP <ffff8800674d5ca8> [ 163.861289] ---[ end trace fb5615826c548066 ]--- After investigation it turns out there were two issues. 1) Phonet was not implementing network devices but was using register_pernet_device instead of register_pernet_subsys. This was allowing there to be cases when phonenet was not initialized and the phonet net_generic was not set for a network namespace when network device events were being reported on the netdevice_notifier for a network namespace leading to the oops above. 2) phonet_exit_net was implementing a confusing and special case of handling all network devices from going away that it was hard to see was correct, and would only occur when the phonet module was removed. Now that unregister_netdevice_notifier has been modified to synthesize unregistration events for the network devices that are extant when called this confusing special case in phonet_exit_net is no longer needed. Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Acked-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric W. Biederman 提交于
We already synthesize events in register_netdevice_notifier and synthesizing events in unregister_netdevice_notifier allows to us remove the need for special case cleanup code. This change should be safe as it adds no new cases for existing callers of unregiser_netdevice_notifier to handle. Signed-off-by: NEric W. Biederman <ebiederm@xmission.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 4月, 2012 1 次提交
-
-
由 Samuel Ortiz 提交于
Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 4月, 2012 5 次提交
-
-
由 Eric Dumazet 提交于
Marc Merlin reported many order-1 allocations failures in TX path on its wireless setup, that dont make any sense with MTU=1500 network, and non SG capable hardware. After investigation, it turns out TCP uses sk_stream_alloc_skb() and used as a convention skb_tailroom(skb) to know how many bytes of data payload could be put in this skb (for non SG capable devices) Note : these skb used kmalloc-4096 (MTU=1500 + MAX_HEADER + sizeof(struct skb_shared_info) being above 2048) Later, mac80211 layer need to add some bytes at the tail of skb (IEEE80211_ENCRYPT_TAILROOM = 18 bytes) and since no more tailroom is available has to call pskb_expand_head() and request order-1 allocations. This patch changes sk_stream_alloc_skb() so that only sk->sk_prot->max_header bytes of headroom are reserved, and use a new skb field, avail_size to hold the data payload limit. This way, order-0 allocations done by TCP stack can leave more than 2 KB of tailroom and no more allocation is performed in mac80211 layer (or any layer needing some tailroom) avail_size is unioned with mark/dropcount, since mark will be set later in IP stack for output packets. Therefore, skb size is unchanged. Reported-by: NMarc MERLIN <marc@merlins.org> Tested-by: NMarc MERLIN <marc@merlins.org> Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Marc Merlin reported many order-1 allocations failures in TX path on its wireless setup, that dont make any sense with MTU=1500 network, and non SG capable hardware. Turns out part of the problem comes from pskb_expand_head() not using ksize() to get exact head size given by kmalloc(). Doing the same thing than __alloc_skb() allows more tailroom in skb and can prevent future reallocations. As a bonus, struct skb_shared_info becomes cache line aligned. Reported-by: NMarc MERLIN <marc@merlins.org> Tested-by: NMarc MERLIN <marc@merlins.org> Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Herbert Xu 提交于
As it stands the bridge IGMP snooping system will respond to group leave messages with queries for remaining membership. This is both unnecessary and undesirable. First of all any multicast routers present should be doing this rather than us. What's more the queries that we send may end up upsetting other multicast snooping swithces in the system that are buggy. In fact, we can simply remove the code that send these queries because the existing membership expiry mechanism doesn't rely on them anyway. So this patch simply removes all code associated with group queries in response to group leave messages. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neal Cardwell 提交于
Fix a code path in tcp_rcv_rtt_update() that was comparing scaled and unscaled RTT samples. The intent in the code was to only use the 'm' measurement if it was a new minimum. However, since 'm' had not yet been shifted left 3 bits but 'new_sample' had, this comparison would nearly always succeed, leading us to erroneously set our receive-side RTT estimate to the 'm' sample when that sample could be nearly 8x too high to use. The overall effect is to often cause the receive-side RTT estimate to be significantly too large (up to 40% too large for brief periods in my tests). Signed-off-by: NNeal Cardwell <ncardwell@google.com> Acked-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Commit c43b874d (tcp: properly initialize tcp memory limits) tried to fix a regression added in commits 4acb4190 & 3dc43e3e, but still get it wrong. Result is machines with low amount of memory have too small tcp_rmem[2] value and slow tcp receives : Per socket limit being 1/1024 of memory instead of 1/128 in old kernels, so rcv window is capped to small values. Fix this to match comment and previous behavior. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Glauber Costa <glommer@parallels.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 10 4月, 2012 6 次提交
-
-
由 Gao feng 提交于
in function nf_conntrack_init_net,when nf_conntrack_timeout_init falied, we should call nf_conntrack_ecache_fini to do rollback. but the current code calls nf_conntrack_timeout_fini. Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Jozsef Kadlecsik 提交于
It was reported that the Linux kernel sometimes logs: klogd: [2629147.402413] kernel BUG at net / netfilter / nf_conntrack_proto_tcp.c: 447! klogd: [1072212.887368] kernel BUG at net / netfilter / nf_conntrack_proto_tcp.c: 392 ipv4_get_l4proto() in nf_conntrack_l3proto_ipv4.c and tcp_error() in nf_conntrack_proto_tcp.c should catch malformed packets, so the errors at the indicated lines - TCP options parsing - should not happen. However, tcp_error() relies on the "dataoff" offset to the TCP header, calculated by ipv4_get_l4proto(). But ipv4_get_l4proto() does not check bogus ihl values in IPv4 packets, which then can slip through tcp_error() and get caught at the TCP options parsing routines. The patch fixes ipv4_get_l4proto() by invalidating packets with bogus ihl value. The patch closes netfilter bugzilla id 771. Signed-off-by: NJozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Jozsef Kadlecsik 提交于
IPv6 conntrack marked invalid packets as INVALID and let the user drop those by an explicit rule, while IPv4 conntrack dropped such packets itself. IPv4 conntrack is changed so that it marks INVALID packets and let the user to drop them. Signed-off-by: NJozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Julia Lawall 提交于
Free extra as done in the error-handling code just above. Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The nl80211 handling code should ensure as much as it can that the interface is in a valid state, it can certainly ensure the interface is running. Not doing so can cause calls through mac80211 into the driver that result in warnings and unspecified behaviour in the driver. Cc: stable@vger.kernel.org Reported-by: NBen Greear <greearb@candelatech.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The TU_TO_EXP_TIME() macro already includes the "jiffies +" piece of the calculation, so don't add jiffies again. Reported-by: NOliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Tested-by: NOliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 09 4月, 2012 2 次提交
-
-
由 Pablo Neira Ayuso 提交于
We may hit this in xt_LOG: net/built-in.o:xt_LOG.c:function dump_ipv6_packet: error: undefined reference to 'ip6t_ext_hdr' happens with these config options: CONFIG_NETFILTER_XT_TARGET_LOG=y CONFIG_IP6_NF_IPTABLES=m ip6t_ext_hdr is fairly small and it is called in the packet path. Make it static inline. Reported-by: NSimon Kirby <sim@netnation.com> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Changli Gao 提交于
For a picked up connection, the window win is scaled twice: one is by the initialization code, and the other is by the sender updating code. I use the temporary variable swin instead of modifying the variable win. Signed-off-by: NChangli Gao <xiaosuo@gmail.com> Acked-by: NJozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
- 06 4月, 2012 6 次提交
-
-
由 Eric Dumazet 提交于
As soon as an skb is queued into socket error queue, another thread can consume it, so we are not allowed to reference skb anymore, or risk use after free. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
As soon as an skb is queued into socket receive_queue, another thread can consume it, so we are not allowed to reference skb anymore, or risk use after free. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sasha Levin 提交于
A phonet packet is limited to USHRT_MAX bytes, this is never checked during tx which means that the user can specify any size he wishes, and the kernel will attempt to allocate that size. In the good case, it'll lead to the following warning, but it may also cause the kernel to kick in the OOM and kill a random task on the server. [ 8921.744094] WARNING: at mm/page_alloc.c:2255 __alloc_pages_slowpath+0x65/0x730() [ 8921.749770] Pid: 5081, comm: trinity Tainted: G W 3.4.0-rc1-next-20120402-sasha #46 [ 8921.756672] Call Trace: [ 8921.758185] [<ffffffff810b2ba7>] warn_slowpath_common+0x87/0xb0 [ 8921.762868] [<ffffffff810b2be5>] warn_slowpath_null+0x15/0x20 [ 8921.765399] [<ffffffff8117eae5>] __alloc_pages_slowpath+0x65/0x730 [ 8921.769226] [<ffffffff81179c8a>] ? zone_watermark_ok+0x1a/0x20 [ 8921.771686] [<ffffffff8117d045>] ? get_page_from_freelist+0x625/0x660 [ 8921.773919] [<ffffffff8117f3a8>] __alloc_pages_nodemask+0x1f8/0x240 [ 8921.776248] [<ffffffff811c03e0>] kmalloc_large_node+0x70/0xc0 [ 8921.778294] [<ffffffff811c4bd4>] __kmalloc_node_track_caller+0x34/0x1c0 [ 8921.780847] [<ffffffff821b0e3c>] ? sock_alloc_send_pskb+0xbc/0x260 [ 8921.783179] [<ffffffff821b3c65>] __alloc_skb+0x75/0x170 [ 8921.784971] [<ffffffff821b0e3c>] sock_alloc_send_pskb+0xbc/0x260 [ 8921.787111] [<ffffffff821b002e>] ? release_sock+0x7e/0x90 [ 8921.788973] [<ffffffff821b0ff0>] sock_alloc_send_skb+0x10/0x20 [ 8921.791052] [<ffffffff824cfc20>] pep_sendmsg+0x60/0x380 [ 8921.792931] [<ffffffff824cb4a6>] ? pn_socket_bind+0x156/0x180 [ 8921.794917] [<ffffffff824cb50f>] ? pn_socket_autobind+0x3f/0x90 [ 8921.797053] [<ffffffff824cb63f>] pn_socket_sendmsg+0x4f/0x70 [ 8921.798992] [<ffffffff821ab8e7>] sock_aio_write+0x187/0x1b0 [ 8921.801395] [<ffffffff810e325e>] ? sub_preempt_count+0xae/0xf0 [ 8921.803501] [<ffffffff8111842c>] ? __lock_acquire+0x42c/0x4b0 [ 8921.805505] [<ffffffff821ab760>] ? __sock_recv_ts_and_drops+0x140/0x140 [ 8921.807860] [<ffffffff811e07cc>] do_sync_readv_writev+0xbc/0x110 [ 8921.809986] [<ffffffff811958e7>] ? might_fault+0x97/0xa0 [ 8921.811998] [<ffffffff817bd99e>] ? security_file_permission+0x1e/0x90 [ 8921.814595] [<ffffffff811e17e2>] do_readv_writev+0xe2/0x1e0 [ 8921.816702] [<ffffffff810b8dac>] ? do_setitimer+0x1ac/0x200 [ 8921.818819] [<ffffffff810e2ec1>] ? get_parent_ip+0x11/0x50 [ 8921.820863] [<ffffffff810e325e>] ? sub_preempt_count+0xae/0xf0 [ 8921.823318] [<ffffffff811e1926>] vfs_writev+0x46/0x60 [ 8921.825219] [<ffffffff811e1a3f>] sys_writev+0x4f/0xb0 [ 8921.827127] [<ffffffff82658039>] system_call_fastpath+0x16/0x1b [ 8921.829384] ---[ end trace dffe390f30db9eb7 ]--- Signed-off-by: NSasha Levin <levinsasha928@gmail.com> Acked-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
commit 2f533844 (tcp: allow splice() to build full TSO packets) added a regression for splice() calls using SPLICE_F_MORE. We need to call tcp_flush() at the end of the last page processed in tcp_sendpages(), or else transmits can be deferred and future sends stall. Add a new internal flag, MSG_SENDPAGE_NOTLAST, acting like MSG_MORE, but with different semantic. For all sendpage() providers, its a transparent change. Only sock_sendpage() and tcp_sendpages() can differentiate the two different flags provided by pipe_to_sendpage() Reported-by: NTom Herbert <therbert@google.com> Cc: Nandita Dukkipati <nanditad@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: H.K. Jerry Chu <hkchu@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Mahesh Bandewar <maheshb@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: NEric Dumazet <eric.dumazet@gmail>com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dave Jiang 提交于
This is the fallout from adding memcpy alignment workaround for certain IOATDMA hardware. NetDMA will only use DMA engine that can handle byte align ops. Acked-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NDave Jiang <dave.jiang@intel.com> Signed-off-by: NDan Williams <dan.j.williams@intel.com>
-
由 Stephen Boyd 提交于
Many users of debugfs copy the implementation of default_open() when they want to support a custom read/write function op. This leads to a proliferation of the default_open() implementation across the entire tree. Now that the common implementation has been consolidated into libfs we can replace all the users of this function with simple_open(). This replacement was done with the following semantic patch: <smpl> @ open @ identifier open_f != simple_open; identifier i, f; @@ -int open_f(struct inode *i, struct file *f) -{ ( -if (i->i_private) -f->private_data = i->i_private; | -f->private_data = i->i_private; ) -return 0; -} @ has_open depends on open @ identifier fops; identifier open.open_f; @@ struct file_operations fops = { ... -.open = open_f, +.open = simple_open, ... }; </smpl> [akpm@linux-foundation.org: checkpatch fixes] Signed-off-by: NStephen Boyd <sboyd@codeaurora.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 05 4月, 2012 1 次提交
-
-
由 RongQing.Li 提交于
Convert array index from the loop bound to the loop index. And remove the void type conversion to ip6_mc_del1_src() return code, seem it is unnecessary, since ip6_mc_del1_src() does not use __must_check similar attribute, no compiler will report the warning when it is removed. v2: enrich the commit header Signed-off-by: NRongQing.Li <roy.qing.li@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-