When RSS is enabled, interrupt vector 0 does not receive any rx traffic.
The rx producer index fields for vector 0's status block should be
considered reserved in this case.  This patch changes the code to
respect these reserved fields, which avoids a kernel panic when these
fields take on non-zero values.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes this beauty into a statement that actually has an effect on amd64.
Tested-by: NPer Jessen <per@opensuse.org>
Signed-off-by: NBenjamin Poirier <bpoirier@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

ieee80211_mgd_teardown() is called on netdev removal, which
occurs after the vif was already removed from the low-level
driver, resulting in the following warning:

[ 4809.014734] ------------[ cut here ]------------
[ 4809.019861] WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211]()
[ 4809.030388] wlan0:  Failed check-sdata-in-driver check, flags: 0x4
[ 4809.036862] Modules linked in: wlcore_sdio(-) wl12xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[ 4809.046849] [<c001bd4c>] (unwind_backtrace+0x0/0x12c)
[ 4809.055937] [<c047cf1c>] (dump_stack+0x20/0x24)
[ 4809.065385] [<c003e334>] (warn_slowpath_common+0x5c/0x74)
[ 4809.075589] [<c003e408>] (warn_slowpath_fmt+0x40/0x48)
[ 4809.088291] [<bf033630>] (ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211])
[ 4809.102844] [<bf067f84>] (ieee80211_destroy_auth_data+0x80/0xa4 [mac80211])
[ 4809.116276] [<bf068004>] (ieee80211_mgd_teardown+0x5c/0x74 [mac80211])
[ 4809.129331] [<bf043f18>] (ieee80211_teardown_sdata+0xb0/0xd8 [mac80211])
[ 4809.141595] [<c03b5e58>] (rollback_registered_many+0x228/0x2f0)
[ 4809.153056] [<c03b5f48>] (unregister_netdevice_many+0x28/0x50)
[ 4809.165696] [<bf041ea8>] (ieee80211_remove_interfaces+0xb4/0xdc [mac80211])
[ 4809.179151] [<bf032174>] (ieee80211_unregister_hw+0x50/0xf0 [mac80211])
[ 4809.191043] [<bf0bebb4>] (wlcore_remove+0x5c/0x7c [wlcore])
[ 4809.201491] [<c02c6918>] (platform_drv_remove+0x24/0x28)
[ 4809.212029] [<c02c4d50>] (__device_release_driver+0x8c/0xcc)
[ 4809.222738] [<c02c4e84>] (device_release_driver+0x30/0x3c)
[ 4809.233099] [<c02c4258>] (bus_remove_device+0x10c/0x128)
[ 4809.242620] [<c02c26f8>] (device_del+0x11c/0x17c)
[ 4809.252150] [<c02c6de0>] (platform_device_del+0x28/0x68)
[ 4809.263051] [<bf0df49c>] (wl1271_remove+0x3c/0x50 [wlcore_sdio])
[ 4809.273590] [<c03806b0>] (sdio_bus_remove+0x48/0xf8)
[ 4809.283754] [<c02c4d50>] (__device_release_driver+0x8c/0xcc)
[ 4809.293729] [<c02c4e2c>] (driver_detach+0x9c/0xc4)
[ 4809.303163] [<c02c3d7c>] (bus_remove_driver+0xc4/0xf4)
[ 4809.312973] [<c02c5a98>] (driver_unregister+0x70/0x7c)
[ 4809.323220] [<c03809c4>] (sdio_unregister_driver+0x24/0x2c)
[ 4809.334213] [<bf0df458>] (wl1271_exit+0x14/0x1c [wlcore_sdio])
[ 4809.344930] [<c009b1a4>] (sys_delete_module+0x228/0x2a8)
[ 4809.354734] ---[ end trace 515290ccf5feb522 ]---

Rename ieee80211_mgd_teardown() to ieee80211_mgd_stop(),
and call it on ieee80211_do_stop().
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.

Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.

Note that we don't use queues 20 and higher today and
doing so needs more work than this.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.
Signed-off-by: NIngo van Lil <inguin@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY connect attempts fail if no PHY id is specified in the emac platform
data and another mdio bus has been registered before 'davinci_mdio' bus. In
this case when configuring the interface, there will be an attempt to
connect to already attached PHY on the previously registered mdio bus:

net eth1: PHY already attached
net eth1: could not connect to phy smsc911x-0:01
IP-Config: Failed to open eth1
IP-Config: Device `eth1' not found

Fix this by modifying match_first_device() to match first PHY device
on 'davinci_mdio' bus.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we receive an interrupt too early before we set up ports in the probe
function, there won't be any port ready to handle it.

Only registering the irq after the ports are setup fixes the problem,
and works fine without losing any interrupts.

This causes crashes in some situations:

[c000000f7ff7fd60] d000000008e223f0 .ehea_neq_tasklet+0x78/0x148 [ehea]
[c000000f7ff7fe00] c0000000000b6cac .tasklet_hi_action+0xdc/0x210
[c000000f7ff7fea0] c0000000000b7cc8 .__do_softirq+0x178/0x300
[c000000f7ff7ff90] c000000000022694 .call_do_softirq+0x14/0x24
[c000000f68ee7900] c000000000010e04 .do_softirq+0xec/0x110
[c000000f68ee79a0] c0000000000b789c .irq_exit+0xac/0xe0
[c000000f68ee7a20] c0000000000110bc .do_IRQ+0x114/0x2a8
[c000000f68ee7ae0] c00000000000553c hardware_interrupt_entry+0x18/0x1c
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The previous blkt defaults for OSA Express 4 cards produced inadequate
performance for streaming workloads. The present patch will apply a
set of more appropriate defaults.
Signed-off-by: NStefan Raspl <raspl@linux.vnet.ibm.com>
Reviewed-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There exist qeth sysfs blkt attributes to change the default blkt
values. But blkt changes are reset during online setting due to a 2nd
invocation of qeth_determine_capabilites(). This patch makes sure
blkt default values are configured during 1st run of
qeth_determine_capabilities() only. Thus blkt changes are kept
during online setting.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reported-by: NHorst Hartmann <horst.hartmann@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make smsc95xx recalculate the hard_mtu after adjusting the
hard_header_len.

Without this, usbnet adjusts the MTU down to 1488 bytes, and the host is
unable to receive standard 1500-byte frames from the device.

Inspired by same fix on cdc_eem 78fb72f7.

Tested on ARM/Beagle.
Signed-off-by: NStephane Fillod <fillods@users.sf.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bridge: set fake_rtable's dst to NULL to avoid kernel Oops

when bridge is deleted before tap/vif device's delete, kernel may
encounter an oops because of NULL reference to fake_rtable's dst.
Set fake_rtable's dst to NULL before sending packets out can solve
this problem.

v4 reformat, change br_drop_fake_rtable(skb) to {}

v3 enrich commit header

v2 introducing new flag DST_FAKE_RTABLE to dst_entry struct.

[ Use "do { } while (0)" for nop br_drop_fake_rtable()
  implementation -DaveM ]
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NPeter Huang <peter.huangpeng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull build system failure fix from Michal Marek:
 "This fixes build failure with newer gcc that adds some internal
  symbols that end in "__mod_*_device_table", but are not actually the
  tables themselves."

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  Fix modpost failures in fedora 17

Pull a few more md bug fixes from NeilBrown:
 "2 are tagged for -stable, one being for a fairly serious bug that can
  corrupt metadata and make it hard to recovery an array.  The other is
  for a more recent regression since 3.3"

* tag 'md-3.4-fixes' of git://neil.brown.name/md:
  md: fix possible corruption of array metadata on shutdown.
  md: don't call ->add_disk unless there is good reason.
  DM RAID: Use safe version of rdev_for_each

Pull dlm fixes from David Teigland:
 "This includes one short patch fixing the behavior of the QUECVT flag,
  which the gfs2 folks are waiting on."

* tag 'dlm-fixes-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
  dlm: fix QUECVT when convert queue is empty

Mel reports a BUG_ON(slot == NULL) in radix_tree_tag_set() on s390
3.0.13: called from __set_page_dirty_nobuffers() when page_remove_rmap()
tries to transfer dirty flag from s390 storage key to struct page and
radix_tree.

That would be because of reclaim's shrink_page_list() calling
add_to_swap() on this page at the same time: first PageSwapCache is set
(causing page_mapping(page) to appear as &swapper_space), then
page->private set, then tree_lock taken, then page inserted into
radix_tree - so there's an interval before taking the lock when the
radix_tree slot is empty.

We could fix this by moving __add_to_swap_cache()'s spin_lock_irq up
before the SetPageSwapCache.  But a better fix is simply to do what's
five years overdue: Ken Chen introduced __set_page_dirty_no_writeback()
(if !PageDirty TestSetPageDirty) for tmpfs to skip all the radix_tree
overhead, and swap is just the same - it ignores the radix_tree tag, and
does not participate in dirty page accounting, so should be using
__set_page_dirty_no_writeback() too.

s390 testing now confirms that this does indeed fix the problem.
Reported-by: NMel Gorman <mgorman@suse.de>
Signed-off-by: NHugh Dickins <hughd@google.com>
Acked-by: NMel Gorman <mgorman@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ken Chen <kenchen@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

commit c744a65c
  md: don't set md arrays to readonly on shutdown.

removed the possibility of a 'BUG' when data is written to an array
that has just been switched to read-only, but also introduced the
possibility that the array metadata could be corrupted.

If, when md_notify_reboot gets the mddev lock, the array is
in a state where it is assembled but hasn't been started (as can
happen if the personality module is not available, or in other unusual
situations), then incorrect metadata will be written out making it
impossible to re-assemble the array.

So only call __md_stop_writes() if the array has actually been
activated.

This patch is needed for any stable kernel which has had the above
commit applied.

Cc: stable@vger.kernel.org
Reported-by: NChristoph Nelles <evilazrael@evilazrael.de>
Signed-off-by: NNeilBrown <neilb@suse.de>

Commit 7bfec5f3

   md/raid5: If there is a spare and a want_replacement device, start replacement.

cause md_check_recovery to call ->add_disk much more often.
Instead of only when the array is degraded, it is now called whenever
md_check_recovery finds anything useful to do, which includes
updating the metadata for clean<->dirty transition.
This causes unnecessary work, and causes info messages from ->add_disk
to be reported much too often.

So refine md_check_recovery to only do any actual recovery checking
(including ->add_disk) if MD_RECOVERY_NEEDED is set.

This fix is suitable for 3.3.y:

Cc: stable@vger.kernel.org
Reported-by: NJan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: NNeilBrown <neilb@suse.de>

Fix segfault caused by using rdev_for_each instead of rdev_for_each_safe

Commit dafb20fa mistakenly replaced a safe
iterator with an unsafe one when making some macro changes.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

I keep getting the following messages on the log buffer:
[ 2167.097507] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.331305] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.332539] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.876605] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.877354] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2462.280756] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2615.651689] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU

From the code comment I understand that this something that can -
and does, quite frequently - happen.
Signed-off-by: NEldad Zack <eldad@fogrefinery.com>
Acked-by: Franky Lin<frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Under some circumstances, a PCI-based driver reports the following OOPs:

Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Oops: 0000 [#1] SMP
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Pid: 19627, comm: rmmod
Not tainted 3.2.9-2.fc16.x86_64 #1 LENOVO 05962RU/05962RU
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP:
0010:[<ffffffffa0418d39>]  [<ffffffffa0418d39>]
rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Process rmmod (pid:
19627, threadinfo ffff880050262000, task ffff8801156d5cc0)
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Stack:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000002
ffff8801176c2540 ffff880050263ca8 ffffffffa03348e7
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000282
0000000180150014 ffff880050263fd8 ffff8801176c2810
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  ffff880050263bc8
ffffffff810550e2 00000000000002c0 ffff8801176c0d40
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Call Trace:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  [<ffffffffa03348e7>]
_rtl_pci_rx_interrupt+0x187/0x650 [rtlwifi]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Code: ff 09 d0 89 07 48
83 c4 08 5b 5d c3 66 0f 1f 44 00 00 55 48 89 e5 53 48 83 ec 08 66 66
66 66 90 40 84 f6 89 d3 74 13 84 d2 75 57 <8b> 07 48 83 c4 08 5b 5d c1
e8 1f c3 0f 1f 00 84 d2 74 ed 80 fa
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP
[<ffffffffa0418d39>] rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  RSP <ffff880050263b58>
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] CR2: 00000000000006e0
Mar 19 08:14:35 kvothe kernel: [ 6584.646491] ---[ end trace
8636c766dcfbe0e6 ]---

This oops is due to interrupts not being disabled in this particular path.
Reported-by: NDave Airlie <airlied@gmail.com>
Tested-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution.  Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:

Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.

After that you need to reload the driver to get it working again.

This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097
https://bugzilla.redhat.com/show_bug.cgi?id=802106

This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.

Cc: stable@kernel.org
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ctx->vif is dereferenced in different part of iwlwifi code, so do not
nullify it.

This should address at least one of the possible reasons of WARNING at
iwlagn_mac_remove_interface, and perhaps some random crashes when
firmware reset is performed.

Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f8588
(ath9k_hw: Cleanup TX power calculation for AR9287).

Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.

Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.

Fix this by adding the missing call of the helper
function.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to unifying regulatory limit handling
commit ca2c68cc
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.

This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.

This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The QUECVT flag should not prevent conversions from
being granted immediately when the convert queue is
empty.
Signed-off-by: NDavid Teigland <teigland@redhat.com>

Pull ARM fixes from Russell King:
 "Here's my usual Sunday push, just for one revert which PeterZ hollered
  about after last weeks push.  Other than that, all seems strangely
  quiet as far as fixes go in non-platform ARM land at the moment."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  Revert "ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus"

Pull powerpc fixes from Benjamin Herrenschmidt:
 "Here are a few fixes for powerpc.  Note the addition to the generic
  irq.h.  This is part of a 3-patches regression fix for mpic due to
  changes in how IRQ_TYPE_NONE is being handled.  Thomas agreed to the
  addition of the new IRQ_TYPE_DEFAULT contant, however he hasn't
  replied with an Ack to the actual patch yet.  I don't to wait much
  longer with these patches tho."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/mpic: Properly set default triggers
  irq: Add IRQ_TYPE_DEFAULT for use by PIC drivers
  powerpc/mpic: Fix confusion between hw_irq and virq
  powerpc/pmac: Don't add_timer() twice
  powerpc/eeh: Fix crash caused by null eeh_dev
  powerpc/mpc85xx: add MPIC message dts node
  powerpc/mpic_msgr: fix offset error when setting mer register
  powerpc/mpic_msgr: add lock for MPIC message global variable
  powerpc/mpic_msgr: fix compile error when SMP disabled
  powerpc: fix build when CONFIG_BOOKE_WDT is enabled
  powerpc/85xx: don't call of_platform_bus_probe() twice

Pull networking fixes from David Miller:

 1) Fix namespace init and cleanup in phonet to fix some oopses, from
    Eric W. Biederman.

 2) Missing kfree_skb() in AF_KEY, from Julia Lawall.

 3) Refcount leak and source address handling fix in l2tp from James
    Chapman.

 4) Memory leak fix in CAIF from Tomasz Gregorek.

 5) When routes are cloned from ipv6 addrconf routes, we don't process
    expirations properly.  Fix from Gao Feng.

 6) Fix panic on DMA errors in atl1 driver, from Tony Zelenoff.

 7) Only enable interrupts in 8139cp driver after we've registered the
    IRQ handler.  From Jason Wang.

 8) Fix too many reads of KS_CIDER register in ks8851 during probe,
    fixing crashes on spurious interrupts.  From Matt Renzelmann.

 9) Missing include in ath5k driver and missing iounmap on probe
    failure, from Jonathan Bither.

10) Fix RX packet handling in smsc911x driver, from Will Deacon.

11) Fix ixgbe WoL on fiber by leaving the laser on during shutdown.

12) ks8851 needs MAX_RECV_FRAMES increased otherwise the internal MAC
    buffers are easily overflown.  Fix from Davide Cimingahi.

13) Fix memory leaks in peak_usb CAN driver, from Jesper Juhl.

14) gred packet scheduler can dump in WRED more when doing a netlink
    dump.  Fix from David Ward.

15) Fix MTU in USB smsc75xx driver, from Stephane Fillod.

16) Dummy device needs ->ndo_uninit handler to properly handle
    ->ndo_init failures.  From Hiroaki SHIMODA.

17) Fix TX fragmentation in ath9k driver, from Sujith Manoharan.

18) Missing RTNL lock in ixgbe PM resume, from Benjamin Poirier.

19) Missing iounmap in farsync WAN driver, from Julia Lawall.

20) With LRO/GRO, tcp_grow_window() is easily tricked into not growing
    the receive window properly, and this hurts performance.  Fix from
    Eric Dumazet.

21) Network namespace init failure can leak net_generic data, fix from
    Julian Anastasov.

22) Fix skb_over_panic due to mis-accounting in TCP for partially ACK'd
    SKBs.  From Eric Dumazet.

23) New IDs for qmi_wwan driver, from Bjørn Mork.

24) Fix races in ax25_exit(), from Eric W. Biederman.

25) IPV6 TCP doesn't handle TCP_MAXSEG socket option properly, copy over
    logic from the IPV4 side.  From Neal Cardwell.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
  tcp: fix TCP_MAXSEG for established IPv6 passive sockets
  drivers/net: Do not free an IRQ if its request failed
  drop_monitor: allow more events per second
  ks8851: Fix request_irq/free_irq mismatch
  net/hyperv: Adding cancellation to ensure rndis filter is closed
  ks8851: Fix mutex deadlock in ks8851_net_stop()
  net ax25: Reorder ax25_exit to remove races.
  icplus: fix interrupt for IC+ 101A/G and 1001LF
  net: qmi_wwan: support Sierra Wireless MC77xx devices in QMI mode
  bnx2x: off by one in bnx2x_ets_e3b0_sp_pri_to_cos_set()
  ksz884x: don't copy too much in netdev_set_mac_address()
  tcp: fix retransmit of partially acked frames
  netns: do not leak net_generic data on failed init
  net/sock.h: fix sk_peek_off kernel-doc warning
  tcp: fix tcp_grow_window() for large incoming frames
  drivers/net/wan/farsync.c: add missing iounmap
  davinci_mdio: Fix MDIO timeout check
  ipv6: clean up rt6_clean_expires
  ipv6: fix rt6_update_expires
  arcnet: rimi: Fix device name in debug output
  ...

This gets rid of the unused default senses array, and replaces the
incorrect use of IRQ_TYPE_NONE with the new IRQ_TYPE_DEFAULT for
the initial set_trigger() call when mapping an interrupt.

This in turn makes us read the HW state and update the irq desc
accordingly.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This is meant typically to allow a PIC driver's irq domain map() callback
to establish sane defaults for the interrupt (and make sure that the HW
and the irq_desc are in sync as far as the trigger is concerned).

The irq core may not call the set_trigger callback if it thinks the
trigger is already set to the right setting, so we need to ensure new
descriptors are properly synchronized with the hardware.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

mpic_is_ipi() takes a virq and immediately converts it to a hw_irq.

However, one of the two call sites calls it with a ... hw_irq. The
other call site also happens to have the hw_irq at hand, so let's
change it to just take that as an argument. Also change mpic_is_tm()
for consistency.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If the interrupt and the timeout happen roughly at the same
time, we can get into a situation where the timer function
is run while the interrupt has already been processed. In
this case, the timer function might end up doing an add_timer
on an already pending timer, causing a BUG_ON() to trigger.

Instead, just skip the whole timeout operation if we see that
the timer is pending. The spinlock ensures that the only way
that happens is if we already started a new operation and thus
the timeout can be ignored.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The problem was reported by Anton Blanchard. While EEH error
happened to the PCI device without the corresponding device
driver, kernel crash was seen. Eventually, I successfully
reproduced the problem on Firebird-L machine with utility
"errinjct". Initially, the device driver for Emulex ethernet
MAC has been disabled from .config and force data parity on
the Emulex ethernet MAC with help of "errinjct". Eventually,
I saw the kernel crash after issueing couple of "lspci -v"
command.

The root cause behind is that the PCI device, including the
reference to the corresponding eeh device, will be removed
from the system while EEH does recovery. Afterwards, the
PCI device will be probed again and added into the system
accordingly. So it's not safe to retrieve the eeh device from
the corresponding PCI device after the PCI device has been removed
and not added again.

The patch fixes the issue and retrieve the eeh device from OF node
instead of PCI device after the PCI device has been removed.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit f5fff5dc forgot to fix TCP_MAXSEG behavior IPv6 sockets, so IPv6
TCP server sockets that used TCP_MAXSEG would find that the advmss of
child sockets would be incorrect. This commit mirrors the advmss logic
from tcp_v4_syn_recv_sock in tcp_v6_syn_recv_sock. Eventually this
logic should probably be shared between IPv4 and IPv6, but this at
least fixes this issue.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refrain from attempting to free an interrupt line if the request
fails and hence, there is no IRQ to free.

CC: netdev@vger.kernel.org
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>