The iw_nes driver repeats the logic

	if (atomic_dec_and_test(&cqp_request->refcount)) {
		if (cqp_request->dynamic) {
			kfree(cqp_request);
		} else {
			spin_lock_irqsave(&nesdev->cqp.lock, flags);
			list_add_tail(&cqp_request->list, &nesdev->cqp_avail_reqs);
			spin_unlock_irqrestore(&nesdev->cqp.lock, flags);
		}
	}

over and over.  Wrap this up in functions nes_free_cqp_request() and
nes_put_cqp_request() to simplify such code.

In addition to making the source smaller and more readable, this shrinks
the compiled code quite a bit:

add/remove: 2/0 grow/shrink: 0/13 up/down: 164/-1692 (-1528)
function                                     old     new   delta
nes_free_cqp_request                           -     147    +147
nes_put_cqp_request                            -      17     +17
nes_modify_qp                               2316    2293     -23
nes_hw_modify_qp                             737     657     -80
nes_dereg_mr                                 945     860     -85
flush_wqes                                   501     416     -85
nes_manage_apbvt                             648     560     -88
nes_reg_mr                                  1117    1026     -91
nes_cqp_ce_handler                           927     769    -158
nes_alloc_mw                                1052     884    -168
nes_create_qp                               5314    5141    -173
nes_alloc_fmr                               2212    2035    -177
nes_destroy_cq                              1097     918    -179
nes_create_cq                               2787    2598    -189
nes_dealloc_mw                               762     566    -196
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NFaisal Latif <flatif@neteffect.com>

The patch tries to solve the problem of device going down and paths being
flushed on an SM change event. The method is to mark the paths as candidates for
refresh (by setting the new valid flag to 0), and wait for an ARP
probe a new path record query.

The solution requires a different and less intrusive handling of SM
change event. For that, the second argument of the flush function
changes its meaning from a boolean flag to a level.  In most cases, SM
failover doesn't cause LID change so traffic won't stop.  In the rare
cases of LID change, the remote host (the one that hadn't changed its
LID) will lose connectivity until paths are refreshed. This is no
worse than the current state.  In fact, preventing the device from
going down saves packets that otherwise would be lost.
Signed-off-by: NMoni Levy <monil@voltaire.com>
Signed-off-by: NMoni Shoua <monis@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This gives ehca an autogenerated modalias and therefore enables automatic loading.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add "ipoib_use_lro" module parameter to enable LRO and an
"ipoib_lro_max_aggr" module parameter to set the max number of packets
to be aggregated.  Make LRO controllable and LRO statistics accessible
through ethtool.
Signed-off-by: NVladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Set IB_QP_CREATE_BLOCK_MULTICAST_LOOPBACK for IPoIB's UD QPs if
supported by the underlying device.  This creates an improvement of up
to 39% in bandwidth when sending multicast packets with IPoIB, and an
improvment of 12% in cpu usage.
Signed-off-by: NRon Livne <ronli@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support for handling the IB_QP_CREATE_MULTICAST_BLOCK_LOOPBACK
flag by using the per-multicast group loopback blocking feature of
mlx4 hardware.
Signed-off-by: NRon Livne <ronli@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- Add a new rdma ctl command called RDMA_GET_MIB to the cxgb3 low
  level driver to obtain the protocol mib from the rnic hardware.

- Add new iw_cxgb3 provider method to get the MIB from the low level
  driver.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds a sysfs attribute group called "proto_stats" under
/sys/class/infiniband/$device/ and populates this group with protocol
statistics if they exist for a given device.  Currently, only iWARP
stats are defined, but the code is designed to allow InfiniBand
protocol stats if they become available.  These stats are per-device
and more importantly -not- per port.

Details:

- Add union rdma_protocol_stats in ib_verbs.h.  This union allows
  defining transport-specific stats.  Currently only iwarp stats are
  defined.

- Add struct iw_protocol_stats to define the current set of iwarp
  protocol stats.

- Add new ib_device method called get_proto_stats() to return protocol
  statistics.

- Add logic in core/sysfs.c to create iwarp protocol stats attributes
  if the device is an RNIC and has a get_proto_stats() method.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

For devices that don't support SRQs, ipoib_cm_post_receive_nonsrq() is
called from both ipoib_cm_handle_rx_wc() and ipoib_cm_nonsrq_init_rx(),
and these two callers are not synchronized against each other.
However, ipoib_cm_post_receive_nonsrq() always reuses the same receive
work request and scatter list structures, so multiple callers can end
up stepping on each other, which leads to posting garbled work
requests.

Fix this by having the caller pass in the ib_recv_wr and ib_sge
structures to use, and allocating new local structures in
ipoib_cm_nonsrq_init_rx().

Based on a patch by Pradeep Satyanarayana <pradeep@us.ibm.com> and
David Wilder <dwilder@us.ibm.com>, with debugging help from Hoang-Nam
Nguyen <hnguyen@de.ibm.com>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NSean Hefty <sean.hefty@intel.com>

The members struct iwch_rnic_attributes.vendor_id and .vendor_part_id
are write-only, so we might as well get rid of them.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NSteve Wise <swise@opengridcomputing.com>

- set fw_ver
- set hw_ver
- set max_qp_wr to something reasonable
- set max_cqe to something reasonable
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

During corner case testing, we noticed that some versions of ehca do
not properly transition to interrupt done in special load situations.
This can be resolved by periodically triggering EOI through H_EOI, if
EQEs are pending.
Signed-off-by: NStefan Roscher <stefan.roscher@de.ibm.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Commit 65adfa91 ("IB/mlx4: Fix RESET to RESET and RESET to ERROR
transitions") added some extra code to handle a QP state transition
from RESET to ERROR.  However, the latest 1.2.1 version of the IB spec
has clarified that this transition is actually not allowed, so we can
remove this extra code again.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Commit b18aad71 ("IB/mthca: Fix RESET to ERROR transition") added some
extra code to handle a QP state transition from RESET to ERROR.
However, the latest 1.2.1 version of the IB spec has clarified that
this transition is actually not allowed, so we can remove this extra
code again.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

I was reviewing the QP state transition diagram in the IB 1.2.1 spec
and the code for qp_state_table[], and noticed that the code allows a
QP to be modified from IB_QPS_RESET to IB_QPS_ERR whereas the notes
for figure 124 (pg 457) specifically says that this transition isn't
allowed.  This is a clarification from earlier versions of the IB
spec, which were ambiguous in this area and suggested that the RESET
to ERR transition was allowed.

Fix up the qp_state_table[] to make RESET->ERR not allowed.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ConnectX HCAs support the IB_MGMT_CLASS_CONG_MGMT management class, so
process MADs of this class through the MAD_IFC firmware command.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ConnectX returns the max message size it supports through the
QUERY_DEV_CAP firmware command.  When modifying a QP to RTR, the max
message size for the QP must be specified.  This value must not exceed
the value declared through QUERY_DEV_CAP.  The current code ignores
the max allowed size and unconditionally sets the value to 2^31.  This
patch sets all QPs to the max value allowed as returned from firmware.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- set IB_DEVICE_MEM_MGT_EXTENSIONS capability bit if fw supports it.
- set max_fast_reg_page_list_len device attribute.
- add iwch_alloc_fast_reg_mr function.
- add iwch_alloc_fastreg_pbl
- add iwch_free_fastreg_pbl
- adjust the WQ depth for kernel mode work queues to account for
  fastreg possibly taking 2 WR slots.
- add fastreg_mr work request support.
- add local_inv work request support.
- add send_with_inv and send_with_se_inv work request support.
- removed useless duplicate enums/defines for TPT/MW/MR stuff.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch adds support for the IB "base memory management extension"
(BMME) and the equivalent iWARP operations (which the iWARP verbs
mandates all devices must implement).  The new operations are:

 - Allocate an ib_mr for use in fast register work requests.

 - Allocate/free a physical buffer lists for use in fast register work
   requests.  This allows device drivers to allocate this memory as
   needed for use in posting send requests (eg via dma_alloc_coherent).

 - New send queue work requests:
   * send with remote invalidate
   * fast register memory region
   * local invalidate memory region
   * RDMA read with invalidate local memory region (iWARP only)

Consumer interface details:

 - A new device capability flag IB_DEVICE_MEM_MGT_EXTENSIONS is added
   to indicate device support for these features.

 - New send work request opcodes IB_WR_FAST_REG_MR, IB_WR_LOCAL_INV,
   IB_WR_RDMA_READ_WITH_INV are added.

 - A new consumer API function, ib_alloc_mr() is added to allocate
   fast register memory regions.

 - New consumer API functions, ib_alloc_fast_reg_page_list() and
   ib_free_fast_reg_page_list() are added to allocate and free
   device-specific memory for fast registration page lists.

 - A new consumer API function, ib_update_fast_reg_key(), is added to
   allow the key portion of the R_Key and L_Key of a fast registration
   MR to be updated.  Consumers call this if desired before posting
   a IB_WR_FAST_REG_MR work request.

Consumers can use this as follows:

 - MR is allocated with ib_alloc_mr().

 - Page list memory is allocated with ib_alloc_fast_reg_page_list().

 - MR R_Key/L_Key "key" field is updated with ib_update_fast_reg_key().

 - MR made VALID and bound to a specific page list via
   ib_post_send(IB_WR_FAST_REG_MR)

 - MR made INVALID via ib_post_send(IB_WR_LOCAL_INV),
   ib_post_send(IB_WR_RDMA_READ_WITH_INV) or an incoming send with
   invalidate operation.

 - MR is deallocated with ib_dereg_mr()

 - page lists dealloced via ib_free_fast_reg_page_list().

Applications can allocate a fast register MR once, and then can
repeatedly bind the MR to different physical block lists (PBLs) via
posting work requests to a send queue (SQ).  For each outstanding
MR-to-PBL binding in the SQ pipe, a fast_reg_page_list needs to be
allocated (the fast_reg_page_list is owned by the low-level driver
from the consumer posting a work request until the request completes).
Thus pipelining can be achieved while still allowing device-specific
page_list processing.

The 32-bit fast register memory key/STag is composed of a 24-bit index
and an 8-bit key.  The application can change the key each time it
fast registers thus allowing more control over the peer's use of the
key/STag (ie it can effectively be changed each time the rkey is
rebound to a page list).
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The connected mode implementation in the IPoIB driver has a large
overhead in the way SKBs are handled in the receive flow.  It usually
allocates an SKB with as big as was used in the currently received SKB
and moves unused fragments from the old SKB to the new one. This
involves a loop on all the remaining fragments and incurs overhead on
the CPU.  This patch, for small SKBs, allocates an SKB just large
enough to contain the received data and copies to it the data from the
received SKB.  The newly allocated SKB is passed to the stack and the
old SKB is reposted.

When running netperf, UDP small messages, without this pach I get:

    UDP UNIDIRECTIONAL SEND TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
    14.4.3.178 (14.4.3.178) port 0 AF_INET
    Socket  Message  Elapsed      Messages
    Size    Size     Time         Okay Errors   Throughput
    bytes   bytes    secs            #      #   10^6bits/sec

    114688     128   10.00     5142034      0     526.31
    114688           10.00     1130489            115.71

With this patch I get both send and receive at ~315 mbps.

The reason that send performance actually slows down is as follows:
When using this patch, the overhead of the CPU for handling RX packets
is dramatically reduced.  As a result, we do not experience RNR NAK
messages from the receiver which cause the connection to be closed and
reopened again; when the patch is not used, the receiver cannot handle
the packets fast enough so there is less time to post new buffers and
hence the mentioned RNR NACKs.  So what happens is that the
application *thinks* it posted a certain number of packets for
transmission but these packets are flushed and do not really get
transmitted.  Since the connection gets opened and closed many times,
each time netperf gets the CPU time that otherwise would have been
given to IPoIB to actually transmit the packets.  This can be verified
when looking at the port counters -- the output of ifconfig and the
oputput of netperf (this is for the case without the patch):

    tx packets
    ==========
    port counter:   1,543,996
    ifconfig:       1,581,426
    netperf:        5,142,034

    rx packets
    ==========
    netperf         1,1304,089
Signed-off-by: NEli Cohen <eli@mellanox.co.il>

They don't get updated by git and so they're worse than useless.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The idea is that for QPs with fixed size work requests (eg selective
signaling QPs), before stamping the WQE, we read the value of the DS
field, which gives the effective size of the descriptor as used in the
previous post.  Then we stamp only that area, since the rest of the
descriptor is already stamped.

When initializing the send queue buffer, make sure the DS field is
initialized to the max descriptor size so that the subsequent stamping
will be done on the entire descriptor area.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch solves a race that occurs after an event occurs that causes
the SA query module to flush its SM address handle (AH).  When SM AH
becomes invalid and needs an update it is handled by the global
workqueue.  On the other hand this event is also handled in the IPoIB
driver by queuing work in the ipoib_workqueue that does multicast
joins.  Although queuing is in the right order, it is done to 2
different workqueues and so there is no guarantee that the first to be
queued is the first to be executed.

This causes a problem because IPoIB may end up sending an request to
the old SM, which will take a long time to time out (since the old SM
is gone); this leads to a much longer than necessary interruption in
multicast traffer.

The patch sets the SA query module's SM AH to NULL when the event
occurs, and until update_sm_ah() is done, any request that needs sm_ah
fails with -EAGAIN return status.

For consumers, the patch doesn't make things worse.  Before the patch,
MADs are sent to the wrong SM so the request gets lost.  Consumers can
be improved if they examine the return code and respond to EAGAIN
properly but even without an improvement the situation is not getting
worse.
Signed-off-by: NMoni Levy <monil@voltaire.com>
Signed-off-by: NMoni Shoua <monis@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The license text for several files references a third software license
that was inadvertently copied in.  Update the license to what was
intended.  This update was based on a request from HP.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove an explicit memset(..., 0, ...) of a 'listener' structure
allocated with kzalloc().
Signed-off-by: NChristophe Jaillet <christophe.jaillet@wanadoo.fr>
Acked-by: NFaisal Latif <faisal@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The SRP initiator is currently using ib_find_cached_pkey() and
ib_get_cached_gid() in situations where the uncached ib_find_pkey()
and ib_query_gid() functions serve just as well: sleeping is allowed
and performance is not an issue.  Since we want to eliminate the
cached operations in the long term, convert SRP to use the uncached
variants.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove explicit lock_kernel() calls and document why the code is safe.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NJonathan Corbet <corbet@lwn.net>

The change to iwch_provider.c in commit f4e91eb4 ("IB: convert struct
class_device to struct device") undid the fix done in commit 7f049f2f
("RDMA/cxgb3: Hold rtnl_lock() around ethtool get_drvinfo call").  It
removed the calls to rtnl_lock() that serialized the iw_cxgb3 ethtool
ops calls into the cxgb3 driver.  This locking is needed to avoid
messing up the internal state of the cxgb3 driver.
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove explicit lock_kernel() calls and document why the code is safe.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NJonathan Corbet <corbet@lwn.net>

Current memfree FW has a bug which in some cases, assumes that ICM
pages passed to it are cleared.  This patch uses __GFP_ZERO to
allocate all ICM pages passed to the FW.  Once firmware with a fix is
released, we can make the workaround conditional on firmware version.

This fixes the bug reported by Arthur Kepner <akepner@sgi.com> here:
http://lists.openfabrics.org/pipermail/general/2008-May/050026.html

Cc: <stable@kernel.org>
Signed-off-by: NEli Cohen <eli@mellanox.co.il>

[ Rewritten to be a one-liner using __GFP_ZERO instead of vmap()ing
  ICM memory and memset()ing it to 0. - Roland ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NArnd Bergmann <arnd@arndb.de>

All of the open() functions which don't need the BKL on their face may
still depend on its acquisition to serialize opens against driver
initialization.  So make those functions acquire then release the BKL to be
on the safe side.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>

Be extra-cautious and protect the remaining open() functions.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>

This documents the fact that somebody looked at the relevant open()
functions and concluded that, due to their trivial nature, no locking was
needed.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>

Commit 1ae5c187 ("IB/uverbs: Don't store struct file * for event
files") changed the way that closed files are handled in the uverbs
code.  However, after the conversion, is_closed flag is checked
incorrectly in ib_uverbs_async_handler().  As a result, no async
events are ever passed to applications.

Found by: Ronni Zimmerman <ronniz@mellanox.co.il>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

nes_reg_user_mr() should fail if page_count becomes >= 1024 * 512
rather than just testing for strict >, because page_count is
essentially used as an index into an array with 1024 * 512 entries, so
allowing the loop to continue with page_count == 1024 * 512 means that
memory after the end of the array is corrupted.  This leads to a crash
triggerable by a userspace application that requests registration of a
too-big region.

Also get rid of the call to pci_free_consistent() here to avoid
corrupting state with a double free, since the same memory will be
freed in the code jumped to at reg_user_mr_err.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In 2.6.26, we added some support for send with invalidate work
requests, including a device capability flag to indicate whether a
device supports such requests.  However, the support was incomplete:
the completion structure was not extended with a field for the key
contained in incoming send with invalidate requests.

Full support for memory management extensions (send with invalidate,
local invalidate, fast register through a send queue, etc) is planned
for 2.6.27.  Since send with invalidate is not very useful by itself,
just remove the IB_DEVICE_SEND_W_INV bit before the 2.6.26 final
release; we will add an IB_DEVICE_MEM_MGT_EXTENSIONS bit in 2.6.27,
which makes things simpler for applications, since they will not have
quite as confusing an array of fine-grained bits to check.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>