The BPI-M2+ is an H3 development board. It is a smaller form factor than
the original BPI-M2, with the new H3 SoC.

It has 1GB DRAM, 8GB eMMC, a micro SD card slot, HDMI output, 2 USB
host connector and 1 USB OTG connector, an IR receiver, WiFi+BT based
on Ampak AP6212.

The board also has a 3 pin header for (debug) UART, a 40 pin GPIO header
based on the Raspberry Pi B+, but the peripheral signals are not the
same, and an FPC connector for connecting BPI's camera.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds a common device tree for all fifth generation Aspeed systems,
and a board specific device tree for the ast2500 evaluation board.
Signed-off-by: NJoel Stanley <joel@jms.id.au>

A common device tree for all forth gen/ast2400 systems and a board
specific dts for the Palmetto OpenPower developemnt machine which was
used for testing.
Signed-off-by: NJoel Stanley <joel@jms.id.au>

Add initial support for imx6ul pico hobbit board.

For information about this board, please visit:
http://www.wandboard.org/images/hobbit/hobbitboard-imx6ul-reva1.pdfSigned-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

To simplify matching of DTS files of all NXP LPC32xx powered boards by
a file name add 'lpc3250' prefix to PHYTEC PHYCORE-LPC3250 board dts
file.
Acked-by: NSylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>

To simplify matching of DTS files of all NXP LPC32xx powered boards by
a file name add 'lpc3250' prefix to Embedded Artists LPC3250 board dts
file.
Acked-by: NSylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>

Embest MarS Board [1] is a multi-core platform based on Freescale i.MX6
Cortex-A9 Dual Core, running up to 1GHz with 1 GB of RAM, 4GB of eMMC
and with a 4MB SPI flash.

[1] http://www.embest-tech.com/shop/star/marsboard.htmlSigned-off-by: NSergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Application Notes 399 and 400 shares the same memory map and
features. Both are shipped with Cortex-M7 and have the same  peripheral
as AN385/AN386, but with different location of PSRAM and Ethernet
controller.
Signed-off-by: NVladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>

Application Notes 385 and 386 shares the same memory map and features
except the CPU is used. AN385 is supplied with Cortex-M3 CPU and AN386
is supplied with Cortex-M4.
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>

Add Western Digital My Book World Edition device tree based on
Oxford Semiconductor OX810SE SoC.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

The MiQi is a rk3288-based devboard from Shenzen based mqmaker, with a
footprint the size of a credit card.

Main available outside connections are 4 usb ports, hdmi, gigabit
ethernet and two expansion headers.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Add support for board based on the popular Altera Cyclone V SoC.
This board has the following properties:
 - 1 GiB of DRAM
 - 1 Gigabit ethernet
 - 1 USB gadget port
 - 1 USB host port with an on-board hub
 - 2 QSPI NORs connected to the Cadence QSPI core
 - Multiple I2C EEPROMs and one I2C temperature sensor
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

This patch adds support to DB600c with basic serial ports.
DB600c is based on APQ8064.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

Initial board support dts files for DK01 board.
Signed-off-by: NSenthilkumar N L <snlakshm@codeaurora.org>
Signed-off-by: NVaradarajan Narayanan <varada@codeaurora.org>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

DRA72-EVM now has an upgrade to Rev C with SR2.0 silicon. As part of
this change, a few updates were factored in that were software
incompatible with previous board in few areas:
- We now use DP83867 ethernet phy instead of older DP838865 which fails
  in certain use cases.
- Two Ethernet ports now instead of the single one in rev B.
- polarities changed for certain pcf gpios
- Due to SoC phy current requirements, VDDA supplies are split between
 ldo3 and ldo2 (ldo2 was previously unused). NOTE: DSS (VDDA_VIDEO) is
 still supplied by ldo5, HDMI is now supplied by LDO2 instead of using
 LDO3.

NOTE: It does not make much sense to spin off a new board compatible
flag since there is no real benefit for the same.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This platform is based on a Marvell 88E6282 SoC and 88E6171 switch.

[gregory.clement@free-electrons.com: fix block comment style]
Signed-off-by: NBert Vermeulen <bert@biot.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NImre Kaloz <kaloz@openwrt.org>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add dts file to support Buffalo/Revogear Kurobox-Pro, which is marvell
orion5x based 3.5" HDD NAS.

It's a quite old product and already discontinued. So there's no
official website for it. But it was an early product which used marvell
orion5x 88F5182 chipset, it's popular in the community.
Some unofficial site:
  - http://buffalo.nas-central.org/wiki/Category:KuroboxPro
  - http://nice.kaze.com/KUROPRO_ProductSpecifications.pdf

This device tree is based on the board file:
  arch/arm/mach-orion5x/kurobox_pro-setup.c
However, the probing order of NAND and JEDEC-Flash are different from
the original board file, this results in incompatible minor number
for a few /dev/mtdX and /dev/mtdblockX devices.
So I still want to keep the board file for the time being.
Signed-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

As reported in [1], rename the k2* dts files to keystone-* files
this will force consistency throughout.

Script for the same (and hand modified for Makefile and MAINTAINERS
files):
for i in arch/arm/boot/dts/k2*
do
	b=`basename $i`;
	git mv $i arch/arm/boot/dts/keystone-$b;
	sed -i -e "s/$b/keystone-$b/g" arch/arm/boot/dts/*[si]
done

NOTE: bootloaders that depend on older dtb names will need to be
updated as well.

[1] http://marc.info/?l=linux-arm-kernel&m=145637407804754&w=2Reported-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NSantosh Shilimkar <ssantosh@kernel.org>

This commit adds support for Rev. B of a Zodiac Inflight Innovations
development board, mainly intended for DSA and ARINC 429 development
work.
Signed-off-by: NCory Tusar <cory.tusar@pid1solutions.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Introduce imx6sx-sdb-sai.dts so that it is possible to use the
SAI interface.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Based on i.MX6 SoloX with 1GB of RAM.

https://boundarydevices.com/product/nit6_solox-imx6/Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This baseboard can be used with all TX6 SoMs, but only a certain set
of combinations can be ordered by default. Add support for these
combinations in mainline, so that users can easily adopt their own
combination of SoM and baseboard themselves.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for the following i.MX6 based modules from Ka-Ro
electronics GmbH:
TX6S-8034:
Processor    Freescale i.MX 6 Solo, 800MHz
RAM          256MiB DDR3 SDRAM
ROM          128MiB NAND Flash
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6S-8035:
Processor    Freescale i.MX 6 Solo, 800MHz
RAM          512MiB DDR3 SDRAM
ROM          4GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6U-8033:
Processor    Freescale i.MX 6 Dual Lite, 800MHz
RAM          1GiB DDR3 SDRAM
ROM          4GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  industrial grade (-40°C/-25°C to 105°C Tj)

TX6Q-1036:
Processor    Freescale i.MX 6Quad, 1GHz
RAM          1GB DDR3 SDRAM 64-bit
ROM          8GiB eMMC
Power supply Single 3.1V to 5.5V
Size         31mm SO-DIMM
Temp. Range  Extended Consumer Grade (-20°C to 105°C Tj)
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Based on i.MX6 Quad Plus with 4GB of RAM.

https://boundarydevices.com/product/nitrogen6max/Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The TXUL-0010/-0011 modules are Computers On Module manufactured by
  Ka-Ro electronics GmbH with the following characteristics:
  Processor    Freescale i.MX 6UltraLite MCIMX6G2, 528 MHz
  RAM          256MB 16-bit DDR3 SDRAM
  ROM          128MB NAND Flash (TXUL-0010) / 4GB eMMC (TXUL-0011)
  Power supply Single 3.3 to 5V
  Size         26mm SO-DIMM
  Temp. Range  -40°C to 85°C
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Based on i.MX7 Dual with 1GB of RAM.

https://boundarydevices.com/product/nitrogen7/Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The Amazon Kindle Fire (first generation) codename kc1 is a tablet that was
released by Amazon back in 2011. It is using an OMAP4430 SoC GP version.

This adds devicetree support for the device, with only a few basic features
supported, such as debug uart, i2c and internal emmc.
Signed-off-by: NPaul Kocialkowski <contact@paulk.fr>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The AM572x-IDK board is a board based on TI's AM5728 SOC
which has a dual core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector

The link to the data sheet and TRM can be found here:

http://www.ti.com/product/AM5728

This patch creates a common dtsi file that will provide a common board
dtsi file to define the nodes that are common to AM57xx (including the
upcoming AM5718) IDK boards.

Initial support is only for basic peripherals
Signed-off-by: NSchuyler Patton <spatton@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

TI's Industrial Communication Engine EVM is a low cost hardware mainly
developed for industrial communication type applications using serial
or Ethernet based interfaces. This platform features TI's AM3359 with
800MHz single core Cortex-A8 processor, 256MB DDR3, 64MB SPI flash,
8MB NOR Flash, mmc, usb, can, dual Ethernet ports.

For more information, look at HW user guide[1], Data manual[2].

Just add basic support for the moment.

[1] http://processors.wiki.ti.com/index.php/AM335x_Industrial_Communication_Engine_EVM_Rev2_1_HW_User_Guide
[2] http://www.ti.com/lit/ds/symlink/am3359.pdfSigned-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds a devicetree for the ARM RealView PBA8 platform,
also known as HBI-0178, "RealView Platform Baseboard for
Cortex-A8" and PBX-A9 "RealView Platform Baseboard
Explore for Cortex-A9"

Tested in QEMU with -M realview-pb-a8, as well as with
-M realview-pbx-a9 -smp cpus=2

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: NRobin Murphy <robin.murphy@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ARM RealView Evaluation Baseboards are basically these:

- The original ARMv5 EB board with an ARM926EJ-S, ARM1136 or
  ARM1176 core tile here described in arm-realview-eb.dts
  no matter which of these core tiles is being used. This
  can be emulated by QEMU "realview-eb" machine, which by
  default will have the ARM926EJ-S core tile.

- The same board with one of three MPCore Core tiles:
  ARM11MPCore, not to be confused with the similar ARM
  PB11MPCore ARM11MPCore test system. This exist in
  two revisions:
  - Revision A modeled in arm-realview-eb-11mp.dts
  - Revision B modeled arm-realview-eb-11mp-revb.dts
    Revision B can be emulated by the QEMU
    "realview-eb-mpcore" machine, but to match the hardware
    also the argument -smp cpus=4 must be passed so that
    it has four CPU cores, like the hardware.

  There is also evidently from the code in the kernel a
  Cortex-A9 core tile for the EB, and this is modeled in
  arm-realview-eb-a9mp.dts based on the kernel boardfile.
  I have not found a user guide for this EB core tile on
  the ARM website and it seems uncommon. It is however
  included for completeness.

Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds the Device Tree source for Samsung ARTIK5 module[1]
based on Exynos3250 SoC. The ARTIK5 module includes the following
devices:
 - Application Processor (Samsung Exynos3250)
 - WiFi/BT Combo chip (Broadcom4354)
 - PMIC (Samsung S2MPS14)
 - eMMC (4GB)
 - DRAM LPDDR3 (512MB)
 - Connectors pin (60 Pins x 3 set)

Also, this patch adds the ARTIK5 evaluation board[2] dts file which includes
the ARTIK5 module[1] and have the devices such as sound codec, sd card port,
ethernet port, uart port and so on.

[1] https://www.artik.io/hardware/artik-5
[2] http://www.digikey.com/product-search/en?FV=ffecca14Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NAndi Shyti <andi.shyti@samsung.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>

Commit be3d7d02 ("ARM: kirkwood: Add DTS file for NSA320")
created the new file kirkwood-nsa320.dts but did not
add it to the Makefile.

Fixes: be3d7d02 ("ARM: kirkwood: Add DTS file for NSA320")
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Commit 2d0a7add ("ARM: Kirkwood: Add support for many Synology
NAS devices") created the new file kirkwood-ds112.dts but did not
add it to the Makefile.

Fixes: 2d0a7add ("ARM: Kirkwood: Add support for many Synology NAS devices")
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi PC is an SBC based on the Allwinner H3 SoC with a uSD slot,
3 USB ports directly from the SoC, a 10/100M ethernet port using the
SoC's integrated PHY, USB OTG, HDMI, a TRRS headphone jack for stereo out
and composite out, a microphone, an IR receiver, a CSI connector, 2 LEDs,
a 3 pin UART header, and a 40-pin GPIO header.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>