The BPI-M2+ is an H3 development board. It is a smaller form factor than
the original BPI-M2, with the new H3 SoC.

It has 1GB DRAM, 8GB eMMC, a micro SD card slot, HDMI output, 2 USB
host connector and 1 USB OTG connector, an IR receiver, WiFi+BT based
on Ampak AP6212.

The board also has a 3 pin header for (debug) UART, a 40 pin GPIO header
based on the Raspberry Pi B+, but the peripheral signals are not the
same, and an FPC connector for connecting BPI's camera.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add uart1 pins for 4 pin (RX/TX/RTS/CTS) mode.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move uart0 pins to sort the list of pin settings in alphabetical order.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is connected
to NMI pin of the SoC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is
connected to NMI pin of the SoC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The AXP809 PMIC is used with the Allwinner A80 SoC, along with
an AXP806 PMIC as a slave.

This patch adds a dtsi file for all the common bindings and default
values unrelated to board design. Currently this is just listing all
the regulator nodes. The regulators are initialized based on their
device node names.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

spi2 is available on the UEXT connector
Signed-off-by: NMichal Suchanek <hramrach@gmail.com>
[Maxime: Fixed the node order]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Used on A10s Olinuxino.
Signed-off-by: NMichal Suchanek <hramrach@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Q8 form factor A13 tablets have a 7" LCD panel. Unfortunately we
don't know the exact model of the panel. Just pick a panel with
display timings close to what we know.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Q8 tablets use the audio codec to provide audio output via a
headphone jack or a small mono speaker. A GPIO output is used to
control speaker amp.

The tablets may or may not have an internal microphone.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

On the A13 Q8 tablets, the PMIC's USB power supply (VBUS) is connected
to the external OTG port. This can be used to provide power and OTG VBUS
sensing.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The output pin of LDO is also a GPIO pin, and the on/off settings of the
regulator are actually pinmux settings.

Disable it by default so it doesn't conflict with GPIO usage.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Most of the display engine is shared between the R8 and the A13. Move the
common parts to the Á13 DTSI.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The RGB bus can be used in several configurations, one of which being the
RGB666.

Add a pinctrl group for that case.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the display and TCON clocks that are needed to drive the display
engine, tcon and TV encoders.
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the display and TCON clocks that are needed to drive the display
engine, tcon and TV encoders.
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Fix pll3x2 and pll7x2 not having a parent clock, specifically this
fixes the kernel turning of pll3 while simplefb is using it when
uboot has configured things to use pll3x2 as lcd ch clk parent.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we've a clock node describing pll3 we must add it to the
simplefb nodes clocks lists to avoid it getting turned off when
simplefb is used.

This fixes the screen going black when using simplefb.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The sun4i-timer driver registers its sched_clock only if the machine is
compatible with "allwinner,sun5i-a13", "allwinner,sun5i-a10s" or
"allwinner,sun4i-a10".
Add the missing "allwinner,sun5i-a13" string to the machine compatible.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 465a225f ("ARM: sun5i: Add C.H.I.P DTS")
Cc: <stable@vger.kernel.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The memory range assigned to the PMC (Power Management Controller) was
not including the PMC_PCR register which are used to control peripheral
clocks.

This was working fine thanks to the page granularity of ioremap(), but
started to fail when we switched to syscon/regmap, because regmap is
making sure that all accesses are falling into the reserved range.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: NRichard Genoud <richard.genoud@gmail.com>
Tested-by: NRichard Genoud <richard.genoud@gmail.com>
Fixes: 863a81c3 ("clk: at91: make use of syscon to share PMC registers in several drivers")
Cc: <stable@vger.kernel.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The device driver was added in v4.5 by commit dca536c4
("watchdog: add support for Sigma Designs SMP86xx/SMP87xx")
Signed-off-by: NMarc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This platform will use the new generic platdev driver.
Signed-off-by: NMarc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Commit fefe0535 ("clk: tango4: improve clkgen driver") added
support for USB and SDIO clocks.
Signed-off-by: NMarc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Define the CPU temperature sensor, and critical trip point.

Commit 799d71da471c ("add temperature sensor support for tango SoC")
added the device driver.
Acked-by: NEduardo Valentin <edubezval@gmail.com>
Signed-off-by: NMarc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

An error in documentation of the NAND Flash Controller (NFC) led to choose
another compatibility string for sama5d2 with an impact on the NAND flash
ready/busy information. It was producing the error message:

atmel_nand 80000000.nand: Time out to wait for interrupt: 0x08000000

and had an impact on performance.

So, switch back to the classical "atmel,sama5d3-nfc" compatibility string for
this SoC which gives the proper ready/busy bit information. The NAND flash
driver will be updated to remove the support for this different
implementation.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NRomain Izard <romain.izard.pro@gmail.com>
[nicolas.ferre@atmel.com: change commit message]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This adds a common device tree for all fifth generation Aspeed systems,
and a board specific device tree for the ast2500 evaluation board.
Signed-off-by: NJoel Stanley <joel@jms.id.au>

A common device tree for all forth gen/ast2400 systems and a board
specific dts for the Palmetto OpenPower developemnt machine which was
used for testing.
Signed-off-by: NJoel Stanley <joel@jms.id.au>

Enable pll3 and pll7 clocks that are needed by display clocks.
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

There are 3 kinds of OLinuXino Lime2 boards.
One without any on board storage, one with NAND storage and one with
eMMC storage. This patch adds the eMMC variant of boards.

eMMC storage is different from a regular SD card in that it is soldered
on the board and cannot be changed. Additionally, it shares pins with
the NAND module and with the second SPI port.
Signed-off-by: NOlliver Schinagl <oliver@schinagl.nl>
[Maxime: Removed the change log from the commit log]
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

MAX8997 PMIC requires interrupt and fails probing without it.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Fixes: d105f0b1 ("ARM: dts: Add basic dts file for Samsung Trats board")
Cc: <stable@vger.kernel.org>
[k.kozlowski: Write commit message, add CC-stable]
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>

The usage of slash character causes failure when creating regulator
debugfs entry.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
[k.kozlowski: Write commit message]
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>

The MFC nodes with the memory regions reserved for memory allocations
are missing in the Exynos5420 Peach Pit and Exynos5800 Peach Pi DTS.

This causes the s5p-mfc driver probe to fail with the following error:

[    4.140647] s5p_mfc_alloc_memdevs:1072: Failed to declare coherent memory for MFC device
[    4.216163] s5p-mfc: probe of 11000000.codec failed with error -12

Add the missing nodes so the driver probes and the {en,de}coder video
nodes are registered correctly:

[    4.096277] s5p-mfc 11000000.codec: decoder registered as /dev/video4
[    4.102282] s5p-mfc 11000000.codec: encoder registered as /dev/video5
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>

Add node to support SAMA5D4 hardware random number generator.
Signed-off-by: NMike Williams <mike@mikebwilliams.com>
[nicolas.ferre@atmel.com: reduce the register map size]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add node to support SAMA5D3 hardware random number generator.
Signed-off-by: NMike Williams <mike@mikebwilliams.com>
[nicolas.ferre@atmel.com: reduce the register map size]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add node to support SAMA5D2 hardware random number generator.
Signed-off-by: NMike Williams <mike@mikebwilliams.com>
[nicolas.ferre@atmel.com: reduce the register map size]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

No need to map 0x4000 bytes for the TRNG device: reduce it to 0x100.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable pll3 and pll7 clocks that are needed to drive display clocks.
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The CHIP has a composite output available muxed with the microphone in the
micro-jack plug.

Enable the composite output in its DTS.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The TCON, tv-encoder and display engine backends and frontends are combined
to create our display pipeline.

Add them to the R8 DTSI. It's supposed to be perfectly compatible with the
A10s and A13, but since we haven't tested it on them yet, it's safer to
just enable it on the R8. Eventually, it should be moved to sun5i.dtsi
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the display and TCON (channel 0 and channel 1) clocks that are going
to be needed to drive the display engine, tcon and TV encoders.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>