We have a few problems when returning to userspace. This is a
quick set of fixes for 3.3, I'll look into a more comprehensive
rework for 3.4. This fixes:

 - We kept interrupts soft-disabled when schedule'ing or calling
do_signal when returning to userspace as a result of a hardware
interrupt.

 - Rename do_signal to do_notify_resume like all other archs (and
do_signal_pending back to do_signal, which it was before Roland
changed it).

 - Add the missing call to key_replace_session_keyring() to
do_notify_resume().
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
---

In commit 54321242 ("Disable interrupts early in Program Check"), we
switched from enabling to disabling interrupts in program_check_common.

Whereas ENABLE_INTS leaves r3 untouched, if lockdep is enabled DISABLE_INTS
calls into lockdep code and will clobber r3. That means we pass a bogus
struct pt_regs* into program_check_exception() and all hell breaks loose.

So load our regs pointer into r3 after we call DISABLE_INTS.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

perf on POWER stopped working after commit e050e3f0 (perf: Fix
broken interrupt rate throttling). That patch exposed a bug in
the POWER perf_events code.

Since the PMCs count upwards and take an exception when the top bit
is set, we want to write 0x80000000 - left in power_pmu_start. We were
instead programming in left which effectively disables the counter
until we eventually hit 0x80000000. This could take seconds or longer.

With the patch applied I get the expected number of samples:

          SAMPLE events:       9948
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>

Program Check exceptions are the result of WARNs, BUGs, some
type of breakpoints, kprobe, and other illegal instructions.

We want interrupts (and thus preemption) to remain disabled
while doing the initial stage of testing the reason and
branching off to a debugger or kprobe, so we are still on
the original CPU which makes debugging easier in various cases.

This is how the code was intended, hence the local_irq_enable()
right in the middle of program_check_exception().

However, the assembly exception prologue for that exception was
incorrectly marked as enabling interrupts, which defeats that
(and records a redundant enable with lockdep).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

A kernel oops/panic prints an instruction dump showing several
instructions before and after the instruction which caused the
oops/panic.

The code intended that the faulting instruction be enclosed in angle
brackets, however a bug caused the faulting instruction to be
interpreted by printk() as the message log level.

To fix this, the KERN_CONT log level is added before the actual text of
the printed message.

=== Before the patch ===

[ 1081.587266] Instruction dump:
[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
[ 1081.602500]  4e800020 3803ffd0 2b800009

<4>[ 1081.587266] Instruction dump:
<4>[ 1081.590236] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[ 1081.598034] 3d20c03a 9009a114 7c0004ac 39200000
<98090000>[ 1081.602500]  4e800020 3803ffd0 2b800009

=== After the patch ===

[   51.385216] Instruction dump:
[   51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
[   51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009

<4>[   51.385216] Instruction dump:
<4>[   51.388186] 7c000110 7c0000f8 5400077c 552907f6 7d290378 992b0003 4e800020 38000001
<4>[   51.395986] 3d20c03a 9009a114 7c0004ac 39200000 <98090000> 4e800020 3803ffd0 2b800009
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This fixes a hang that was observed during live partition migration.
Since stop_topology_update must not be called from an interrupt
context, call it earlier in the migration process. The hang observed
can be seen below:

WARNING: at kernel/timer.c:1011
Modules linked in: ip6t_LOG xt_tcpudp xt_pkttype ipt_LOG xt_limit ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_raw xt_NOTRACK ipt_REJECT xt_state iptable_raw iptable_filter ip6table_mangle nf_conntrack_netbios_ns nf_conntrack_broadcast nf_conntrack_ipv4 nf_conntrack nf_defrag_ipv4 ip_tables ip6table_filter ip6_tables x_tables ipv6 fuse loop ibmveth sg ext3 jbd mbcache raid456 async_raid6_recov async_pq raid6_pq async_xor xor async_memcpy async_tx raid10 raid1 raid0 scsi_dh_alua scsi_dh_rdac scsi_dh_hp_sw scsi_dh_emc dm_round_robin dm_multipath scsi_dh sd_mod crc_t10dif ibmvfc scsi_transport_fc scsi_tgt scsi_mod dm_snapshot dm_mod
NIP: c0000000000c52d8 LR: c00000000004be28 CTR: 0000000000000000
REGS: c00000005ffd77d0 TRAP: 0700   Not tainted  (3.2.0-git-00001-g07d106d0)
MSR: 8000000000021032 <ME,CE,IR,DR>  CR: 48000084  XER: 00000001
CFAR: c00000000004be20
TASK = c00000005ec78860[0] 'swapper/3' THREAD: c00000005ec98000 CPU: 3
GPR00: 0000000000000001 c00000005ffd7a50 c000000000fbbc98 c000000000ec8340
GPR04: 00000000282a0020 0000000000000000 0000000000004000 0000000000000101
GPR08: 0000000000000012 c00000005ffd4000 0000000000000020 c000000000f3ba88
GPR12: 0000000000000000 c000000007f40900 0000000000000001 0000000000000004
GPR16: 0000000000000001 0000000000000000 0000000000000000 c000000001022310
GPR20: 0000000000000001 0000000000000000 0000000000200200 c000000001029e14
GPR24: 0000000000000000 0000000000000001 0000000000000040 c00000003f74bc80
GPR28: c00000003f74bc84 c000000000f38038 c000000000f16b58 c000000000ec8340
NIP [c0000000000c52d8] .del_timer_sync+0x28/0x60
LR [c00000000004be28] .stop_topology_update+0x20/0x38
Call Trace:
[c00000005ffd7a50] [c00000005ec78860] 0xc00000005ec78860 (unreliable)
[c00000005ffd7ad0] [c00000000004be28] .stop_topology_update+0x20/0x38
[c00000005ffd7b40] [c000000000028378] .__rtas_suspend_last_cpu+0x58/0x260
[c00000005ffd7bf0] [c0000000000fa230] .generic_smp_call_function_interrupt+0x160/0x358
[c00000005ffd7cf0] [c000000000036ec8] .smp_ipi_demux+0x88/0x100
[c00000005ffd7d80] [c00000000005c154] .icp_hv_ipi_action+0x5c/0x80
[c00000005ffd7e00] [c00000000012a088] .handle_irq_event_percpu+0x100/0x318
[c00000005ffd7f00] [c00000000012e774] .handle_percpu_irq+0x84/0xd0
[c00000005ffd7f90] [c000000000022ba8] .call_handle_irq+0x1c/0x2c
[c00000005ec9ba20] [c00000000001157c] .do_IRQ+0x22c/0x2a8
[c00000005ec9bae0] [c0000000000054bc] hardware_interrupt_entry+0x18/0x1c
Exception: 501 at .cpu_idle+0x194/0x2f8
    LR = .cpu_idle+0x194/0x2f8
[c00000005ec9bdd0] [c000000000017e58] .cpu_idle+0x188/0x2f8 (unreliable)
[c00000005ec9be90] [c00000000067ec18] .start_secondary+0x3e4/0x524
[c00000005ec9bf90] [c0000000000093e8] .start_secondary_prolog+0x10/0x14
Instruction dump:
ebe1fff8 4e800020 fbe1fff8 7c0802a6 f8010010 7c7f1b78 f821ff81 78290464
80090014 5400019e 7c0000d0 78000fe0 <0b000000> 4800000c 7c210b78 7c421378
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We use __get_cpu_var() which triggers a false positive warning
in smp_processor_id() thinking interrupts are enabled (at this
point, they are soft-enabled but hard-disabled).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 9deaa53a broke build
on platforms that use legacy_serial.c without also having
CONFIG_SERIAL_8250_FSL enabled due to an unconditional code
to a routine in that module.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

I could not find cpus_in_crash anywhere in the sourcetree, except for
arch/powerpc/kernel/crash.c. Moving the definition into the CONFIG_SMP
fixes it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Every arch calls:

if (unlikely(current->audit_context))
	audit_syscall_entry()

which requires knowledge about audit (the existance of audit_context) in
the arch code.  Just do it all in static inline in audit.h so that arch's
can remain blissfully ignorant.
Signed-off-by: NEric Paris <eparis@redhat.com>

The audit system previously expected arches calling to audit_syscall_exit to
supply as arguments if the syscall was a success and what the return code was.
Audit also provides a helper AUDITSC_RESULT which was supposed to simplify things
by converting from negative retcodes to an audit internal magic value stating
success or failure.  This helper was wrong and could indicate that a valid
pointer returned to userspace was a failed syscall.  The fix is to fix the
layering foolishness.  We now pass audit_syscall_exit a struct pt_reg and it
in turns calls back into arch code to collect the return value and to
determine if the syscall was a success or failure.  We also define a generic
is_syscall_success() macro which determines success/failure based on if the
value is < -MAX_ERRNO.  This works for arches like x86 which do not use a
separate mechanism to indicate syscall failure.

We make both the is_syscall_success() and regs_return_value() static inlines
instead of macros.  The reason is because the audit function must take a void*
for the regs.  (uml calls theirs struct uml_pt_regs instead of just struct
pt_regs so audit_syscall_exit can't take a struct pt_regs).  Since the audit
function takes a void* we need to use static inlines to cast it back to the
arch correct structure to dereference it.

The other major change is that on some arches, like ia64, MIPS and ppc, we
change regs_return_value() to give us the negative value on syscall failure.
THE only other user of this macro, kretprobe_example.c, won't notice and it
makes the value signed consistently for the audit functions across all archs.

In arch/sh/kernel/ptrace_64.c I see that we were using regs[9] in the old
audit code as the return value.  But the ptrace_64.h code defined the macro
regs_return_value() as regs[3].  I have no idea which one is correct, but this
patch now uses the regs_return_value() function, so it now uses regs[3].

For powerpc we previously used regs->result but now use the
regs_return_value() function which uses regs->gprs[3].  regs->gprs[3] is
always positive so the regs_return_value(), much like ia64 makes it negative
before calling the audit code when appropriate.
Signed-off-by: NEric Paris <eparis@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com> [for x86 portion]
Acked-by: Tony Luck <tony.luck@intel.com> [for ia64]
Acked-by: Richard Weinberger <richard@nod.at> [for uml]
Acked-by: David S. Miller <davem@davemloft.net> [for sparc]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [for mips]
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> [for ppc]

Use the more commonly used __noreturn instead of ATTRIB_NORETURN.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It's a very old and now unused prototype marking so just delete it.

Neaten panic pointer argument style to keep checkpatch quiet.
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Tracepoints should not be called inside an rcu_idle_enter/rcu_idle_exit
region. Since pSeries calls H_CEDE in the idle loop, we were violating
this rule.

commit a7b152d5 (powerpc: Tell RCU about idle after hcall tracing)
tried to work around it by delaying the rcu_idle_enter until after we
called the hcall tracepoint, but there are a number of issues with it.

The hcall tracepoint trampoline code is called conditionally when the
tracepoint is enabled. If the tracepoint is not enabled we never call
rcu_idle_enter. The idle_uses_rcu check was also done at compile time
which breaks multiplatform builds.

The simple fix is to avoid tracing H_CEDE and rely on other tracepoints
and the hypervisor dispatch trace log to work out if we called H_CEDE.

This fixes a hang during boot on pSeries.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Convert from pci_create_bus() to pci_create_root_bus().  This way the root
bus resources are correct immediately.  This patch doesn't fix a problem
because powerpc fixed the resources before scanning the bus, but it makes
powerpc more consistent with other architectures.

v2: fix build error with resource pointer passing

CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

No functional change.  This is so we can use pcibios_phb_map_io_space()
before we have a struct pci_bus.

v2: fix map io phb typo

CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch converts PowerPC's architecture-specific
'pcibios_set_master()' routine to a non-inlined function.  This will
allow follow on patches to create a generic 'pcibios_set_master()'
function using the '__weak' attribute which can be used by all
architectures as a default which, if necessary, can then be over-
ridden by architecture-specific code.

Converting 'pci_bios_set_master()' to a non-inlined function will
allow PowerPC's 'pcibios_set_master()' implementation to remain
architecture-specific after the generic version is introduced and
thus, not change current behavior.

No functional change.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMyron Stowe <myron.stowe@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

both proc_dir_entry ->mode and populating functions
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This moves the 'memory sysdev_class' over to a regular 'memory' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.

After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This moves the 'cpu sysdev_class' over to a regular 'cpu' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.

After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.

Userspace relies on events and generic sysfs subsystem infrastructure
from sysdev devices, which are made available with this conversion.

Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Len Brown <lenb@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since the PM core is now going to execute driver callbacks directly
if the corresponding subsystem callbacks are not present,
forward-only subsystem callbacks (i.e. such that only execute the
corresponding driver callbacks) are not necessary any more.  Thus
it is possible to remove generic_subsys_pm_ops, because the only
callback in there that is not forward-only, .runtime_idle, is not
really used by the only user of generic_subsys_pm_ops, which is
vio_bus_type.

However, the generic callback routines themselves cannot be removed
from generic_ops.c, because they are used individually by a number
of subsystems.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

The following patch adds relocatable kernel support - based on processing
of dynamic relocations - for PPC44x kernel.

We find the runtime address of _stext and relocate ourselves based
on the following calculation.

	virtual_base = ALIGN(KERNELBASE,256M) +
			MODULO(_stext.run,256M)

relocate() is called with the Effective Virtual Base Address (as
shown below)

            | Phys. Addr| Virt. Addr |
Page (256M) |------------------------|
Boundary    |           |            |
            |           |            |
            |           |            |
Kernel Load |___________|_ __ _ _ _ _|<- Effective
Addr(_stext)|           |      ^     |Virt. Base Addr
            |           |      |     |
            |           |      |     |
            |           |reloc_offset|
            |           |      |     |
            |           |      |     |
            |           |______v_____|<-(KERNELBASE)%256M
            |           |            |
            |           |            |
            |           |            |
Page(256M)  |-----------|------------|
Boundary    |           |            |

The virt_phys_offset is updated accordingly, i.e,

	virt_phys_offset = effective. kernel virt base - kernstart_addr

I have tested the patches on 440x platforms only. However this should
work fine for PPC_47x also, as we only depend on the runtime address
and the current TLB XLAT entry for the startup code, which is available
in r25. I don't have access to a 47x board yet. So, it would be great if
somebody could test this on 47x.
Signed-off-by: NSuzuki K. Poulose <suzuki@in.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

The following patch implements the dynamic relocation processing for
PPC32 kernel. relocate() accepts the target virtual address and relocates
 the kernel image to the same.

Currently the following relocation types are handled :

	R_PPC_RELATIVE
	R_PPC_ADDR16_LO
	R_PPC_ADDR16_HI
	R_PPC_ADDR16_HA

The last 3 relocations in the above list depends on value of Symbol indexed
whose index is encoded in the Relocation entry. Hence we need the Symbol
Table for processing such relocations.

Note: The GNU ld for ppc32 produces buggy relocations for relocation types
that depend on symbols. The value of the symbols with STB_LOCAL scope
should be assumed to be zero. - Alan Modra
Signed-off-by: NSuzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: NJosh Poimboeuf <jpoimboe@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Modra <amodra@au1.ibm.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

DYNAMIC_MEMSTART(old RELOCATABLE) was restricted only to PPC_47x variants
of 44x. This patch enables DYNAMIC_MEMSTART for 440x based chipsets.
Signed-off-by: NSuzuki K. Poulose <suzuki@in.ibm.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

The current implementation of CONFIG_RELOCATABLE in BookE is based
on mapping the page aligned kernel load address to KERNELBASE. This
approach however is not enough for platforms, where the TLB page size
is large (e.g, 256M on 44x). So we are renaming the RELOCATABLE used
currently in BookE to DYNAMIC_MEMSTART to reflect the actual method.

The CONFIG_RELOCATABLE for PPC32(BookE) based on processing of the
dynamic relocations will be introduced in the later in the patch series.

This change would allow the use of the old method of RELOCATABLE for
platforms which can afford to enforce the page alignment (platforms with
smaller TLB size).

Changes since v3:

* Introduced a new config, NONSTATIC_KERNEL, to denote a kernel which is
  either a RELOCATABLE or DYNAMIC_MEMSTART(Suggested by: Josh Boyer)
Suggested-by: NScott Wood <scottwood@freescale.com>
Tested-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NSuzuki K. Poulose <suzuki@in.ibm.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

We have an array of 16 entries and a loop of 32 iterations... oops.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

As the kernels and initrd's get bigger boot-loaders and possibly
kexec-tools will need to place the initrd outside the RMO.  When this
happens we end up with no lowmem and the boot doesn't get very far.

Only use initrd_end as the limit for alloc_bottom if it's inside the
RMO.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit d57af9b2 (taskstats: use real microsecond granularity for CPU times)
renamed msecs_to_cputime to usecs_to_cputime, but failed to update all
numbers on the way.  This causes nonsensical cpu idle/iowait values to be
displayed in /proc/stat (the only user of usecs_to_cputime so far).

This also renames __cputime_msec_factor to __cputime_usec_factor, adapting
its value and using it directly in cputime_to_usecs instead of doing two
multiplications.
Signed-off-by: NAndreas Schwab <schwab@linux-m68k.org>
Acked-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.

Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

The PowerPC pSeries platform (CONFIG_PPC_PSERIES=y) enables
hypervisor-call tracing for CONFIG_TRACEPOINTS=y kernels.  One of the
hypervisor calls that is traced is the H_CEDE call in the idle loop
that tells the hypervisor that this OS instance no longer needs the
current CPU.  However, tracing uses RCU, so this combination of kernel
configuration variables needs to avoid telling RCU about the current CPU's
idleness until after the H_CEDE-entry tracing completes on the one hand,
and must tell RCU that the the current CPU is no longer idle before the
H_CEDE-exit tracing starts.

In all other cases, it suffices to inform RCU of CPU idleness upon
idle-loop entry and exit.

This commit makes the required adjustments.
Signed-off-by: NPaul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>

It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.

To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().

If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().

Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:

- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>

The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:

- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.

There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.

Split this function into:

- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.

- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).

To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().

This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>

Sending a break on the SOC UARTs found in some MPC83xx/85xx/86xx
chips seems to cause a short lived IRQ storm (/proc/interrupts
typically shows somewhere between 300 and 1500 events).  Unfortunately
this renders SysRQ over the serial console completely inoperable.

The suggested workaround in the errata is to read the Rx register,
wait one character period, and then read the Rx register again.
We achieve this by tracking the old LSR value, and on the subsequent
interrupt event after a break, we don't read LSR, instead we just
read the RBR again and return immediately.

The "fsl,ns16550" is used in the compatible field of the serial
device to mark UARTs known to have this issue.

Thanks to Scott Wood for providing the errata data which led to
a much cleaner fix.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Based on original work by David 'Shaggy' Kleikamp.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NJosh Boyer <jwboyer@gmail.com>

The only function of memblock_analyze() is now allowing resize of
memblock region arrays.  Rename it to memblock_allow_resize() and
update its users.

* The following users remain the same other than renaming.

  arm/mm/init.c::arm_memblock_init()
  microblaze/kernel/prom.c::early_init_devtree()
  powerpc/kernel/prom.c::early_init_devtree()
  openrisc/kernel/prom.c::early_init_devtree()
  sh/mm/init.c::paging_init()
  sparc/mm/init_64.c::paging_init()
  unicore32/mm/init.c::uc32_memblock_init()

* In the following users, analyze was used to update total size which
  is no longer necessary.

  powerpc/kernel/machine_kexec.c::reserve_crashkernel()
  powerpc/kernel/prom.c::early_init_devtree()
  powerpc/mm/init_32.c::MMU_init()
  powerpc/mm/tlb_nohash.c::__early_init_mmu()  
  powerpc/platforms/ps3/mm.c::ps3_mm_add_memory()
  powerpc/platforms/embedded6xx/wii.c::wii_memory_fixups()
  sh/kernel/machine_kexec.c::reserve_crashkernel()

* x86/kernel/e820.c::memblock_x86_fill() was directly setting
  memblock_can_resize before populating memblock and calling analyze
  afterwards.  Call memblock_allow_resize() before start populating.

memblock_can_resize is now static inside memblock.c.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>

* early_init_devtree(): Total memory size is aligned to PAGE_SIZE;
  however, alignment isn't enforced if memory_limit is explicitly
  specified.  Simplify the logic and always apply PAGE_SIZE alignment.

* MMU_init(): memblock regions is truncated by directly modifying
  memblock.memory.cnt.  This is incomplete (reserved array is not
  truncated) and unnecessarily low level hindering further memblock
  improvments.  Use memblock_enforce_memory_limit() instead.

* wii_memory_fixups(): Unnecessarily low level direct manipulation of
  memblock regions.  The same result can be achieved using properly
  abstracted operations.  Reimplement using memblock API.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>

memblock_init() initializes arrays for regions and memblock itself;
however, all these can be done with struct initializers and
memblock_init() can be removed.  This patch kills memblock_init() and
initializes memblock with struct initializer.

The only difference is that the first dummy entries don't have .nid
set to MAX_NUMNODES initially.  This doesn't cause any behavior
difference.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>

This fixes a problem where a CPU thread coming out of nap mode can
think it has valid values in the nonvolatile GPRs (r14 - r31) as saved
away in power7_idle, but in fact the values have been trashed because
the thread was used for KVM in the mean time.  The result is that the
thread crashes because code that called power7_idle (e.g.,
pnv_smp_cpu_kill_self()) goes to use values in registers that have
been trashed.

The bit field in SRR1 that tells whether state was lost only reflects
the most recent nap, which may not have been the nap instruction in
power7_idle.  So we need an extra PACA field to indicate that state
has been lost even if SRR1 indicates that the most recent nap didn't
lose state.  We clear this field when saving the state in power7_idle,
we set it to a non-zero value when we use the thread for KVM, and we
test it in power7_wakeup_noloss.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

At present, on the powernv platform, if you off-line a CPU that was
online, and then try to on-line it again, the kernel generates a
warning message "OPAL Error -1 starting CPU n".  Furthermore, if the
CPU is a secondary thread that was used by KVM while it was off-line,
the CPU fails to come online.

The first problem is fixed by only calling OPAL to start the CPU the
first time it is on-lined, as indicated by the cpu_start field of its
PACA being zero.  The second problem is fixed by restoring the
cpu_start field to 1 instead of 0 when using the CPU within KVM.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>