This includes adding pernet_operations, empty init and exit
hooks and a bit of changes in sysctl_ipv4_init just not to
have this part in next patches.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Optimize call routing between NATed endpoints: when an external
registrar sends a media description that contains an existing RTP
expectation from a different SNATed connection, the gatekeeper
is trying to route the call directly between the two endpoints.

We assume both endpoints can reach each other directly and
"un-NAT" the addresses, which makes the media stream go between
the two endpoints directly.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for multiple media channels and use it to create
expectations for video streams when present.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SDP connection addresses may be contained in the payload multiple
times (in the session description and/or once per media description),
currently only the session description is properly updated. Split up
SDP mangling so the function setting up expectations only updates the
media port, update connection addresses from media descriptions while
parsing them and at the end update the session description when the
final addresses are known.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create expectations for the RTCP connections in addition to RTP connections.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Media streams can come from anywhere, add a module parameter which
controls whether wildcard expectations or expectations between the
two signalling endpoints are created.

Since the same media description sent on multiple connections may
results in multiple identical expections when using a wildcard source,
we need to check whether a similar expectation already exists for a
different connection before attempting to register it.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create expectations for incoming signalling connections when seeing
a REGISTER request. This is needed when the registrar uses a
different source port number for signalling messages and for receiving
incoming calls from other endpoints than the registrar.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SIP message may contain multiple Contact: addresses referring to
the NATed endpoint, translate all of them.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update maddr=, received= and rport= Via-header parameters refering to
the signalling connection.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce URI and header parameter parsing helpers. These are needed
by the conntrack helper to parse expiration values in Contact: header
parameters and by the NAT helper to properly update the Via-header
rport=, received= and maddr= parameters.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flush the RTP expectations we've created when a call is hung up or
terminated otherwise.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both may contains SDP offers/answers.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Perform NAT last after parsing the packet. This makes no difference
currently, but is needed when dealing with registrations to make
sure we seen the unNATed addresses.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for per-method request/response handlers and perform SDP
parsing for INVITE/UPDATE requests and for all informational and
successful responses.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the URI parsing helper to get the numerical addresses and get rid of the
text based header translation.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a helper function to parse a SIP-URI in a header value, optionally
iterating through all headers of this kind.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce new function for SIP header parsing that properly deals with
continuation lines and whitespace in headers and use it.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The request URI is not a header and needs to be treated differently than
real SIP headers. Add a seperate function for parsing it and get rid of
the POS_REQ_URI/POS_REG_REQ_URI definitions.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SDP and SIP headers are quite different, SIP can have continuation lines,
leading and trailing whitespace after the colon and is mostly case-insensitive
while SDP headers always begin on a new line and are followed by an equal
sign and the value, without any whitespace.

Introduce new SDP header parsing function and convert all users that used
the SIP header parsing function. This will allow to properly deal with the
special SIP cases in the SIP header parsing function later.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace sizeof/memcmp by strlen/strcmp. Use case-insensitive comparison
for SIP methods and the SIP/2.0 string, as specified in RFC 3261.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The conntrack reference and ctinfo can be derived from the packet.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After mangling the packet, the pointer to the data and the length of the data
portion may change and need to be adjusted.

Use double data pointers and a pointer to the length everywhere and add a
helper function to the NAT helper for performing the adjustments.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"limit" marks the first character outside the bounds.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to set up the destination NAT mapping before the source NAT
mapping, so the NAT core gets to see the final tuple and can decide
whether the source port needs to be remapped.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce expectation classes and policies. An expectation class
is used to distinguish different types of expectations by the
same helper (for example audio/video/t.120). The expectation
policy is used to hold the maximum number of expectations and
the initial timeout for each class.

The individual classes are isolated from each other, which means
that for example an audio expectation will only evict other audio
expectations.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is useful for the SIP helper and signalling expectations.
We don't want to create a full-blown expectation with a wildcard
as source based on a single UDP packet, but need to know the
final port anyways. With inactive expectations we can register
the expectation and reserve the tuple, but wait for confirmation
from the registrar before activating it.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With nf_conntrack DUMP_TUPLE got renamed to NF_CT_DUMP_TUPLE, fix
CLUSTERIP to use the proper macro name.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Default WMM params have to be set according to beacon/probe response
information prior to authentication (or IBSS start/join); beacon queue
is configured only in IBSS. This does not affect the use of 'real' WMM
params as reported by AP.
Signed-off-by: NVladimir Koutny <vlado@ksp.sk>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Postpone calling ieee80211_hw_config if hardware scanning is active.
This is similar to solution for software scanning where channel setting
is delayed until scan complete.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds a clean tear down for all block ack sessions if interface
goes down or if a deauthentication is done.
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch also fixes the Rx timer's comments
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a wrong debug print when receiving delba
Signed-off-by: NRon Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When you have an AP on channel 13, it will currently often enough
be listed in scan results even when the regulatory domain restricts
to channels 1-11. This is due to channel overlap. To avoid getting
very strange failures, don't show such APs in the scan results. The
failure mode will now go from "I can see the AP but not associate"
to "I can't see the AP although I know it's there" which is easier
to debug.

This problem was first really noticed by Jes Sorensen.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the new ieee80211_get_channel() function instead of open-coding it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add ieee80211_get_channel() which gets you a channel struct for a
specific wiphy if that channel is present in that wiphy.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch makes mac80211 able to send a phase1 key for TKIP
decryption.
This is needed for drivers that don't do the rekeying by themselves
(i.e. iwlwifi). Upon IV16 wrap around, the packet is decrypted in SW,
if decryption is ok, mac80211 calls to update_tkip_key  with a new
phase 1 RX key.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>