This includes adding pernet_operations, empty init and exit
hooks and a bit of changes in sysctl_ipv4_init just not to
have this part in next patches.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent commits from YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
have been introduced a several compilation warnings
'assignment discards qualifiers from pointer target type'
due to extra const modifier in the inline call parameters of
{dev|sock|twsk}_net_set.

Drop it.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit commit c346dca1
([NET] NETNS: Omit net_device->nd_net without CONFIG_NET_NS)
breaks compilation with CONFIG_NET_NS set.

Fix the typo.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Fix Rx/Tx HW interrupt coalescing counter reset logic. Disabling
is required before resetting the counter.

- Update the Default both Rx and Tx coalescing timer
threshold. Formerly 4 is set which is equal to 1.5 frame at the line
rate of 1GbE interface, and it doesn't match to the coalescing frame
count which is set to 16. Threashold 21 is matched to frame count 16.
Signed-off-by: NDai Haruki <dai.haruki@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

If the LAST bit is not set in the RxBD, it's possible we're processing
an incomplete frame, which is bad.  While we're at it, add a constant
for the error bitmask, so the whole if-clause fits on one line,
and is more legible.
Signed-off-by: NDai Haruki <dai.haruki@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In gfar_change_mtu(), the frame size needs to be increased to account
for the extra 4 bytes VLAN adds to the ethernet header.  However,
it was being increased by the length of the whole header (18 bytes),
which is wrong.
Signed-off-by: NDai Haruki <dai.haruki@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Buffer stashing parameter change to 96 from 64 in order to cover
the Layer 4 header.
Signed-off-by: NDai Haruki <dai.haruki@freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The code opening proc entry for each device makes the
same thing, as the single_open does, so remove the
unneeded code.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds support for BCM5481 PHY. Unfortunately it's hard to
get specifications for this PHY, so its special register 0x18 isn't
annotated properly (but we know it's used to set up the delays).

I've kept the magic numbers, so we'll not forget to fix it at the
first opportunity, and will name that register and its bits correctly.

p.s. also fixed the line with broken indention, introduced by
commit 03157ac3
    PHYLIB: Add BCM5482 PHY support
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Convert byte order of constant instead of variable which can be done at
compile time (vs run time)
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Robert P.J. Day proposed to use the macro FIELD_SIZEOF in replace of code
that matches its definition.

The modification was made using the following semantic patch
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
type t;
identifier f;
@@

- (sizeof(((t*)0)->f))
+ FIELD_SIZEOF(t, f)

@depends on haskernel@
type t;
identifier f;
@@

- sizeof(((t*)0)->f)
+ FIELD_SIZEOF(t, f)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds support for the IDT rc32434 Ethernet MAC
we can find in the IDT boards and the Mikrotik RB500.
Driver references some code from the linux-mips RB500
support.
Signed-off-by: NFlorian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NPhilip Rischel <rischelp@idt.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This timer doesn't need to run at precise times, so round it to a whole
second to decrease wakeups.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

missed read*/write* plus a bunch of wrong-sized ones...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

isa_bus_to_virt() is the wrong thing to do here; it happens
to work on i386, but only by accident.  What we want is
normal ioremap/readb/etc. set - it's all in iomem.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

take iscp-based testing into helper, kill the loop, stop
wanking with reassignments of priv->iscp
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* initialize spinlock once
* check586() used to be done before we'd allocated ->priv; these days
  it's there from the very beginning, so we don't have to play with
  private copy.  Consequently, we don't need to mess with reinitializing
  ->base, etc. afterwards.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

... and store the virt address where we map the ->mem_addr, while we
are at it.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Passing ISA bus address explicitly cast to char * only to cast it back to
unsigned long is dumb; so's passing it at all when it's always dev->mem_start...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

unsigned short != u8, it's u16...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Driver is still broken, though; partially from Alan's checkpatch-induced
fun, partially from layers of ancient mess ;-)

By the end of the series... hell, might be even worth trying to stick
such card into old alpha or ppc with an ISA slot and see if it work -
would be for the first time ever in case of alpha and for the first
time since at least 2.5.3 in case of ppc...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ixgb can remove irq_sem by auditing all the call sites to make sure
that each of them makes sure the adapter is in the correct state
before re-enabling interrupts.  after doing this to all of our other
drivers it is becoming easier.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

irq_sem was just a hack to prevent interrupts from being enabled
unexpectedly in deep call paths.  Simply finding those call paths and
fixing them by hand results in a driver that behaves as we expect and
doesn't need the atomic at all.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

irq_sem can safely be removed by auditing all irq.*able sites to
make sure that interrupts don't get enabled unexpectedly when the
interface is down.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This function is no longer used now that 82573 uses the eerd
read method as well. Thanks to Adrian Bunk for pointing this out.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

> send me a patch for e1000 and for ixgb and I'll happily apply those :)

boolean_t to bool
TRUE to true
FALSE to false
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In order to remove the irq_sem code we need to implement strict
adapter state checking to prevent accidental double up or downs
or resets. This code is largely copied from e1000/e1000e.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On Thu, 2008-03-06 at 10:07 -0800, Kok, Auke wrote:
> send me a patch for e1000 and for ixgb and I'll happily apply those :)

boolean_t to bool
TRUE to true
FALSE to false
comment typo ahread to ahead
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Optimize call routing between NATed endpoints: when an external
registrar sends a media description that contains an existing RTP
expectation from a different SNATed connection, the gatekeeper
is trying to route the call directly between the two endpoints.

We assume both endpoints can reach each other directly and
"un-NAT" the addresses, which makes the media stream go between
the two endpoints directly.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for multiple media channels and use it to create
expectations for video streams when present.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SDP connection addresses may be contained in the payload multiple
times (in the session description and/or once per media description),
currently only the session description is properly updated. Split up
SDP mangling so the function setting up expectations only updates the
media port, update connection addresses from media descriptions while
parsing them and at the end update the session description when the
final addresses are known.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create expectations for the RTCP connections in addition to RTP connections.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>