It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.

Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path.  Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.

OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch allows the UART clocks to be disabled when the OMAP UARTs
are inactive, thus permitting the chip to hit retention in idle.
After the expiration of an activity timer, each UART is allowed to
disable its clocks so the system can enter retention.  The activity
timer is (re)activated on any UART interrupt, UART wake event or any
IO pad wakeup.  The actual disable of the UART clocks is done in the
'prepare_idle' hook called from the OMAP idle loop.

While the activity timer is active, the smart-idle mode of the UART is
also disabled.  This is due to a "feature" of the UART module that
after a UART wakeup, the smart-idle mode may be entered before the
UART has communicated the interrupt, or upon TX, an idle mode may be
entered before the TX FIFOs are emptied.

Upon suspend, the 'prepare_suspend' hook cancels any pending activity
timers and allows the clocks to be disabled immediately.

In addition, upon disabling clocks the UART state is saved in case
of an off-mode transition while clocks are off.

Special thanks to Tero Kristo for the initial ideas and first versions
of UART idle support, and to Jouni Hogander for extra testing and
bugfixes.

Tested on OMAP3 (Beagle, RX51, SDP, EVM) and OMAP2 (n810)

Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds common function to enable/disable omap2/3 uart
clocks. Enabled uarts are passed by bootloader in atags and clocks for
these enabled uarts are touched.
Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Make is_omap_port() take the uart_8250_port structure so it can do
whatever test it desires.  Convert the test to compare the physical
addresses rather than virtual addresses.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Tony Lindgren

This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Start adding 24xx support by Paul Mundt
- Clean-up of cpu detection by Dirk Behme and Tony Lindgren
- Add DSP header by Toshihiro Kobayashi
- Add support for mtd-xip by Vladimir Barinov
- Add various new mux registers
- Move OMAP specific serial defines back to serial.h
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>