A couple of operations, the flushes and the tracepoint, do not require
serialisation by client->wq_lock, so move them before we take it.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228112803.11646-3-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Following the use of dma_fence_signal() from within our interrupt
handler, we need to make guc->wq_lock also irq-safe. This was done
previously as part of the guc scheduler patch (which also started
mixing our fences with the interrupt handler), but is now required to
fix the current guc submission backend.

v4: Document that __i915_guc_submit is always under an irq disabled
section
v5: Move wq_rsvd adjustment to its own function

Fixes: 67b807a8 ("drm/i915: Delay disabling the user interrupt for breadcrumbs")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228112803.11646-2-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

On some devices only MIPI PORT C is used, in this case checking the
MIPI PORT A CTRL AFE_LATCHOUT bit (there is no such bit for PORT C
on VLV/CHT) will result in false positive "DSI LP not going Low" errors
as this checks the PORT A clk status.

In case both ports are used we have already checked the AFE_LATCHOUT
bit when going through the for_each_dsi_port() loop for PORT A and
checking the same bit again for PORT C is a no-op.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97061Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/242e4438bf29ebffc66eaa182f22b9d60d304bc2.1488273823.git.jani.nikula@intel.com

The drm_panel_enable/disable and drm_panel_prepare/unprepare calls are
not fine grained enough to abstract all the different steps we need to
take (and VBT sequences we need to exec) properly. So simply remove the
panel _enable/disable and prepare/unprepare callbacks and instead
export intel_dsi_exec_vbt_sequence() from intel_dsi_panel_vbt.c
and call that from intel_dsi_enable/disable().

No functional changes.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/b4ca5185d4788d92df2ed60837a24b8962a8e8ba.1488273823.git.jani.nikula@intel.com

Move the intel_dsi_clear_device_ready() function to higher up in
intel_dsi.c this pairs it with intel_dsi_device_ready(); and pairs
intel_dsi_*enable* with intel_dsi_*disable without
intel_dsi_clear_device_ready() sitting in the middle of them.

This commit purely moves code around, it does not make any
changes what-so-ever.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/f971d18ea6d350890447860aeb541dba072a6e47.1488273823.git.jani.nikula@intel.com

The enable path has an intel_dsi_prepare() helper which prepares various
registers for the mode-set. Move the code undoing this to a new
intel_dsi_unprepare() helper function for better symmetry between the
enable and disable paths. No functional changes.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/cc0baaf04ea74a20031b4b5bb128591dcfa78406.1488273823.git.jani.nikula@intel.com

intel_dsi_disable/enable only have one caller, merge them into their
respective callers.

Change msleep(2) into usleep_range(2000, 5000) to make checkpatch happy,
otherwise no functional changes.

The main advantage of this change is that it makes it easier to
follow all the steps of the panel enable / disable sequence when
reading the code.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/d7249612e6d2e9639ecd1d8d106ca37d5794f2a4.1488273823.git.jani.nikula@intel.com

Instead of calling wait_for_dsi_fifo_empty on all dsi ports after calling
a drm_panel_foo helper which calls VBT sequences, move it to the VBT
mipi_exec_send_packet helper, which is the one VBT instruction which
actually puts data in the fifo.

This results in a nice cleanup making it clearer what all the steps on
intel_dsi_enable / disable are and this also makes the VBT code properly
wait till a command has actually been send before executing the next
steps (typically a delay) in the VBT sequence.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/289977b5699e252fea5c211d1d1645f9e79cca79.1488273823.git.jani.nikula@intel.com

Move the setting of gpu_error->missed_irq_ring bit to a common function
so that we can get the debug logging for either path.

v2: Add %pF caller
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170228085018.3225-1-chris@chris-wilson.co.uk

As per BSPEC, GLK supports MIPI DSI 8X clk only on PORT A.
Therefore only for PORT A PLL divider value should be validated.
Signed-off-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-8-git-send-email-madhav.chauhan@intel.com

v2: Addressed Jani's Review comments(renamed bit field macros)

Txesc clock divider is calculated and programmed
for geminilake platform.
Signed-off-by: NDeepak M <m.deepak@intel.com>
Signed-off-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-7-git-send-email-madhav.chauhan@intel.com

Register MIPI_CLOCK_CTRL is applicable only
for BXT platform. Future platform have other
registers to program the escape clock dividers.
Signed-off-by: NDeepak M <m.deepak@intel.com>
Signed-off-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-6-git-send-email-madhav.chauhan@intel.com

PLL divider range for GLK is different than that of
BXT, hence adding the GLK range check in this patch.

v2: Code restructure using min and max ratio variables (Ander)
v3: Code changes to avoid "maybe-uninitialized" warning (Jani)
Signed-off-by: NDeepak M <m.deepak@intel.com>
Signed-off-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-5-git-send-email-madhav.chauhan@intel.com

Program the clk lane and tlpx time count registers
to configure DSI PHY.

v2: Addressed Jani's Review comments(renamed bit field macros)
v3: Program clk lane timing reg same as dphy param reg.
v4: Removed "line over 80 character" warning
Signed-off-by: NDeepak M <m.deepak@intel.com>
Signed-off-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-3-git-send-email-madhav.chauhan@intel.com

For GEMINILAKE, dphy param reg values are programmed in terms
of HS byte clock count while for older platforms in terms of
HS ddr clk count.

v2: Added comments to clarify ddr clock count calculation
v3: Use multiplier variable instead of IS_GEMINILAKE()
check everywhere (Jani)
Signed-off-by: NDeepak M <m.deepak@intel.com>
Signed-off-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-2-git-send-email-madhav.chauhan@intel.com

A significant cost in setting up a wait is the overhead of enabling the
interrupt. As we disable the interrupt whenever the queue of waiters is
empty, if we are frequently waiting on alternating batches, we end up
re-enabling the interrupt on a frequent basis. We do want to disable the
interrupt during normal operations as under high load it may add several
thousand interrupts/s - we have been known in the past to occupy whole
cores with our interrupt handler after accidentally leaving user
interrupts enabled. As a compromise, leave the interrupt enabled until
the next IRQ, or the system is idle. This gives a small window for a
waiter to keep the interrupt active and not be delayed by having to
re-enable the interrupt.

v2: Restore hangcheck/missed-irq detection for continuations
v3: Be more careful restoring the hangcheck timer after reset
v4: Be more careful restoring the fake irq after reset (if required!)
v5: Redo changes to intel_engine_wakeup()
v6: Factor out __intel_engine_wakeup()
v7: Improve commentary for declaring a missed wakeup
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227205850.2828-4-chris@chris-wilson.co.uk

By deferring hangcheck to the fake breadcrumb interrupt, we can simply
the enabling procedure slightly - as by enabling the fake, we then
enable the hangcheck. By always enabling the hangcheck from each fake
interrupt (it will be a no-op for an already queued hangcheck), it will
make restoring the breadcrumbs after a reset simpler in the next patch.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227205850.2828-3-chris@chris-wilson.co.uk

As execlists and other non-semaphore multi-engine devices coordinate
between engines using interrupts, we can shave off a few 10s of
microsecond of scheduling latency by doing the fence signaling from the
interrupt as opposed to a RT kthread. (Realistically the delay adds
about 1% to an individual cross-engine workload.) We only signal the
first fence in order to limit the amount of work we move into the
interrupt handler. We also have to remember that our breadcrumbs may be
unordered with respect to the interrupt and so we still require the
waiter process to perform some heavyweight coherency fixups, as well as
traversing the tree of waiters.

v2: No need for early exit in irq handler - it breaks the flow between
patches and prevents the tracepoint
v3: Restore rcu hold across irq signaling of request
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227205850.2828-2-chris@chris-wilson.co.uk

The two users of the return value from intel_engine_wakeup() are
expecting different results. In the breadcrumbs hangcheck, we are using
it to determine whether wake_up_process() detected the waiter was
currently running (and if so we presume that it hasn't yet missed the
interrupt). However, in the fake_irq path, we are using the return value
as a check as to whether there are any waiters, and so we may
incorrectly stop the fake-irq if that waiter was currently running.

To handle the two different needs, return both bits of information! We
uninline it from the irq path in preparation for the next patch which
makes the irq hotpath special and relegates intel_engine_wakeup() to the
slow fixup paths.

v2: s/ret/result/
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227205850.2828-1-chris@chris-wilson.co.uk

After initiating a sideband transaction, we only want to wait for the
transaction to become idle. If, as we are, we wait for both the busy
and error flag to clear, if an error is raised we just spin until the
timeout. Once the hw is idle, we can then check to see if the hw flagged
an error, and report it distinctly.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170223141020.13250-1-chris@chris-wilson.co.ukReviewed-by: NJani Nikula <jani.nikula@intel.com>

No hardware was ever shipped that needed more than 4096 byte alignment
and future hardware will not use this legacy path. So reduce the
alignment to make it easier and quicker to launch workloads.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227135913.8056-3-chris@chris-wilson.co.uk

We are required to reload the TLBs around ppgtt switches. However, we
already do an unconditional TLB invalidate before every batch and a flush
afterwards, so this condition is already satisfied without extra flushes
around the LRI instructions.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227135913.8056-2-chris@chris-wilson.co.uk

We are required to reload the TLBs around context switches
(MI_SET_CONTEXT specifically) and the recommendation is do that before
the MI_SET_CONTEXT so that it is serialised with the switch and not
forgotten:

[DevSNB] If Flush TLB invalidation Mode is enabled it’s the driver’s
responsibility to invalidate the TLBs at least once after the previous
context switch after any GTT mappings changed (including new GTT entries).
This can be done by a pipeline PIPE_CONTROL with TLB inv bit set
immediately before MI_SET_CONTEXT.

However, we already do an unconditional TLB invalidate before every
batch so this condition is satifisfied.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227135913.8056-1-chris@chris-wilson.co.uk

Certain Baytrails, namely the 4 cpu core variants, have been
plaqued by spurious system hangs, mostly occurring with light loads.

Multiple bisects by various people point to a commit which changes the
reclocking strategy for Baytrail to follow its bigger brethen:
commit 8fb55197 ("drm/i915: Agressive downclocking on Baytrail")

There is also a review comment attached to this commit from Deepak S
on avoiding punit access on Cherryview and thus it was excluded on
common reclocking path. By taking the same approach and omitting
the punit access by not tweaking the thresholds when the hardware
has been asked to move into different frequency, considerable gains
in stability have been observed.

With J1900 box, light render/video load would end up in system hang
in usually less than 12 hours. With this patch applied, the cumulative
uptime has now been 34 days without issues. To provoke system hang,
light loads on both render and bsd engines in parallel have been used:
glxgears >/dev/null 2>/dev/null &
mpv --vo=vaapi --hwdec=vaapi --loop=inf vid.mp4

So far, author has not witnessed system hang with above load
and this patch applied. Reports from the tenacious people at
kernel bugzilla are also promising.

Considering that the punit access frequency with this patch is
considerably less, there is a possibility that this will push
the, still unknown, root cause past the triggering point on most loads.

But as we now can reliably reproduce the hang independently,
we can reduce the pain that users are having and use a
static thresholds until a root cause is found.

v3: don't break debugfs and simplification (Chris Wilson)

References: https://bugzilla.kernel.org/show_bug.cgi?id=109051
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: fritsch@xbmc.org
Cc: miku@iki.fi
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
CC: Michal Feix <michal@feix.cz>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.2+
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487166779-26945-1-git-send-email-mika.kuoppala@intel.com

As we track whether a vma has been inserted into the drm_mm using the
vma->flags, if we fail to bind the vma into the GTT we do not update
those bits and will attempt to reinsert the vma into the drm_mm on
future passes. To prevent that, we want to unwind i915_vma_insert() if
we fail in our attempt to bind.

Fixes: 59bfa124 ("drm/i915: Start passing around i915_vma from execbuffer")
Testcase: igt/drv_selftest/live_gtt
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227122654.27651-3-chris@chris-wilson.co.uk

If we fail to allocate the ppgtt range after allocating the pages for
the vma, we should unwind the local allocation before reporting back the
failure.

Fixes: ff685975 ("drm/i915: Move allocate_va_range to GTT")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227122654.27651-2-chris@chris-wilson.co.uk

Only if we allocated the layer and the lower level failed should we
remove this layer when unwinding. Otherwise we ignore the overlapping
entries by overwriting the old layer with scratch.

Fixes: c5d092a4 ("drm/i915: Remove bitmap tracking for used-pml4")
Fixes: e2b763ca ("drm/i915: Remove bitmap tracking for used-pdpes")
Reported-by: NMatthew Auld <matthew.william.auld@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99947
Testcase: igt/drv_selftest/live_gtt
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Tested-by: NMatthew Auld <matthew.auld@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227122654.27651-1-chris@chris-wilson.co.uk

The replay bit of the ring mode register is not a valid bit for Gen8+.
Do not write to this bit.
Signed-off-by: NKelvin Gardiner <kelvin.gardiner@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Ceraolo Spurio, Daniele <daniele.ceraolospurio@intel.com>
Reviewed-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
[Joonas: Fixed commit message line to be under 72 chars]
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487963724-4824-1-git-send-email-kelvin.gardiner@intel.com

Used by production device:
    Intel(R) Iris(TM) Graphics P555

Cc: <stable@vger.kernel.org>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NMichał Winiarski <michal.winiarski@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170227112256.20060-1-michal.winiarski@intel.com

Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

According to bspec, the DDI IO power domains should be enabled after
enabling the DPLL and mapping it to the DDI. The current order doesn't
seem to create problems with Skylake and Kabylake, but causes enable
timeouts in Geminilake.

v2: Rebase.
  - Take power domain references before sanitizing encoders. (Imre)
  - Add comment to get_encoder_power_domains() defition. (Ander)

v3: Don't put the domain if called with HSW/BDW's analog encoder. (CI)

v4: Put IO power domain before unmapping DPLL. (Imre)
  - Change return type of intel_ddi_get_power_domains() to u64. (Imre)

Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com> # v1
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224141959.5955-1-ander.conselvan.de.oliveira@intel.com

In Geminilake, the DDI IO power domains can't be enabled before a DPLL
is running and mapped to the appropriate DDI. At least on Geminilake,
attempting to enable those during init will lead to a timeout.

The failure to enable the power domain also causes issues with the state
verifier during resume from suspend. After all the init power domains
are enabled, the call to intel_power_domains_sync_hw() from the resume
path will cause the hw_enabled field on the respective power wells to be
false while the usage count remains above zero. Further attempts to
enable the power domain caused by a modeset will simply update the usage
count without doing anything else. When the state verifier attempts to
read the state of a DDI encoder, intel_display_power_get_if_enabled()
returns false, leading to the following WARN:

WARNING: CPU: 3 PID: 1743 at drivers/gpu/drm/i915/intel_display.c:7001 verify_connector_state.isra.80+0x26c/0x2b0 [i915]
attached crtc is active, but connector isn't
Modules linked in: i915(E) tun ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_broute bridge stp llc ebtable_nat ip6table_mangle ip6table_security ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_raw iptable_mangle iptable_security iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_raw ebtable_filter ebtables ip6table_filter ip6_tables x86_pkg_temp_thermal coretemp kvm_intel kvm i2c_algo_bit drm_kms_helper irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel drm shpchp tpm_tis tpm_tis_core tpm nfsd auth_rpcgss nfs_acl lockd grace sunrpc crc32c_intel serio_raw [last unloaded: i915]
CPU: 3 PID: 1743 Comm: kworker/u8:22 Tainted: G        W   E   4.10.0-rc3ander+ #300
Hardware name: Intel Corp. Geminilake/GLK RVP1 DDR4 (05), BIOS GELKRVPA.X64.0023.B40.1611302145 11/30/2016
Workqueue: events_unbound async_run_entry_fn
Call Trace:
 dump_stack+0x86/0xc3
 __warn+0xcb/0xf0
 warn_slowpath_fmt+0x5f/0x80
 verify_connector_state.isra.80+0x26c/0x2b0 [i915]
 intel_atomic_commit_tail+0x520/0x1000 [i915]
 ? remove_wait_queue+0x70/0x70
 intel_atomic_commit+0x3f8/0x520 [i915]
 ? intel_runtime_pm_put+0x6e/0xa0 [i915]
 drm_atomic_commit+0x4b/0x50 [drm]
 __intel_display_resume+0x72/0xc0 [i915]
 intel_display_resume+0x107/0x150 [i915]
 i915_drm_resume+0xe0/0x180 [i915]
 i915_pm_restore+0x1e/0x30 [i915]
 i915_pm_resume+0xe/0x10 [i915]
 pci_pm_resume+0x64/0xa0
 dpm_run_callback+0xa1/0x2a0
 ? pci_pm_thaw+0x90/0x90
 device_resume+0xe3/0x200
 async_resume+0x1d/0x50
 async_run_entry_fn+0x39/0x170
 process_one_work+0x212/0x670
 ? process_one_work+0x197/0x670
 worker_thread+0x4e/0x490
 kthread+0x101/0x140
 ? process_one_work+0x670/0x670
 ? kthread_create_on_node+0x60/0x60
 ret_from_fork+0x2a/0x40

Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222063431.10060-6-ander.conselvan.de.oliveira@intel.com

Implement WaDDIIOTimeout to avoid a timeout when enabling the DDI IO
power domains.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222063431.10060-5-ander.conselvan.de.oliveira@intel.com

Don't allow conversion from arbitraty encoder types to a digital port.
Calling enc_to_dig_port() with the wrong encoder may seem far fetched,
but certain paths of the ddi code may be called with hasell's analog
encoder and the conversion is wrong for DP mst encoders too, so safe
guard against it.

v2: Warn if encoder type is unknown and device is not DDI. (Imre)
v3: Remove stray hunk from rebase error. (Ander)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224141845.5836-1-ander.conselvan.de.oliveira@intel.com

The encoder power domain is obviously tied to the encoder, so store it
in struct intel_encoder. This avoids some indirection.

v2: Rebase
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222063431.10060-3-ander.conselvan.de.oliveira@intel.com

The aux power domain only makes sense in the DP code. Storing it in
struct intel_dp avoids some indirection.

v2: Rebase
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222063431.10060-2-ander.conselvan.de.oliveira@intel.com

When advancing onto the next 4th level page table entry, we need to
reset our indices to 0. Currently we restart from the original address
which means we start with an offset into the next PML table.

Fixes: 894ccebe ("drm/i915: Micro-optimise gen8_ppgtt_insert_entries()")
Reported-by: NMatthew Auld <matthew.william.auld@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99948
Testcase: igt/drv_selftest/live_gtt
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Tested-by: NMatthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: NMatthew Auld <matthew.william.auld@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170225181122.4788-4-chris@chris-wilson.co.uk

We rely on the VMA being allocated inside the drm_mm and for its allotted
node being large enough to accommodate all the vma->pages.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: NMatthew Auld <matthew.william.auld@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170225181122.4788-3-chris@chris-wilson.co.uk

Before looking up the page directory entry, check we are still within
bounds.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: NMatthew Auld <matthew.william.auld@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170225181122.4788-2-chris@chris-wilson.co.uk

Double check that we allocated the right amount of scatterlist elements
for our obj->size.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: NMatthew Auld <matthew.william.auld@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170225181122.4788-1-chris@chris-wilson.co.uk