Add MT26438 (ConnectX EN 40GigE PCIe 2.0 5GT/s) to the list of supported
devices.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ConnectX can work more efficiently if the CPU cache line size is passed
to it with the INIT_HCA firmware command.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

catas_reset() uses pointer to mlx4_priv, but mlx4_priv is not valid
after call mlx4_restart_one().
Signed-off-by: NVitaliy Gusev <vgusev@openvz.org>
Acked-by: NRoland Dreier <rolandd@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the mlx4 driver uses the same name for interrupts for every
device in the system.  This can make it very confusing trying to work
out exactly which device MSI-X interrupts are for.  Change the driver
to add the PCI name of the device to the interrupt name.
Signed-off-by: NArputham Benjamin <abenjamin@sgi.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

On the error path of mlx4_init_hca(), mlx4_close_hca() is called,
followed by mlx4_free_icms() and mlx4_UNMAP_FA().  But both those
functions are also called from mlx4_close_hca(), which leads to a
double free.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The current implementation allocates a single host page for EQ context
memory, which was OK when we only allocated a few EQs.  However, since
we now allocate an EQ for each CPU core, this patch removes the
hard-coded limit (which we exceed with 4 KB pages and 128 byte EQ
context entries with 32 CPUs) and uses the same ICM table code as all
other context tables, which ends up simplifying the code quite a bit
while fixing the problem.

This problem was actually hit in practice on a dual-socket Nehalem box
with 16 real hardware threads and sufficiently odd ACPI tables that it
shows on boot

    SMP: Allowing 32 CPUs, 16 hotplug CPUs

so num_possible_cpus() ends up 32, and mlx4 ends up creating 33 MSI-X
interrupts and 33 EQs.  This mlx4 bug means that mlx4 can't even
initialize at all on this quite mainstream system.

Cc: <stable@kernel.org>
Reported-by: NEli Cohen <eli@mellanox.co.il>
Tested-by: NChristoph Lameter <cl@linux-foundation.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Lots of mlx4 files with no function annotations included <linux/init.h>
for no reason.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The old code used two calls to pci_request_region() to get the two BARs
for the mlx4 device, for no particularly good reason.  Clean up the code
a little by converting this to a single call to pci_request_regions().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In a couple of cases collapse some extra code like:
   int retval = NETDEV_TX_OK;
   ...
   return retval;
into
   return NETDEV_TX_OK;
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NETPOLL API requires that interrupts remain disabled in
netpoll_send_skb(). The use of "A functions set" in the NETPOLL API
callbacks causes the interrupts to get enabled and can lead to kernel
instability.

The solution is to use "B functions set" to prevent the irqs from
getting enabled while in netpoll_send_skb().

A functions set:
local_irq_disable()/local_irq_enable()
spin_lock_irq()/spin_unlock_irq()
spin_trylock_irq()/spin_unlock_irq()

B functions set:
local_irq_save()/local_irq_restore()
spin_lock_irqsave()/spin_unlock_irqrestore()
spin_trylock_irqsave()/spin_unlock_irqrestore()
Signed-off-by: NDongdong Deng <dongdong.deng@windriver.com>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the length is less or equal to frag_prefix_size in the first iteration
we write skb_frags_rx[-1] and read from priv->frag_info[-1]
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We use 1:1 mapping between QPs and SRQs on receive side,
so additional indirection level not required. Allocated the receive
buffers for the RSS QPs.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no point in using more QPs then actual number of receive rings.
If the RSS function for two streams gives the same result modulo number
of rings, they will arrive to the same RX ring anyway.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the net device is identified as "sender" (number of sent packets
is higher then the number of received packets and the incoming packets are
small), set the moderation time to its low limit.
We do it because the incoming packets are acks, and we don't want to delay them
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In cases of fragmented skb, with the data pointers being wrapped around
the TX buffer, the completion handling code would not forward the data
pointer and the firs fragment was unmapped several times, while others
were not unmapped at all.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The values in the advertising field are typically ADVERTISED_xxx, not
SUPPORTED_xxx.  Both SUPPORTED_10000baseT_Full and
ADVERTISED_1000baseT_Full have the same value.

The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct ethtool_cmd E;
@@
*E.advertising = SUPPORTED_10000baseT_Full
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

MT26468 (PCI ID 0x6764) devices can expose multiple physical
functions.  The current driver only handles the primary physical
function.  For other functions, the QUERY_FW firmware command will
fail with the CMD_STAT_MULTI_FUNC_REQ error code.  Don't try to drive
such devices, but print a message saying the driver is skipping those
devices rather than just "QUERY_FW command failed."
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>

[ Rather than keeping unsupported devices bound to the driver, simply
  print a more informative error message and exit - Roland ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.

Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 5d23a1d2 ("net: replace dma_sync_single with
dma_sync_single_for_cpu") replaced uses of the deprectated function
dma_sync_single() with calls to dma_sync_single_for_cpu().  However,
to be correct, the code should do a sync for_cpu() before touching the
memory and for_device() after it's done.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Our RX rings are always full, there is no need to check whether
we need to fill them or not. If we fail to allocate a new socket
buffer, the incoming packet is dropped an the ring remains full.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This check that verifies that the LSO header along with control
segment and first data segment do not cross 128 bytes is no longer
required.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When closing the port, we stop all transmit queues under the transmit
lock. It ensures that we will not attempt to transmit new packets after
the physical port was closed.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After we moved to be a multi queue device, need to stop/start
all of our transmit queues.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't need this check in the transmit function
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reporting the counter's value through 'ethtool -S'
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice.  Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.  This is the same bug that was reported in ib_mthca by Yinghai
Lu <yhlu.kernel@gmail.com>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

trivial: fix typos s/paramter/parameter/ and s/excute/execute/ in documentation and source comments.
Signed-off-by: NMartin Olsson <martin@minimum.se>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

If mlx4_create_eq() would fail for one of EQ's assigned for
completion handling, the code would try to free the same EQ
we failed to create.
The crash was found by Christoph Lameter
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default the driver opens 8 TX queues (defined by MLX4_EN_NUM_TX_RINGS).
If the driver is configured to support Per Priority Flow Control, we open
8 additional TX rings.
dev->real_num_tx_queues is always set to be MLX4_EN_NUM_TX_RINGS.
The mlx4_en_select_queue() function uses standard hashing (skb_tx_hash)
in case that PPFC is not supported or the skb contain a vlan tag,
otherwise the queue is selected according to vlan priority.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupt moderation should not depend on number of incoming
bytes, but on number of incoming packets.
The previous scheme caused very high interrupts rate for small
messages when big MTU was configured.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the initialization of one of the ports failed,
there is no need to fail the other one as well.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

en_params.c file now only handles Ethtool functionality
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For each debug message, the message will show interface name in case
that the net device was registered, and PCI bus ID with port number
if we were not registered yet. Messages that are not port/netdev specific
stayed in the old format
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the transmit queue gets full we enable interrupts for TX completions
There was a race that we handled the TX queue both from the interrupt context
and from the transmit function. Using "spin_trylock_irq()" ensures this
doesn't happen.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This replaces dma_sync_single() with dma_sync_single_for_cpu() because
dma_sync_single() is an obsolete API; include/linux/dma-mapping.h says:

/* Backwards compat, remove in 2.7.x */
#define dma_sync_single		dma_sync_single_for_cpu
#define dma_sync_sg		dma_sync_sg_for_cpu
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>