Add MT26438 (ConnectX EN 40GigE PCIe 2.0 5GT/s) to the list of supported
devices.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Commit d43c36dc ("headers: remove
sched.h from interrupt.h") left some build errors in some configurations
due to drivers having depended on getting header files "accidentally".
Signed-off-by: NIngo Molnar <mingo@elte.hu>
[ Combined several one-liners from Ingo into one single patch  - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Only 128 buffer descriptors are supported in the core. Limit the
number in case we have more memory.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enabled the ethoc to allocate system memory as buffer
when there is no dedicated buffer memory.

Some hardware designs may not have dedicated buffer memory such as
on chip or off chip SRAM. In this case, only one memory resource is
supplied in the platform data instead of two. Then a DMA buffer can
be allocated from system memory and used for the transfer.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The packet buffer is allocated at 4 bytes boundary, but the IP header
length and version bits is located at byte 14. These bit fields access
as 32 bits word and caused exception on processors that do not support
unaligned access.

The patch adds 2 bytes offset to make the bit fields word aligned.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pointer address in buffer descriptors is physical address. The
pointer that processor used to access packet is virtual address.

Though the higher bits of pointer address used by the MAC may be
truncated to zero in special case, it is not always true in larger
designs.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It should be max() instead of min(). Use 1/4 of available
descriptors for tx, and there should be at least 2 tx
descriptors.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

in update_rx_stats() the RX_OVERLEN bit is set twice, replace it by RX_RUNT.
in au1000_rx() the RX_MISSED_FRAME bit was tested a few lines earlier already
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The closing parenthesis was not on the right location.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all pasemi mac interfaces can have a phy attached.
For example, XAUI has no phy and phydev is NULL for it.
In this case ethtool get settings causes kernel crash.
Fix it by returning -EOPNOTSUPP if there's no PHY attached.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Felix Radensky noted that chip resets were generating stack trace dumps.
This is because the driver is attempting to acquire the mdio bus mutex
while holding the tp->lock spinlock.  The fix is to change the code such
that every phy access takes the tp->lock spinlock instead.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a fix for a bug which was a result of wrong use of checksum offload flag.
The status of tx-checksumming was not changed from on to off
after a 'ethtool -K <ifname> tx off' operation.
Use the proper checksum offload flag NETIF_F_HW_CSUM instead of
NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM.
Patch is against net-2.6 tree.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66.
This patch fixes this typo. Patch against net-2.6 tree.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While updating the statistics to be passed via the get_stats,
tx multicast frames were being accounted instead of rx multicast frames.
This patch fixes the bug. This patch is against the net-2.6 tree.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of spinlock and private mutex usage for exclusive access to the
HW semaphore register.  rtnl_lock already creates exclusive access to
this register in all driver API.
Add rtnl to firmware worker threads that also use the HW semaphore register.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check that we are not already polling firmware events before we queue the
firmware event worker, then disable firmware interrupts.
Otherwise we can queue the same event multiple times.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug that got introduced in commit 76998bc7.
During preparation of mcc wrb, req was being wrongly overwritten
and the flash operation was failing.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pcnet_cs,serial_cs:
  
add cis of National Semicondoctor's lan&modem mulitifunction pcmcia card,
NE2K, tamarack ethernet card,
and some serial card(COMpad2, COMpad4).
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There appears to have been a mixup in the max supported jumbo frame size
between 82574 and 82583 which ended up disabling jumbo frames on the 82574
as a result.  This patch swaps the two so that this issue is resolved.

This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=14261Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds device support for the 82599 based X520 10GbE
Dual Port KX4 Mezzanine card.

Signed-off-by: Don Skidmore<donald.c.skidmore@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch will add support for the 82599 Dual port Backplane
device (0x10f8).  This device has the ability to link in serial (KR) and
parallel (KX4/KX) modes, depending on what the switch capabilities are in
the blade chassis.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the problem of not handling the NETDEV_UP event properly
during hot-plug or modprobe of bnx2 after cnic.  The handling was
skipped by mistakenly using "else if" to check for the event.

Also update version to 2.0.1.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only error returned by pci_{en,dis}able_pcie_error_reporting() is
-EIO which simply means that Advanced Error Reporting is not supported.
There is no need to report that, so remove the error check from e1000e,
igb and ixgbe.
Signed-off-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Which is why I have always preferred sizeof(struct foo) over
sizeof(var).
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is based on Michal Schmidt fix for skge.

Most network drivers request their IRQ when the interface is activated.
sky2 does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:

1. modprobe sky2
   The card is detected as eth0 and requests IRQ 17. Directory
   /proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
   eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
   The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
   Now 8139too requests IRQ 17.

The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered

The fix is for sky2 to name the irq based on the pci device, as is done
by some other devices DRM, infiniband, ...  ie. sky2@pci:0000:00:00
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Reviewed-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most network drivers request their IRQ when the interface is activated.
skge does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:

1. modprobe skge
   The card is detected as eth0 and requests IRQ 17. Directory
   /proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
   eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
   The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
   Now 8139too requests IRQ 17.

The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
...
And "ls /proc/irq/17" shows two subdirectories, both called eth0.

Fix it by using a unique name for skge's IRQ, based on the PCI address.
The naming from the example then looks like this:
$ grep skge /proc/interrupts
 17:        169   IO-APIC-fasteoi   skge@pci:0000:00:0a.0, eth0

irqbalance daemon will have to be taught to recognize "skge@" as an
Ethernet interrupt. This will be a one-liner addition in classify.c. I
will send a patch to irqbalance if this change is accepted.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove references to dead web site mosquitonet.Stanford.EDU.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This typo was introduced by 5793f4be on
October 14, 2005 ...
Reported-by: NMatti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

prev_vlan_tag field is not used.

Patch saves 512*8 bytes per tx queue ring on 64bit arches.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NMatthew Carlson <mcarlson@broadcom.com>

The function virtnet_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alex Williamson <alex.williamson@hp.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function sgiseeq_remove is defined using __exit, so don't use
__devexit_p but __exit_p to wrap it.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Wang Chen <wangchen@cn.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function meth_remove is defined using __exit, so don't use __devexit_p
but __exit_p to wrap it.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Primary module parameter passed to bonding is pernament. That means if you
release the primary slave and enslave it again, it becomes the primary slave
again. But if you set primary slave via sysfs, the primary slave is only set
once and it's not remembered in bond->params structure. Therefore the setting is
lost after releasing the primary slave. This simple one-liner fixes this.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ccffad25 changed parameters for function
ixgbe_update_uc_addr_list_generic but parameter description was not updated.
This patch corrects it.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vtp bit in RX completion descriptor could be wrongly set in
some skews of BladEngine.  Ignore this  bit if vtm is not set.
Resending because the previous patch was against net-next tree.
This patch is against the net-2.6 tree.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As noticed by Alan Stern, there is still one issue with the driver:
we disable PCI IRQ on suspend, but other devices on the same IRQ
line might still need the IRQ enabled to suspend properly.

Nowadays, PCI core handles all power management work by itself, with
one condition though: if we use dev_pm_ops. So, rework the driver to
only quiesce 3c59x internal logic on suspend, while PCI core will
manage PCI device power state with IRQs disabled.
Suggested-by: NRafael J. Wysocki <rjw@sisk.pl>
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>