ARM: sun4i: ba10 tvbox: Convert to DT label based syntax

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts

@@ -54,95 +54,93 @@
 / {
 	model = "BA10 tvbox";
 	compatible = "allwinner,ba10-tvbox", "allwinner,sun4i-a10";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_pins_a>;
+	phy = <&phy1>;
+	status = "okay";
+};
 
-	soc@01c00000 {
-		emac: ethernet@01c0b000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&emac_pins_a>;
-			phy = <&phy1>;
-			status = "okay";
-		};
-
-		mdio@01c0b080 {
-			status = "okay";
-
-			phy1: ethernet-phy@1 {
-				reg = <1>;
-			};
-		};
-
-		mmc0: mmc@01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
-			cd-inverted;
-			status = "okay";
-		};
-
-		usbphy: phy@01c13400 {
-			usb1_vbus-supply = <&reg_usb1_vbus>;
-			usb2_vbus-supply = <&reg_usb2_vbus>;
-			status = "okay";
-		};
-
-		ehci0: usb@01c14000 {
-			status = "okay";
-		};
-
-		ohci0: usb@01c14400 {
-			status = "okay";
-		};
-
-		ehci1: usb@01c1c000 {
-			status = "okay";
-		};
-
-		ohci1: usb@01c1c400 {
-			status = "okay";
-		};
-
-		pinctrl@01c20800 {
-			usb2_vbus_pin_a: usb2_vbus_pin@0 {
-				allwinner,pins = "PH12";
-			};
-		};
-
-		ir0: ir@01c21800 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&ir0_pins_a>;
-			status = "okay";
-		};
-
-		uart0: serial@01c28000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_pins_a>;
-			status = "okay";
-		};
-
-		i2c0: i2c@01c2ac00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins_a>;
-			status = "okay";
-
-			axp209: pmic@34 {
-				compatible = "x-powers,axp209";
-				reg = <0x34>;
-				interrupts = <0>;
-
-				interrupt-controller;
-				#interrupt-cells = <1>;
-			};
-		};
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	axp209: pmic@34 {
+		compatible = "x-powers,axp209";
+		reg = <0x34>;
+		interrupts = <0>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
 	};
+};
 
-	reg_usb1_vbus: usb1-vbus {
-		status = "okay";
+&ir0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir0_pins_a>;
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
 	};
+};
 
-	reg_usb2_vbus: usb2-vbus {
-		gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
-		status = "okay";
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+	cd-inverted;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	usb2_vbus_pin_a: usb2_vbus_pin@0 {
+		allwinner,pins = "PH12";
 	};
 };
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};