提交 84bdea6e 编写于 作者: M Maxime Ripard

ARM: sun4i: a1000: Convert to DT label based syntax

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
上级 903b2d75
...@@ -58,103 +58,6 @@ ...@@ -58,103 +58,6 @@
model = "Mele A1000"; model = "Mele A1000";
compatible = "mele,a1000", "allwinner,sun4i-a10"; compatible = "mele,a1000", "allwinner,sun4i-a10";
soc@01c00000 {
emac: ethernet@01c0b000 {
pinctrl-names = "default";
pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
mdio@01c0b080 {
phy-supply = <&reg_emac_3v3>;
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
mmc0: mmc@01c0f000 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
cd-inverted;
status = "okay";
};
usbphy: phy@01c13400 {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
ehci0: usb@01c14000 {
status = "okay";
};
ohci0: usb@01c14400 {
status = "okay";
};
ahci: sata@01c18000 {
status = "okay";
};
ehci1: usb@01c1c000 {
status = "okay";
};
ohci1: usb@01c1c400 {
status = "okay";
};
pinctrl@01c20800 {
emac_power_pin_a1000: emac_power_pin@0 {
allwinner,pins = "PH15";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
led_pins_a1000: led_pins@0 {
allwinner,pins = "PH10", "PH20";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
ir0: ir@01c21800 {
pinctrl-names = "default";
pinctrl-0 = <&ir0_pins_a>;
status = "okay";
};
uart0: serial@01c28000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
i2c0: i2c@01c2ac00 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupts = <0>;
interrupt-controller;
#interrupt-cells = <1>;
};
};
};
leds { leds {
compatible = "gpio-leds"; compatible = "gpio-leds";
pinctrl-names = "default"; pinctrl-names = "default";
...@@ -181,12 +84,107 @@ ...@@ -181,12 +84,107 @@
enable-active-high; enable-active-high;
gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>; gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>;
}; };
};
&ahci {
status = "okay";
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupts = <0>;
interrupt-controller;
#interrupt-cells = <1>;
};
};
&ir0 {
pinctrl-names = "default";
pinctrl-0 = <&ir0_pins_a>;
status = "okay";
};
&mdio {
phy-supply = <&reg_emac_3v3>;
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
cd-inverted;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
reg_usb1_vbus: usb1-vbus { &pio {
status = "okay"; emac_power_pin_a1000: emac_power_pin@0 {
allwinner,pins = "PH15";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
}; };
reg_usb2_vbus: usb2-vbus { led_pins_a1000: led_pins@0 {
status = "okay"; allwinner,pins = "PH10", "PH20";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
}; };
}; };
&reg_usb1_vbus {
status = "okay";
};
&reg_usb2_vbus {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usbphy {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册